1 /* 2 * Common board functions for Siemens TAURUS (AT91SAM9G20) based boards 3 * (C) Copyright 2013 Siemens AG 4 * 5 * Based on: 6 * U-Boot file: include/configs/at91sam9260ek.h 7 * 8 * (C) Copyright 2007-2008 9 * Stelian Pop <stelian@popies.net> 10 * Lead Tech Design <www.leadtechdesign.com> 11 * 12 * SPDX-License-Identifier: GPL-2.0+ 13 */ 14 15 #ifndef __CONFIG_H 16 #define __CONFIG_H 17 18 /* 19 * SoC must be defined first, before hardware.h is included. 20 * In this case SoC is defined in boards.cfg. 21 */ 22 #include <asm/hardware.h> 23 #include <linux/sizes.h> 24 25 #if defined(CONFIG_SPL_BUILD) 26 #define CONFIG_SYS_ICACHE_OFF 27 #define CONFIG_SYS_DCACHE_OFF 28 #endif 29 /* 30 * Warning: changing CONFIG_SYS_TEXT_BASE requires 31 * adapting the initial boot program. 32 * Since the linker has to swallow that define, we must use a pure 33 * hex number here! 34 */ 35 36 #define CONFIG_SYS_TEXT_BASE 0x21000000 37 38 /* ARM asynchronous clock */ 39 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ 40 #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */ 41 42 /* Misc CPU related */ 43 #define CONFIG_ARCH_CPU_INIT 44 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 45 #define CONFIG_SETUP_MEMORY_TAGS 46 #define CONFIG_INITRD_TAG 47 #define CONFIG_SKIP_LOWLEVEL_INIT_ONLY 48 49 /* general purpose I/O */ 50 #define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ 51 #define CONFIG_AT91_GPIO 52 #define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ 53 54 /* serial console */ 55 #define CONFIG_ATMEL_USART 56 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 57 #define CONFIG_USART_ID ATMEL_ID_SYS 58 59 60 /* 61 * Command line configuration. 62 */ 63 #define CONFIG_CMD_NAND 64 65 /* 66 * SDRAM: 1 bank, min 32, max 128 MB 67 * Initialized before u-boot gets started. 68 */ 69 #define CONFIG_NR_DRAM_BANKS 1 70 #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 71 #define CONFIG_SYS_SDRAM_SIZE (128 * SZ_1M) 72 73 /* 74 * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, 75 * leaving the correct space for initial global data structure above 76 * that address while providing maximum stack area below. 77 */ 78 #define CONFIG_SYS_INIT_SP_ADDR \ 79 (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) 80 81 /* NAND flash */ 82 #ifdef CONFIG_CMD_NAND 83 #define CONFIG_NAND_ATMEL 84 #define CONFIG_SYS_MAX_NAND_DEVICE 1 85 #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 86 #define CONFIG_SYS_NAND_DBW_8 87 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 88 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 89 #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 90 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 91 #endif 92 93 /* Ethernet */ 94 #define CONFIG_MACB 95 #define CONFIG_PHYLIB 96 #define CONFIG_RMII 97 #define CONFIG_AT91_WANTS_COMMON_PHY 98 99 #define CONFIG_AT91SAM9_WATCHDOG 100 #define CONFIG_AT91_HW_WDT_TIMEOUT 15 101 #if !defined(CONFIG_SPL_BUILD) 102 /* Enable the watchdog */ 103 #define CONFIG_HW_WATCHDOG 104 #endif 105 106 /* USB */ 107 #if defined(CONFIG_BOARD_TAURUS) 108 #define CONFIG_USB_ATMEL 109 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 110 #define