1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2014 Soeren Moch <smoch@web.de> 4 * 5 * Configuration settings for the TBS2910 MatrixARM board. 6 */ 7 8 #ifndef __TBS2910_CONFIG_H 9 #define __TBS2910_CONFIG_H 10 11 #include "mx6_common.h" 12 13 /* General configuration */ 14 15 #define CONFIG_MACH_TYPE 3980 16 17 #define CONFIG_SYS_HZ 1000 18 19 #define CONFIG_IMX_THERMAL 20 21 /* Physical Memory Map */ 22 #define CONFIG_NR_DRAM_BANKS 1 23 #define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR 24 25 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 26 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 27 #define CONFIG_SYS_INIT_SP_OFFSET \ 28 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 29 #define CONFIG_SYS_INIT_SP_ADDR \ 30 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 31 32 #define CONFIG_SYS_MALLOC_LEN (128 * 1024 * 1024) 33 34 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 35 #define CONFIG_SYS_MEMTEST_END \ 36 (CONFIG_SYS_MEMTEST_START + 500 * 1024 * 1024) 37 38 #define CONFIG_SYS_BOOTMAPSZ 0x10000000 39 40 /* Serial console */ 41 #define CONFIG_MXC_UART 42 #define CONFIG_MXC_UART_BASE UART1_BASE /* select UART1/UART2 */ 43 44 /* Filesystems / image support */ 45 46 /* MMC */ 47 #define CONFIG_SYS_FSL_USDHC_NUM 3 48 #define CONFIG_SYS_FSL_ESDHC_ADDR USDHC4_BASE_ADDR 49 #define CONFIG_SUPPORT_EMMC_BOOT 50 51 /* Ethernet */ 52 #define CONFIG_FEC_MXC 53 #define CONFIG_FEC_MXC 54 #define CONFIG_MII 55 #define IMX_FEC_BASE ENET_BASE_ADDR 56 #define CONFIG_FEC_XCV_TYPE RGMII 57 #define CONFIG_ETHPRIME "FEC" 58 #define CONFIG_FEC_MXC_PHYADDR 4 59 #define CONFIG_PHY_ATHEROS 60 61 /* Framebuffer */ 62 #ifdef CONFIG_VIDEO 63 #define CONFIG_VIDEO_IPUV3 64 #define CONFIG_VIDEO_BMP_RLE8 65 #define CONFIG_IMX_HDMI 66 #define CONFIG_IMX_VIDEO_SKIP 67 #endif 68 69 /* PCI */ 70 #ifdef CONFIG_CMD_PCI 71 #define CONFIG_PCI_SCAN_SHOW 72 #define CONFIG_PCIE_IMX 73 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 74 #endif 75 76 /* SATA */ 77 #ifdef CONFIG_CMD_SATA 78 #define CONFIG_SYS_SATA_MAX_DEVICE 1 79 #define CONFIG_DWC_AHSATA_PORT_ID 0 80 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 81 #define CONFIG_LBA48 82 #endif 83 84 /* USB */ 85 #ifdef CONFIG_CMD_USB 86 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 87 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 88 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 89 #ifdef CONFIG_CMD_USB_MASS_STORAGE 90 #define CONFIG_USBD_HS 91 #endif /* CONFIG_CMD_USB_MASS_STORAGE */ 92 #ifdef CONFIG_USB_KEYBOARD 93 #define CONFIG_PREBOOT \ 94 "usb start; " \ 95 "if hdmidet; then " \ 96 "run set_con_hdmi; " \ 97 "else " \ 98 "run set_con_serial; " \ 99 "fi;" 100 #endif /* CONFIG_USB_KEYBOARD */ 101 #endif /* CONFIG_CMD_USB */ 102 103 /* RTC */ 104 #ifdef CONFIG_CMD_DATE 105 #define CONFIG_RTC_DS1307 106 #define CONFIG_SYS_RTC_BUS_NUM 2 107 #endif 108 109 /* I2C */ 110 #ifdef CONFIG_CMD_I2C 111 #define CONFIG_SYS_I2C 112 #define CONFIG_SYS_I2C_MXC 113 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 114 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 115 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 116 #define CONFIG_SYS_I2C_SPEED 100000 117 #define CONFIG_I2C_EDID 118 #endif 119 120 /* Environment organization */ 121 #define CONFIG_SYS_MMC_ENV_DEV 2 /* overwritten on SD boot */ 122 #define CONFIG_SYS_MMC_ENV_PART 1 /* overwritten on SD boot */ 123 #define CONFIG_ENV_SIZE (8 * 1024) 124 #define CONFIG_ENV_OFFSET (384 * 1024) 125 #define CONFIG_ENV_OVERWRITE 126 127 #define CONFIG_EXTRA_ENV_SETTINGS \ 128 "bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \ 129 "bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M@60 " \ 130 "video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \ 131 "bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \ 132 "bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \ 133 "${bootargs_mmc3}\0" \ 134 "bootargs_upd=setenv bootargs console=ttymxc0,115200 " \ 135 "rdinit=/sbin/init enable_wait_mode=off\0" \ 136 "bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \ 137 "mmc read 0x10800000 0x800 0x4000; bootm 0x10800000\0" \ 138 "bootcmd_up1=load mmc 1 0x10800000 uImage\0" \ 139 "bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \ 140 "run bootargs_upd; " \ 141 "bootm 0x10800000 0x10d00000\0" \ 142 "console=ttymxc0\0" \ 143 "fan=gpio set 92\0" \ 144 "set_con_serial=setenv stdout serial; " \ 145 "setenv stderr serial;\0" \ 146 "set_con_hdmi=setenv stdout serial,vga; " \ 147 "setenv stderr serial,vga;\0" \ 148 "stderr=serial,vga;\0" \ 149 "stdin=serial,usbkbd;\0" \ 150 "stdout=serial,vga;\0" 151 152 #define CONFIG_BOOTCOMMAND \ 153 "mmc rescan; " \ 154 "if run bootcmd_up1; then " \ 155 "run bootcmd_up2; " \ 156 "else " \ 157 "run bootcmd_mmc; " \ 158 "fi" 159 160 #endif /* __TBS2910_CONFIG_H * */ 161