1 /* 2 * Copyright (C) 2014 Soeren Moch <smoch@web.de> 3 * 4 * Configuration settings for the TBS2910 MatrixARM board. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __TBS2910_CONFIG_H 10 #define __TBS2910_CONFIG_H 11 12 #include "mx6_common.h" 13 14 /* General configuration */ 15 #define CONFIG_SYS_THUMB_BUILD 16 17 #define CONFIG_MACH_TYPE 3980 18 19 #define CONFIG_BOARD_EARLY_INIT_F 20 21 #define CONFIG_SYS_HZ 1000 22 23 #define CONFIG_IMX_THERMAL 24 25 /* Physical Memory Map */ 26 #define CONFIG_NR_DRAM_BANKS 1 27 #define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR 28 29 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 30 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 31 #define CONFIG_SYS_INIT_SP_OFFSET \ 32 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 33 #define CONFIG_SYS_INIT_SP_ADDR \ 34 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 35 36 #define CONFIG_SYS_MALLOC_LEN (128 * 1024 * 1024) 37 38 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 39 #define CONFIG_SYS_MEMTEST_END \ 40 (CONFIG_SYS_MEMTEST_START + 500 * 1024 * 1024) 41 42 #define CONFIG_SYS_BOOTMAPSZ 0x10000000 43 44 /* Serial console */ 45 #define CONFIG_MXC_UART 46 #define CONFIG_MXC_UART_BASE UART1_BASE /* select UART1/UART2 */ 47 #define CONFIG_BAUDRATE 115200 48 49 #define CONFIG_CONS_INDEX 1 50 51 /* *** Command definition *** */ 52 #define CONFIG_CMD_BMODE 53 #define CONFIG_CMD_PART 54 55 /* Filesystems / image support */ 56 #define CONFIG_EFI_PARTITION 57 #define CONFIG_PARTITION_UUIDS 58 59 /* MMC */ 60 #define CONFIG_SYS_FSL_USDHC_NUM 3 61 #define CONFIG_SYS_FSL_ESDHC_ADDR USDHC4_BASE_ADDR 62 #define CONFIG_SUPPORT_EMMC_BOOT 63 64 /* Ethernet */ 65 #define CONFIG_FEC_MXC 66 #define CONFIG_FEC_MXC 67 #define CONFIG_MII 68 #define IMX_FEC_BASE ENET_BASE_ADDR 69 #define CONFIG_FEC_XCV_TYPE RGMII 70 #define CONFIG_ETHPRIME "FEC" 71 #define CONFIG_FEC_MXC_PHYADDR 4 72 #define CONFIG_PHYLIB 73 #define CONFIG_PHY_ATHEROS 74 75 /* Framebuffer */ 76 #ifdef CONFIG_VIDEO 77 #define CONFIG_VIDEO_IPUV3 78 #define CONFIG_IPUV3_CLK 260000000 79 #define CONFIG_VIDEO_BMP_RLE8 80 #define CONFIG_IMX_HDMI 81 #define CONFIG_IMX_VIDEO_SKIP 82 #define CONFIG_CMD_HDMIDETECT 83 #endif 84 85 /* PCI */ 86 #define CONFIG_CMD_PCI 87 #ifdef CONFIG_CMD_PCI 88 #define CONFIG_PCI 89 #define CONFIG_PCI_PNP 90 #define CONFIG_PCI_SCAN_SHOW 91 #define CONFIG_PCIE_IMX 92 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 93 #endif 94 95 /* SATA */ 96 #define CONFIG_CMD_SATA 97 #ifdef CONFIG_CMD_SATA 98 #define CONFIG_DWC_AHSATA 99 #define CONFIG_SYS_SATA_MAX_DEVICE 1 100 #define CONFIG_DWC_AHSATA_PORT_ID 0 101 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 102 #define CONFIG_LBA48 103 #define CONFIG_LIBATA 104 #endif 105 106 /* USB */ 107 #ifdef CONFIG_CMD_USB 108 #define CONFIG_USB_EHCI 109 #define CONFIG_USB_EHCI_MX6 110 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 111 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 112 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 113 #ifdef CONFIG_CMD_USB_MASS_STORAGE 114 #define CONFIG_USBD_HS 115 #define CONFIG_USB_FUNCTION_MASS_STORAGE 116 #endif /* CONFIG_CMD_USB_MASS_STORAGE */ 117 #ifdef CONFIG_USB_KEYBOARD 118 #define CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE 119 #define CONFIG_PREBOOT \ 120 "usb start; " \ 121 "if hdmidet; then " \ 122 "run set_con_hdmi; " \ 123 "else " \ 124 "run set_con_serial; " \ 125 "fi;" 126 #endif /* CONFIG_USB_KEYBOARD */ 127 #endif /* CONFIG_CMD_USB */ 128 129 /* RTC */ 130 #define CONFIG_CMD_DATE 131 #ifdef CONFIG_CMD_DATE 132 #define CONFIG_RTC_DS1307 133 #define CONFIG_SYS_RTC_BUS_NUM 2 134 #endif 135 136 /* I2C */ 137 #ifdef CONFIG_CMD_I2C 138 #define CONFIG_SYS_I2C 139 #define CONFIG_SYS_I2C_MXC 140 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 141 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 142 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 143 #define CONFIG_SYS_I2C_SPEED 100000 144 #define CONFIG_I2C_EDID 145 #endif 146 147 /* Environment organization */ 148 #define CONFIG_ENV_IS_IN_MMC 149 #define CONFIG_SYS_MMC_ENV_DEV 2 /* overwritten on SD boot */ 150 #define CONFIG_SYS_MMC_ENV_PART 1 /* overwritten on SD boot */ 151 #define CONFIG_ENV_SIZE (8 * 1024) 152 #define CONFIG_ENV_OFFSET (384 * 1024) 153 #define CONFIG_ENV_OVERWRITE 154 155 #define CONFIG_EXTRA_ENV_SETTINGS \ 156 "bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \ 157 "bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M@60 " \ 158 "video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \ 159 "bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \ 160 "bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \ 161 "${bootargs_mmc3}\0" \ 162 "bootargs_upd=setenv bootargs console=ttymxc0,115200 " \ 163 "rdinit=/sbin/init enable_wait_mode=off\0" \ 164 "bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \ 165 "mmc read 0x10800000 0x800 0x4000; bootm 0x10800000\0" \ 166 "bootcmd_up1=load mmc 1 0x10800000 uImage\0" \ 167 "bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \ 168 "run bootargs_upd; " \ 169 "bootm 0x10800000 0x10d00000\0" \ 170 "console=ttymxc0\0" \ 171 "fan=gpio set 92\0" \ 172 "set_con_serial=setenv stdout serial; " \ 173 "setenv stderr serial;\0" \ 174 "set_con_hdmi=setenv stdout serial,vga; " \ 175 "setenv stderr serial,vga;\0" \ 176 "stderr=serial,vga;\0" \ 177 "stdin=serial,usbkbd;\0" \ 178 "stdout=serial,vga;\0" 179 180 #define CONFIG_BOOTCOMMAND \ 181 "mmc rescan; " \ 182 "if run bootcmd_up1; then " \ 183 "run bootcmd_up2; " \ 184 "else " \ 185 "run bootcmd_mmc; " \ 186 "fi" 187 188 #endif /* __TBS2910_CONFIG_H * */ 189