CONFIG_USB_OHCI_NEW 111 #define CONFIG_SYS_USB_OHCI_CPU_INIT 112 #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 113 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" 114 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 115 116 /* USB DFU support */ 117 #define CONFIG_MTD_DEVICE 118 #define CONFIG_MTD_PARTITIONS 119 120 #define CONFIG_USB_GADGET_AT91 121 122 /* DFU class support */ 123 #define CONFIG_SYS_DFU_DATA_BUF_SIZE (SZ_1M) 124 #define DFU_MANIFEST_POLL_TIMEOUT 25000 125 #endif 126 127 /* SPI EEPROM */ 128 #define CONFIG_SPI 129 #define CONFIG_ATMEL_SPI 130 #define TAURUS_SPI_MASK (1 << 4) 131 #define TAURUS_SPI_CS_PIN AT91_PIN_PA3 132 133 #if defined(CONFIG_SPL_BUILD) 134 /* SPL related */ 135 #define CONFIG_SPL_SPI_LOAD 136 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 137 138 #define CONFIG_SF_DEFAULT_BUS 0 139 #define CONFIG_SF_DEFAULT_SPEED 1000000 140 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 141 #endif 142 143 /* load address */ 144 #define CONFIG_SYS_LOAD_ADDR 0x22000000 145 146 /* bootstrap in spi flash , u-boot + env + linux in nandflash */ 147 #define CONFIG_ENV_OFFSET 0x100000 148 #define CONFIG_ENV_OFFSET_REDUND 0x180000 149 #define CONFIG_ENV_SIZE (SZ_128K) /* 1 sector = 128 kB */ 150 #define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm" 151 152 #if defined(CONFIG_BOARD_TAURUS) 153 #define CONFIG_BOOTARGS_TAURUS \ 154 "console=ttyS0,115200 earlyprintk " \ 155 "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ 156 "256k(env),256k(env_redundant),256k(spare)," \ 157 "512k(dtb),6M(kernel)ro,-(rootfs) " \ 158 "root=/dev/mtdblock7 rw rootfstype=jffs2" 159 #endif 160 161 #if defined(CONFIG_BOARD_AXM) 162 #define CONFIG_BOOTARGS_AXM \ 163 "\0" \ 164 "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:" \ 165 "${gatewayip}:${netmask}:${hostname}:${netdev}::off\0" \ 166 "addtest=setenv bootargs ${bootargs} loglevel=4 test\0" \ 167 "baudrate=115200\0" \ 168 "boot_file=setenv bootfile /${project_dir}/kernel/uImage\0" \ 169 "boot_retries=0\0" \ 170 "bootcmd=run flash_self\0" \ 171 "bootdelay=3\0" \ 172 "ethact=macb0\0" \ 173 "flash_nfs=run nand_kernel;run nfsargs;run addip;upgrade_available;"\ 174 "bootm ${kernel_ram};reset\0" \ 175 "flash_self=run nand_kernel;run setbootargs;upgrade_available;" \ 176 "bootm ${kernel_ram};reset\0" \ 177 "flash_self_test=run nand_kernel;run setbootargs addtest; " \ 178 "upgrade_available;bootm ${kernel_ram};reset\0" \ 179 "hostname=systemone\0" \ 180 "kernel_Off=0x00200000\0" \ 181 "kernel_Off_fallback=0x03800000\0" \ 182 "kernel_ram=0x21500000\0" \ 183 "kernel_size=0x00400000\0" \ 184 "kernel_size_fallback=0x00400000\0" \ 185 "loads_echo=1\0" \ 186 "nand_kernel=nand read.e ${kernel_ram} ${kernel_Off} " \ 187 "${kernel_size}\0" \ 188 "net_nfs=run boot_file;tftp ${kernel_ram} ${bootfile};" \ 189 "run nfsargs;run addip;upgrade_available;bootm " \ 190 "${kernel_ram};reset\0" \ 191 "netdev=eth0\0" \ 192 "nfsargs=run root_path;setenv bootargs ${bootargs} " \ 193 "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ 194 "at91sam9_wdt.wdt_timeout=16\0" \ 195 "partitionset_active=A\0" \ 196 "preboot=echo;echo Type 'run flash_self' to use kernel and