1 /* 2 * (C) Copyright 2013 Siemens Schweiz AG 3 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 4 * 5 * Based on: 6 * U-Boot file:/include/configs/am335x_evm.h 7 * 8 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_THUBAN_H 14 #define __CONFIG_THUBAN_H 15 16 #include "siemens-am33x-common.h" 17 18 #define CONFIG_DISPLAY_CPUINFO 19 #define CONFIG_SYS_MPUCLK 300 20 #define DDR_PLL_FREQ 303 21 #undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC 22 23 #define BOARD_DFU_BUTTON_GPIO 27 /* Use as default */ 24 #define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ 25 26 #define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 27 "button_dfu0=27\0" \ 28 "led0=103,1,0\0" \ 29 "led1=64,0,1\0" 30 31 #undef CONFIG_DOS_PARTITION 32 33 #define CONFIG_BOARD_LATE_INIT 34 35 /* Physical Memory Map */ 36 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 37 38 /* I2C Configuration */ 39 #define CONFIG_SYS_I2C_SPEED 100000 40 41 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 42 #define EEPROM_ADDR_DDR3 0x90 43 #define EEPROM_ADDR_CHIP 0x120 44 45 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300 46 47 #undef CONFIG_MII 48 #undef CONFIG_PHY_GIGE 49 #define CONFIG_PHY_SMSC 50 51 #define CONFIG_FACTORYSET 52 53 /* Watchdog */ 54 #define CONFIG_OMAP_WATCHDOG 55 56 /* Define own nand partitions */ 57 #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 58 #define CONFIG_ENV_SIZE_REDUND 0x2000 59 #define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE) 60 61 #define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V2 62 63 #ifndef CONFIG_SPL_BUILD 64 65 /* Default env settings */ 66 #define CONFIG_EXTRA_ENV_SETTINGS \ 67 "hostname=thuban\0" \ 68 "ubi_off=2048\0"\ 69 "nand_img_size=0x400000\0" \ 70 "optargs=\0" \ 71 "preboot=draco_led 0\0" \ 72 CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 73 CONFIG_ENV_SETTINGS_V2 \ 74 CONFIG_ENV_SETTINGS_NAND_V2 75 76 #ifndef CONFIG_RESTORE_FLASH 77 /* set to negative value for no autoboot */ 78 79 #define CONFIG_BOOTCOMMAND \ 80 "if dfubutton; then " \ 81 "run dfu_start; " \ 82 "reset; " \ 83 "fi;" \ 84 "run nand_boot;" \ 85 "run nand_boot_backup;" \ 86 "reset;" 87 88 #else 89 90 #define CONFIG_BOOTCOMMAND \ 91 "setenv autoload no; " \ 92 "dhcp; " \ 93 "if tftp 80000000 debrick.scr; then " \ 94 "source 80000000; " \ 95 "fi" 96 #endif 97 #endif /* CONFIG_SPL_BUILD */ 98 #endif /* ! __CONFIG_THUBAN_H */ 99