1 /* 2 * Configuration settings for the TechNexion TAO-3530 SOM 3 * equipped on Thunder baseboard. 4 * 5 * Edward Lin <linuxfae@technexion.com> 6 * Tapani Utriainen <linuxfae@technexion.com> 7 * 8 * Copyright (C) 2013 Stefan Roese <sr@denx.de> 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 /* 17 * High Level Configuration Options 18 */ 19 20 #define CONFIG_SDRC /* Has an SDRC controller */ 21 22 #include <asm/arch/cpu.h> /* get chip and board defs */ 23 #include <asm/arch/omap.h> 24 25 /* Clock Defines */ 26 #define V_OSCK 26000000 /* Clock output from T2 */ 27 #define V_SCLK (V_OSCK >> 1) 28 29 #define CONFIG_MISC_INIT_R 30 31 #define CONFIG_CMDLINE_TAG 32 #define CONFIG_SETUP_MEMORY_TAGS 33 #define CONFIG_INITRD_TAG 34 #define CONFIG_REVISION_TAG 35 36 /* 37 * Size of malloc() pool 38 */ 39 #define CONFIG_SYS_MALLOC_LEN (4 << 20) 40 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ 41 42 /* 43 * Hardware drivers 44 */ 45 46 /* 47 * NS16550 Configuration 48 */ 49 #define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 50 51 #define CONFIG_SYS_NS16550_SERIAL 52 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 53 #define CONFIG_SYS_NS16550_CLK V_NS16550_CLK 54 55 /* 56 * select serial console configuration 57 */ 58 #define CONFIG_CONS_INDEX 3 59 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 60 61 /* allow to overwrite serial and ethaddr */ 62 #define CONFIG_ENV_OVERWRITE 63 64 /* commands to include */ 65 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 66 #define MTDIDS_DEFAULT "nand0=nand" 67 #define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\ 68 "1920k(u-boot),128k(u-boot-env),"\ 69 "4m(kernel),-(fs)" 70 71 #define CONFIG_SYS_I2C 72 #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 73 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 74 #define CONFIG_I2C_MULTI_BUS 75 76 /* 77 * TWL4030 78 */ 79 #define CONFIG_TWL4030_LED 80 81 /* 82 * Board NAND Info. 83 */ 84 #define CONFIG_NAND_OMAP_GPMC 85 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ 86 /* to access nand */ 87 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 88 /* to access nand at */ 89 /* CS0 */ 90 91 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ 92 /* devices */ 93 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT 94 /* Environment information */ 95 96 #define CONFIG_EXTRA_ENV_SETTINGS \ 97 "loadaddr=0x82000000\0" \ 98 "console=ttyO2,115200n8\0" \ 99 "mpurate=600\0" \ 100 "dvi_mode=omapfb.mode=dvi:1280x720-24@60\0" \ 101 "tv_mode=omapfb.mode=tv:ntsc\0" \ 102 "video_mode=omapdss.def_disp=lcd vram=6M omapfb.vram=0:2M,1:2M,2:2M\0" \ 103 "lcd_mode=omapfb.mode=lcd:800x480@60 \0" \ 104 "extra_options= \0" \ 105 "mmcdev=0\0" \ 106 "mmcroot=/dev/mmcblk0p2 rw\0" \ 107 "mmcrootfstype=ext3 rootwait\0" \ 108 "nandroot=ubi0:rootfs ubi.mtd=4\0" \ 109 "nandrootfstype=ubifs\0" \ 110 "mmcargs=setenv bootargs console=${console} " \ 111 "mpurate=${mpurate} " \ 112 "${video_mode} " \ 113 "root=${mmcroot} " \ 114 "rootfstype=${mmcrootfstype} " \ 115 "${extra_options}\0" \ 116 "nandargs=setenv bootargs console=${console} " \ 117 "mpurate=${mpurate} " \ 118 "${video_mode} " \ 119 "${network_setting} " \ 120 "root=${nandroot} " \ 121 "rootfstype=${nandrootfstype} "\ 122 "${extra_options}\0" \ 123 "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 124 "bootscript=echo Running bootscript from mmc ...; " \ 125 "source ${loadaddr}\0" \ 126 "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ 127 "mmcboot=echo Booting from mmc ...; " \ 128 "run mmcargs; " \ 129 "bootm ${loadaddr}\0" \ 130 "nandboot=echo Booting from nand ...; " \ 131 "run nandargs; " \ 132 "nand read ${loadaddr} 280000 400000; " \ 133 "bootm ${loadaddr}\0" \ 134 135 #define CONFIG_BOOTCOMMAND \ 136 "if mmc rescan ${mmcdev}; then " \ 137 "if run loadbootscript; then " \ 138 "run bootscript; " \ 139 "else " \ 140 "if run loaduimage; then " \ 141 "run mmcboot; " \ 142 "else run nandboot; " \ 143 "fi; " \ 144 "fi; " \ 145 "else run nandboot; fi" 146 147 /* 148 * Miscellaneous configurable options 149 */ 150 