root "\ 197 "filesystem on memory;echo Type 'run flash_nfs' to use kernel " \ 198 "from memory and root filesystem over NFS;echo Type 'run net_nfs' "\ 199 "to get Kernel over TFTP and mount root filesystem over NFS;echo\0"\ 200 "project_dir=systemone\0" \ 201 "root_path=setenv rootpath /home/projects/${project_dir}/rootfs\0"\ 202 "rootfs=/dev/mtdblock5\0" \ 203 "rootfs_fallback=/dev/mtdblock7\0" \ 204 "setbootargs=setenv bootargs ${bootargs} console=ttyMTD,mtdoops "\ 205 "root=${rootfs} rootfstype=jffs2 panic=7 " \ 206 "at91sam9_wdt.wdt_timeout=16\0" \ 207 "stderr=serial\0" \ 208 "stdin=serial\0" \ 209 "stdout=serial\0" \ 210 "upgrade_available=0\0" 211 #endif 212 213 #if defined(CONFIG_BOARD_TAURUS) 214 #define CONFIG_BOOTARGS CONFIG_BOOTARGS_TAURUS 215 #endif 216 217 #if defined(CONFIG_BOARD_AXM) 218 #define CONFIG_BOOTARGS CONFIG_BOOTARGS_AXM 219 #endif 220 221 #define CONFIG_SYS_CBSIZE 256 222 #define CONFIG_SYS_MAXARGS 16 223 #define CONFIG_SYS_PBSIZE \ 224 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 225 #define CONFIG_SYS_LONGHELP 226 #define CONFIG_CMDLINE_EDITING 227 #define CONFIG_AUTO_COMPLETE 228 229 /* 230 * Size of malloc() pool 231 */ 232 #define CONFIG_SYS_MALLOC_LEN \ 233 ROUND(3 * CONFIG_ENV_SIZE + SZ_4M, 0x1000) 234 235 /* Defines for SPL */ 236 #define CONFIG_SPL_FRAMEWORK 237 #define CONFIG_SPL_TEXT_BASE 0x0 238 #define CONFIG_SPL_MAX_SIZE (31 * SZ_512) 239 #define CONFIG_SPL_STACK (ATMEL_BASE_SRAM1 + SZ_16K) 240 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ 241 CONFIG_SYS_MALLOC_LEN) 242 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 243 244 #define CONFIG_SPL_BSS_START_ADDR CONFIG_SPL_MAX_SIZE 245 #define CONFIG_SPL_BSS_MAX_SIZE (3 * SZ_512) 246 247 #define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14) 248 #define CONFIG_SYS_USE_NANDFLASH 1 249 #define CONFIG_SPL_NAND_DRIVERS 250 #define CONFIG_SPL_NAND_BASE 251 #define CONFIG_SPL_NAND_ECC 252 #define CONFIG_SPL_NAND_RAW_ONLY 253 #define CONFIG_SPL_NAND_SOFTECC 254 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000 255 #define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K 256 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 257 #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE 258 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 259 260 #define CONFIG_SYS_NAND_SIZE (256 * SZ_1M) 261 #define CONFIG_SYS_NAND_PAGE_SIZE SZ_2K 262 #define CONFIG_SYS_NAND_BLOCK_SIZE (SZ_128K) 263 #define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ 264 CONFIG_SYS_NAND_PAGE_SIZE) 265 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS 266 #define CONFIG_SYS_NAND_ECCSIZE 256 267 #define CONFIG_SYS_NAND_ECCBYTES 3 268 #define CONFIG_SYS_NAND_OOBSIZE 64 269 #define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \ 270 48, 49, 50, 51, 52, 53, 54, 55, \ 271 56, 57, 58, 59, 60, 61, 62, 63, } 272 273 #define CONFIG_SPL_ATMEL_SIZE 274 #define CONFIG_SYS_MASTER_CLOCK 132096000 275 #define AT91_PLL_LOCK_TIMEOUT 1000000 276 #define CONFIG_SYS_AT91_PLLA 0x202A3F01 277 #define CONFIG_SYS_MCKR 0x1300 278 #define CONFIG_SYS_MCKR_CSS (0x02 | CONFIG_SYS_MCKR) 279 #define CONFIG_SYS_AT91_PLLB 0x10193F05 280 281 #endif 282