1 /* 2 * Common board functions for Siemens TAURUS (AT91SAM9G20) based boards 3 * (C) Copyright 2013 Siemens AG 4 * 5 * Based on: 6 * U-Boot file: include/configs/at91sam9260ek.h 7 * 8 * (C) Copyright 2007-2008 9 * Stelian Pop <stelian@popies.net> 10 * Lead Tech Design <www.leadtechdesign.com> 11 * 12 * SPDX-License-Identifier: GPL-2.0+ 13 */ 14 15 #ifndef __CONFIG_H 16 #define __CONFIG_H 17 18 /* 19 * SoC must be defined first, before hardware.h is included. 20 * In this case SoC is defined in boards.cfg. 21 */ 22 #include <asm/hardware.h> 23 #include <linux/sizes.h> 24 25 #if defined(CONFIG_SPL_BUILD) 26 #define CONFIG_SYS_THUMB_BUILD 27 #define CONFIG_SYS_ICACHE_OFF 28 #define CONFIG_SYS_DCACHE_OFF 29 #endif 30 /* 31 * Warning: changing CONFIG_SYS_TEXT_BASE requires 32 * adapting the initial boot program. 33 * Since the linker has to swallow that define, we must use a pure 34 * hex number here! 35 */ 36 37 #define CONFIG_SYS_TEXT_BASE 0x21000000 38 39 /* ARM asynchronous clock */ 40 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ 41 #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */ 42 43 /* Misc CPU related */ 44 #define CONFIG_ARCH_CPU_INIT 45 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 46 #define CONFIG_SETUP_MEMORY_TAGS 47 #define CONFIG_INITRD_TAG 48 #define CONFIG_SKIP_LOWLEVEL_INIT_ONLY 49 #define CONFIG_BOARD_EARLY_INIT_F 50 51 /* general purpose I/O */ 52 #define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ 53 #define CONFIG_AT91_GPIO 54 #define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ 55 56 /* serial console */ 57 #define CONFIG_ATMEL_USART 58 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 59 #define CONFIG_USART_ID ATMEL_ID_SYS 60 #define CONFIG_BAUDRATE 115200 61 62 63 /* 64 * Command line configuration. 65 */ 66 #define CONFIG_CMD_NAND 67 68 /* 69 * SDRAM: 1 bank, min 32, max 128 MB 70 * Initialized before u-boot gets started. 71 */ 72 #define CONFIG_NR_DRAM_BANKS 1 73 #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 74 #define CONFIG_SYS_SDRAM_SIZE (128 * SZ_1M) 75 76 /* 77 * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, 78 * leaving the correct space for initial global data structure above 79 * that address while providing maximum stack area below. 80 */ 81 #define CONFIG_SYS_INIT_SP_ADDR \ 82 (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) 83 84 /* NAND flash */ 85 #ifdef CONFIG_CMD_NAND 86 #define CONFIG_NAND_ATMEL 87 #define CONFIG_SYS_MAX_NAND_DEVICE 1 88 #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 89 #define CONFIG_SYS_NAND_DBW_8 90 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 91 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 92 #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 93 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 94 #endif 95 96 /* NOR flash - no real flash on this board */ 97 #define CONFIG_SYS_NO_FLASH 1 98 99 /* Ethernet */ 100 #define CONFIG_MACB 101 #define CONFIG_PHYLIB 102 #define CONFIG_RMII 103 #define CONFIG_AT91_WANTS_COMMON_PHY 104 105 #define CONFIG_AT91SAM9_WATCHDOG 106 #define CONFIG_AT91_HW_WDT_TIMEOUT 15 107 #if !defined(CONFIG_SPL_BUILD) 108 /* Enable the watchdog */ 109 #define CONFIG_HW_WATCHDOG 110 #endif 111 112 /* USB */ 113 #if defined(CONFIG_BOARD_TAURUS) 114 #define CONFIG_USB_ATMEL 115 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 116 #define CONFIG_USB_OHCI_NEW 117 #define CONFIG_SYS_USB_OHCI_CPU_INIT 118 #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 119 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" 120 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 121 122 /* USB DFU support */ 123 #define CONFIG_CMD_MTDPARTS 124 #define CONFIG_MTD_DEVICE 125 #define CONFIG_MTD_PARTITIONS 126 127 #define CONFIG_USB_GADGET_AT91 128 129 /* DFU class support */ 130 #define CONFIG_SYS_DFU_DATA_BUF_SIZE (SZ_1M) 131 #define DFU_MANIFEST_POLL_TIMEOUT 25000 132 #endif 133 134 /* SPI EEPROM */ 135 #define CONFIG_SPI 136 #define CONFIG_ATMEL_SPI 137 #define TAURUS_SPI_MASK (1 << 4) 138 #define TAURUS_SPI_CS_PIN AT91_PIN_PA3 139 140 #if defined(CONFIG_SPL_BUILD) 141 /* SPL related */ 142 #define CONFIG_SPL_SPI_LOAD 143 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 144 145 #define CONFIG_SF_DEFAULT_BUS 0 146 #define CONFIG_SF_DEFAULT_SPEED 1000000 147 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 148 #endif 149 150 /* load address */ 151 #define CONFIG_SYS_LOAD_ADDR 0x22000000 152 153 /* bootstrap in spi flash , u-boot + env + linux in nandflash */ 154 #define CONFIG_ENV_IS_IN_NAND 155 #define CONFIG_ENV_OFFSET 0x100000 156 #define CONFIG_ENV_OFFSET_REDUND 0x180000 157 #define CONFIG_ENV_SIZE (SZ_128K) /* 1 sector = 128 kB */ 158 #define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm" 159 160 #if defined(CONFIG_BOARD_TAURUS) 161 #define CONFIG_BOOTARGS_TAURUS \ 162 "console=ttyS0,115200 earlyprintk " \ 163 "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ 164 "256k(env),256k(env_redundant),256k(spare)," \ 165 "512k(dtb),6M(kernel)ro,-(rootfs) " \ 166 "root=/dev/mtdblock7 rw rootfstype=jffs2" 167 #endif 168 169 #if defined(CONFIG_BOARD_AXM) 170 #define CONFIG_BOOTARGS_AXM \ 171 "\0" \ 172 "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:" \ 173 "${gatewayip}:${netmask}:${hostname}:${netdev}::off\0" \ 174 "addtest=setenv bootargs ${bootargs} loglevel=4 test\0" \ 175 "baudrate=115200\0" \ 176 "boot_file=setenv bootfile /${project_dir}/kernel/uImage\0" \ 177 "boot_retries=0\0" \ 178 "bootcmd=run flash_self\0" \ 179 "bootdelay=3\0" \ 180 "ethact=macb0\0" \ 181 "flash_nfs=run nand_kernel;run nfsargs;run addip;upgrade_available;"\ 182 "bootm ${kernel_ram};reset\0" \ 183 "flash_self=run nand_kernel;run setbootargs;upgrade_available;" \ 184 "bootm ${kernel_ram};reset\0" \ 185 "flash_self_test=run nand_kernel;run setbootargs addtest; " \ 186 "upgrade_available;bootm ${kernel_ram};reset\0" \ 187 "hostname=systemone\0" \ 188 "kernel_Off=0x00200000\0" \ 189 "kernel_Off_fallback=0x03800000\0" \ 190 "kernel_ram=0x21500000\0" \ 191 "kernel_size=0x00400000\0" \ 192 "kernel_size_fallback=0x00400000\0" \ 193 "loads_echo=1\0" \ 194 "nand_kernel=nand read.e ${kernel_ram} ${kernel_Off} " \ 195 "${kernel_size}\0" \ 196 "net_nfs=run boot_file;tftp ${kernel_ram} ${bootfile};" \ 197 "run nfsargs;run addip;upgrade_available;bootm " \ 198 "${kernel_ram};reset\0" \ 199 "netdev=eth0\0" \ 200 "nfsargs=run root_path;setenv bootargs ${bootargs} " \ 201 "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ 202 "at91sam9_wdt.wdt_timeout=16\0" \ 203 "partitionset_active=A\0" \ 