1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2014 Soeren Moch <smoch@web.de> 4 * 5 * Configuration settings for the TBS2910 MatrixARM board. 6 */ 7 8 #ifndef __TBS2910_CONFIG_H 9 #define __TBS2910_CONFIG_H 10 11 #include "mx6_common.h" 12 13 /* General configuration */ 14 15 #define CONFIG_MACH_TYPE 3980 16 17 #define CONFIG_SYS_HZ 1000 18 19 #define CONFIG_IMX_THERMAL 20 21 /* Physical Memory Map */ 22 #define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR 23 24 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 25 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 26 #define CONFIG_SYS_INIT_SP_OFFSET \ 27 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 28 #define CONFIG_SYS_INIT_SP_ADDR \ 29 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 30 31 #define CONFIG_SYS_MALLOC_LEN (128 * 1024 * 1024) 32 33 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 34 #define CONFIG_SYS_MEMTEST_END \ 35 (CONFIG_SYS_MEMTEST_START + 500 * 1024 * 1024) 36 37 #define CONFIG_SYS_BOOTMAPSZ 0x10000000 38 39 /* Serial console */ 40 #define CONFIG_MXC_UART 41 #define CONFIG_MXC_UART_BASE UART1_BASE /* select UART1/UART2 */ 42 43 /* Filesystems / image support */ 44 45 /* MMC */ 46 #define CONFIG_SYS_FSL_USDHC_NUM 3 47 #define CONFIG_SYS_FSL_ESDHC_ADDR USDHC4_BASE_ADDR 48 #define CONFIG_SUPPORT_EMMC_BOOT 49 50 /* Ethernet */ 51 #define CONFIG_FEC_MXC 52 #define CONFIG_FEC_MXC 53 #define CONFIG_MII 54 #define IMX_FEC_BASE ENET_BASE_ADDR 55 #define CONFIG_FEC_XCV_TYPE RGMII 56 #define CONFIG_ETHPRIME "FEC" 57 #define CONFIG_FEC_MXC_PHYADDR 4 58 #define CONFIG_PHY_ATHEROS 59 60 /* Framebuffer */ 61 #ifdef CONFIG_VIDEO 62 #define CONFIG_VIDEO_IPUV3 63 #define CONFIG_VIDEO_BMP_RLE8 64 #define CONFIG_IMX_HDMI 65 #define CONFIG_IMX_VIDEO_SKIP 66 #endif 67 68 /* PCI */ 69 #ifdef CONFIG_CMD_PCI 70 #define CONFIG_PCI_SCAN_SHOW 71 #define CONFIG_PCIE_IMX 72 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 73 #endif 74 75 /* SATA */ 76 #ifdef CONFIG_CMD_SATA 77 #define CONFIG_SYS_SATA_MAX_DEVICE 1 78 #define CONFIG_DWC_AHSATA_PORT_ID 0 79 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 80 #define CONFIG_LBA48 81 #endif 82 83 /* USB */ 84 #ifdef CONFIG_CMD_USB 85 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 86 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 87 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 88 #ifdef CONFIG_CMD_USB_MASS_STORAGE 89 #define CONFIG_USBD_HS 90 #endif /* CONFIG_CMD_USB_MASS_STORAGE */ 91 #ifdef CONFIG_USB_KEYBOARD 92 #define CONFIG_PREBOOT \ 93 "usb start; " \ 94 "if hdmidet; then " \ 95 "run set_con_hdmi; " \ 96 "else " \ 97 "run set_con_serial; " \ 98 "fi;" 99 #endif /* CONFIG_USB_KEYBOARD */ 100 #endif /* CONFIG_CMD_USB */ 101 102 /* RTC */ 103 #ifdef CONFIG_CMD_DATE 104 #define CONFIG_RTC_DS1307 105 #define CONFIG_SYS_RTC_BUS_NUM 2 106 #endif 107 108 /* I2C */ 109 #ifdef CONFIG_CMD_I2C 110 #define CONFIG_SYS_I2C 111 #define CONFIG_SYS_I2C_MXC 112 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 113 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 114 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 115 #define CONFIG_SYS_I2C_SPEED 100000 116 #define CONFIG_I2C_EDID 117 #endif 118 119 /* Environment organization */ 120 #define CONFIG_SYS_MMC_ENV_DEV 2 /* overwritten on SD boot */ 121 #define CONFIG_SYS_MMC_ENV_PART 1 /* overwritten on SD boot */ 122 #define CONFIG_ENV_SIZE (8 * 1024) 123 #define CONFIG_ENV_OFFSET (384 * 1024) 124 #define CONFIG_ENV_OVERWRITE 125 126 #define CONFIG_EXTRA_ENV_SETTINGS \ 127 "bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \ 128 "bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M@60 " \ 129 "video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \ 130 "bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \ 131 "bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \ 132 "${bootargs_mmc3}\0" \ 133 "bootargs_upd=setenv bootargs console=ttymxc0,115200 " \ 134 "rdinit=/sbin/init enable_wait_mode=off\0" \ 135 "bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \ 136 "mmc read 0x10800000 0x800 0x4000; bootm 0x10800000\0" \ 137 "bootcmd_up1=load mmc 1 0x10800000 uImage\0" \ 138 "bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \ 139 "run bootargs_upd; " \ 140 "bootm 0x10800000 0x10d00000\0" \ 141 "console=ttymxc0\0" \ 142 "fan=gpio set 92\0" \ 143 "set_con_serial=setenv stdout serial; " \ 144 "setenv stderr serial;\0" \ 145 "set_con_hdmi=setenv stdout serial,vga; " \ 146 "setenv stderr serial,vga;\0" \ 147 "stderr=serial,vga;\0" \ 148 "stdin=serial,usbkbd;\0" \ 149 "stdout=serial,vga;\0" 150 151 #define CONFIG_BOOTCOMMAND \ 152 "mmc rescan; " \ 153 "if run bootcmd_up1; then " \ 154 "run bootcmd_up2; " \ 155 "else " \ 156 "run bootcmd_mmc; " \ 157 "fi" 158 159 #endif /* __TBS2910_CONFIG_H * */ 160