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 151 152 /* turn on command-line edit/hist/auto */ 153 #define CONFIG_CMDLINE_EDITING 154 #define CONFIG_AUTO_COMPLETE 155 156 #define CONFIG_SYS_ALT_MEMTEST 1 157 #define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */ 158 /* defaults */ 159 #define CONFIG_SYS_MEMTEST_END (0x83FFFFFF) /* 64MB */ 160 #define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */ 161 162 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ 163 /* load address */ 164 #define CONFIG_SYS_TEXT_BASE 0x80008000 165 166 /* 167 * OMAP3 has 12 GP timers, they can be driven by the system clock 168 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 169 * This rate is divided by a local divisor. 170 */ 171 #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) 172 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 173 174 /* 175 * Physical Memory Map 176 */ 177 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 178 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 179 #define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */ 180 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 181 182 /* 183 * FLASH and environment organization 184 */ 185 186 /* **** PISMO SUPPORT *** */ 187 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ 188 #define CONFIG_SYS_FLASH_BASE NAND_BASE 189 190 /* Monitor at start of flash */ 191 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 192 #define CONFIG_SYS_ONENAND_BASE ONENAND_MAP 193 194 #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ 195 196 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) 197 #define CONFIG_ENV_OFFSET 0x260000 198 #define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET 199 200 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 201 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 202 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 203 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 204 CONFIG_SYS_INIT_RAM_SIZE - \ 205 GENERATED_GBL_DATA_SIZE) 206 207 /* 208 * USB 209 * 210 * Currently only EHCI is enabled, the MUSB OTG controller 211 * is not enabled. 212 */ 213 214 /* USB EHCI */ 215 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 162 216 217 #define CONFIG_USB_ETHER 218 219 /* Defines for SPL */ 220 #define CONFIG_SPL_FRAMEWORK 221 #define CONFIG_SPL_NAND_SIMPLE 222 223 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 224 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 225 226 #define CONFIG_SPL_NAND_BASE 227 #define CONFIG_SPL_NAND_DRIVERS 228 #define CONFIG_SPL_NAND_ECC 229 230 /* NAND boot config */ 231 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 232 #define CONFIG_SYS_NAND_PAGE_COUNT 64 233 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 234 #define CONFIG_SYS_NAND_OOBSIZE 64 235 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 236 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS 237 /* 238 * Use the ECC/OOB layout from omap_gpmc.h that matches your chip: 239 * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT 240 */ 241 #define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ 242 10, 11, 12, 13 } 243 #define CONFIG_SYS_NAND_ECCSIZE 512 244 #define CONFIG_SYS_NAND_ECCBYTES 3 245 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW 246 247 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 248 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 249 250 #define CONFIG_SPL_TEXT_BASE 0x40200800 251 #define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ 252 CONFIG_SPL_TEXT_BASE) 253 254 /* 255 * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the 256 * older x-loader implementations. And move the BSS area so that it 257 * doesn't overlap with TEXT_BASE. 258 */ 259 #define CONFIG_SYS_TEXT_BASE 0x80008000 260 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 261 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ 262 263 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 264 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 265 266 #endif /* __CONFIG_H */ 267