204 "preboot=echo;echo Type 'run flash_self' to use kernel and root "\ 205 "filesystem on memory;echo Type 'run flash_nfs' to use kernel " \ 206 "from memory and root filesystem over NFS;echo Type 'run net_nfs' "\ 207 "to get Kernel over TFTP and mount root filesystem over NFS;echo\0"\ 208 "project_dir=systemone\0" \ 209 "root_path=setenv rootpath /home/projects/${project_dir}/rootfs\0"\ 210 "rootfs=/dev/mtdblock5\0" \ 211 "rootfs_fallback=/dev/mtdblock7\0" \ 212 "setbootargs=setenv bootargs ${bootargs} console=ttyMTD,mtdoops "\ 213 "root=${rootfs} rootfstype=jffs2 panic=7 " \ 214 "at91sam9_wdt.wdt_timeout=16\0" \ 215 "stderr=serial\0" \ 216 "stdin=serial\0" \ 217 "stdout=serial\0" \ 218 "upgrade_available=0\0" 219 #endif 220 221 #if defined(CONFIG_BOARD_TAURUS) 222 #define CONFIG_BOOTARGS CONFIG_BOOTARGS_TAURUS 223 #endif 224 225 #if defined(CONFIG_BOARD_AXM) 226 #define CONFIG_BOOTARGS CONFIG_BOOTARGS_AXM 227 #endif 228 229 #define CONFIG_SYS_CBSIZE 256 230 #define CONFIG_SYS_MAXARGS 16 231 #define CONFIG_SYS_PBSIZE \ 232 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 233 #define CONFIG_SYS_LONGHELP 234 #define CONFIG_CMDLINE_EDITING 235 #define CONFIG_AUTO_COMPLETE 236 237 /* 238 * Size of malloc() pool 239 */ 240 #define CONFIG_SYS_MALLOC_LEN \ 241 ROUND(3 * CONFIG_ENV_SIZE + SZ_4M, 0x1000) 242 243 /* Defines for SPL */ 244 #define CONFIG_SPL_FRAMEWORK 245 #define CONFIG_SPL_TEXT_BASE 0x0 246 #define CONFIG_SPL_MAX_SIZE (31 * SZ_512) 247 #define CONFIG_SPL_STACK (ATMEL_BASE_SRAM1 + SZ_16K) 248 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ 249 CONFIG_SYS_MALLOC_LEN) 250 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 251 252 #define CONFIG_SPL_BSS_START_ADDR CONFIG_SPL_MAX_SIZE 253 #define CONFIG_SPL_BSS_MAX_SIZE (3 * SZ_512) 254 255 #define CONFIG_SPL_BOARD_INIT 256 #define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14) 257 #define CONFIG_SYS_USE_NANDFLASH 1 258 #define CONFIG_SPL_NAND_DRIVERS 259 #define CONFIG_SPL_NAND_BASE 260 #define CONFIG_SPL_NAND_ECC 261 #define CONFIG_SPL_NAND_RAW_ONLY 262 #define CONFIG_SPL_NAND_SOFTECC 263 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000 264 #define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K 265 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 266 #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE 267 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 268 269 #define CONFIG_SYS_NAND_SIZE (256 * SZ_1M) 270 #define CONFIG_SYS_NAND_PAGE_SIZE SZ_2K 271 #define CONFIG_SYS_NAND_BLOCK_SIZE (SZ_128K) 272 #define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ 273 CONFIG_SYS_NAND_PAGE_SIZE) 274 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS 275 #define CONFIG_SYS_NAND_ECCSIZE 256 276 #define CONFIG_SYS_NAND_ECCBYTES 3 277 #define CONFIG_SYS_NAND_OOBSIZE 64 278 #define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \ 279 48, 49, 50, 51, 52, 53, 54, 55, \ 280 56, 57, 58, 59, 60, 61, 62, 63, } 281 282 #define CONFIG_SPL_ATMEL_SIZE 283 #define CONFIG_SYS_MASTER_CLOCK 132096000 284 #define AT91_PLL_LOCK_TIMEOUT 1000000 285 #define CONFIG_SYS_AT91_PLLA 0x202A3F01 286 #define CONFIG_SYS_MCKR 0x1300 287 #define CONFIG_SYS_MCKR_CSS (0x02 | CONFIG_SYS_MCKR) 288 #define CONFIG_SYS_AT91_PLLB 0x10193F05 289 290 #endif 291