1 /* 2 * Copyright (C) 2011 3 * Stefano Babic, DENX Software Engineering, sbabic@denx.de. 4 * 5 * Copyright (C) 2009 TechNexion Ltd. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __TAM3517_H 11 #define __TAM3517_H 12 13 /* 14 * High Level Configuration Options 15 */ 16 #define CONFIG_OMAP /* in a TI OMAP core */ 17 #define CONFIG_OMAP_GPIO 18 /* Common ARM Erratas */ 19 #define CONFIG_ARM_ERRATA_454179 20 #define CONFIG_ARM_ERRATA_430973 21 #define CONFIG_ARM_ERRATA_621766 22 23 #define CONFIG_SYS_TEXT_BASE 0x80008000 24 25 #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ 26 27 #include <asm/arch/cpu.h> /* get chip and board defs */ 28 #include <asm/arch/omap.h> 29 30 /* Clock Defines */ 31 #define V_OSCK 26000000 /* Clock output from T2 */ 32 #define V_SCLK (V_OSCK >> 1) 33 34 #define CONFIG_MISC_INIT_R 35 36 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 37 #define CONFIG_SETUP_MEMORY_TAGS 38 #define CONFIG_INITRD_TAG 39 #define CONFIG_REVISION_TAG 40 41 /* 42 * Size of malloc() pool 43 */ 44 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ 45 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \ 46 2 * 1024 * 1024) 47 /* 48 * DDR related 49 */ 50 #define CONFIG_OMAP3_MICRON_DDR /* Micron DDR */ 51 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024) 52 53 /* 54 * Hardware drivers 55 */ 56 57 /* 58 * NS16550 Configuration 59 */ 60 #define CONFIG_SYS_NS16550_SERIAL 61 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 62 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 63 64 /* 65 * select serial console configuration 66 */ 67 #define CONFIG_CONS_INDEX 1 68 #define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 69 #define CONFIG_SERIAL1 /* UART1 */ 70 71 /* allow to overwrite serial and ethaddr */ 72 #define CONFIG_ENV_OVERWRITE 73 #define CONFIG_BAUDRATE 115200 74 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 75 115200} 76 #define CONFIG_GENERIC_MMC 77 #define CONFIG_DOS_PARTITION 78 79 /* EHCI */ 80 #define CONFIG_OMAP3_GPIO_5 81 #define CONFIG_USB_EHCI 82 #define CONFIG_USB_EHCI_OMAP 83 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25 84 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 85 86 /* commands to include */ 87 #define CONFIG_CMD_NAND /* NAND support */ 88 #define CONFIG_CMD_EEPROM 89 90 #define CONFIG_SYS_NO_FLASH 91 #define CONFIG_SYS_I2C 92 #define CONFIG_SYS_OMAP24_I2C_SPEED 400000 93 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 94 #define CONFIG_SYS_I2C_OMAP34XX 95 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ 96 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ 97 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 98 99 /* 100 * Board NAND Info. 101 */ 102 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 103 /* to access */ 104 /* nand at CS0 */ 105 106 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ 107 /* NAND devices */ 108 109 #define CONFIG_AUTO_COMPLETE 110 111 /* 112 * Miscellaneous configurable options 113 */ 114 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 115 #define CONFIG_CMDLINE_EDITING 116 #define CONFIG_AUTO_COMPLETE 117 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 118 119 /* Print Buffer Size */ 120 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 121 sizeof(CONFIG_SYS_PROMPT) + 16) 122 #define CONFIG_SYS_MAXARGS 32 /* max number of command */ 123 /* args */ 124 /* Boot Argument Buffer Size */ 125 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 126 /* memtest works on */ 127 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) 128 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 129 0x01F00000) /* 31MB */ 130 131 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ 132 /* address */ 133 134 /* 135 * AM3517 has 12 GP timers, they can be driven by the system clock 136 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 137 * This rate is divided by a local divisor. 138 */ 139 #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 140 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 141 142 /* 143 * Physical Memory Map 144 */ 145 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 146 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 147 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 148 149 /* 150 * FLASH and environment organization 151 */ 152 153 /* **** PISMO SUPPORT *** */ 154 #define CONFIG_NAND 155 #define CONFIG_NAND_OMAP_GPMC 156 #define CONFIG_ENV_IS_IN_NAND 157 #define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */ 158 159 /* Redundant Environment */ 160 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ 161 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 162 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 163 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 164 2 * CONFIG_SYS_ENV_SECT_SIZE) 165 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 166 167 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 168 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 169 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 170 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 171 CONFIG_SYS_INIT_RAM_SIZE - \ 172 GENERATED_GBL_DATA_SIZE) 173 174 /* 175 * ethernet support, EMAC 176 * 177 */ 178 #define CONFIG_DRIVER_TI_EMAC 179 #define CONFIG_DRIVER_TI_EMAC_USE_RMII 180 #define CONFIG_MII 181 #define CONFIG_EMAC_MDIO_PHY_NUM 0 182 #define CONFIG_BOOTP_DNS 183 #define CONFIG_BOOTP_DNS2 184 #define CONFIG_BOOTP_SEND_HOSTNAME 185 #define CONFIG_NET_RETRY_COUNT 10 186 187 /* Defines for SPL */ 188 #define CONFIG_SPL_FRAMEWORK 189 #define CONFIG_SPL_BOARD_INIT 190 #define CONFIG_SPL_CONSOLE 191 #define CONFIG_SPL_NAND_SIMPLE 192 #define CONFIG_SPL_NAND_SOFTECC 193 #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */ 194 195 #define CONFIG_SPL_NAND_BASE 196 #define CONFIG_SPL_NAND_DRIVERS 197 #define CONFIG_SPL_NAND_ECC 198 #define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds" 199 200 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ 201 #define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ 202 CONFIG_SPL_TEXT_BASE) 203 #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK 204 205 #define CONFIG_SYS_SPL_MALLOC_START 0x8f000000 206 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 207 #define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */ 208 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 209 210 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 211 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 212 213 /* FAT */ 214 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 215 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" 216 217 /* RAW SD card / eMMC */ 218 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ 219 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ 220 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ 221 222 /* NAND boot config */ 223 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT 224 #define CONFIG_SYS_NAND_PAGE_COUNT 64 225 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 226 #define CONFIG_SYS_NAND_OOBSIZE 64 227 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 228 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 229 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 230 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\ 231 48, 49, 50, 51, 52, 53, 54, 55,\ 232 56, 57, 58, 59, 60, 61, 62, 63} 233 #define CONFIG_SYS_NAND_ECCSIZE 256 234 #define CONFIG_SYS_NAND_ECCBYTES 3 235 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW 236 #define CONFIG_NAND_OMAP_GPMC_PREFETCH 237 238 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 239 240 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 241 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000 242 243 #define CONFIG_CMD_UBIFS 244 #define CONFIG_RBTREE 245 #define CONFIG_LZO 246 #define CONFIG_MTD_PARTITIONS 247 #define CONFIG_MTD_DEVICE 248 #define CONFIG_CMD_MTDPARTS 249 250 /* Setup MTD for NAND on the SOM */ 251 #define MTDIDS_DEFAULT "nand0=omap2-nand.0" 252 #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO)," \ 253 "1m(u-boot),256k(env1)," \ 254 "256k(env2),6m(kernel),-(rootfs)" 255 256 #define CONFIG_TAM3517_SETTINGS \ 257 "netdev=eth0\0" \ 258 "nandargs=setenv bootargs root=${nandroot} " \ 259 "rootfstype=${nandrootfstype}\0" \ 260 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 261 "nfsroot=${serverip}:${rootpath}\0" \ 262 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 263 "addip_sta=setenv bootargs ${bootargs} " \ 264 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 265 ":${hostname}:${netdev}:off panic=1\0" \ 266 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ 267 "addip=if test -n ${ipdyn};then run addip_dyn;" \ 268 "else run addip_sta;fi\0" \ 269 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 270 "addtty=setenv bootargs ${bootargs}" \ 271 " console=ttyO0,${baudrate}\0" \ 272 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ 273 "loadaddr=82000000\0" \ 274 "kernel_addr_r=82000000\0" \ 275 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \ 276 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \ 277 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 278 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 279 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 280 "bootm ${kernel_addr}\0" \ 281 "nandboot=run nandargs addip addtty addmtd addmisc;" \ 282 "nand read ${kernel_addr_r} kernel\0" \ 283 "bootm ${kernel_addr_r}\0" \ 284 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 285 "run nfsargs addip addtty addmtd addmisc;" \ 286 "bootm ${kernel_addr_r}\0" \ 287 "net_self=if run net_self_load;then " \ 288 "run ramargs addip addtty addmtd addmisc;" \ 289 "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \ 290 "else echo Images not loades;fi\0" \ 291 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \ 292 "load=tftp ${loadaddr} ${u-boot}\0" \ 293 "loadmlo=tftp ${loadaddr} ${mlo}\0" \ 294 "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \ 295 "uboot_addr=0x80000\0" \ 296 "update=nandecc sw;nand erase ${uboot_addr} 100000;" \ 297 "nand write ${loadaddr} ${uboot_addr} 80000\0" \ 298 "updatemlo=nandecc hw;nand erase 0 20000;" \ 299 "nand write ${loadaddr} 0 20000\0" \ 300 "upd=if run load;then echo Updating u-boot;if run update;" \ 301 "then echo U-Boot updated;" \ 302 "else echo Error updating u-boot !;" \ 303 "echo Board without bootloader !!;" \ 304 "fi;" \ 305 "else echo U-Boot not downloaded..exiting;fi\0" \ 306 307 /* 308 * this is common code for all TAM3517 boards. 309 * MAC address is stored from manufacturer in 310 * I2C EEPROM 311 */ 312 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) 313 /* 314 * The I2C EEPROM on the TAM3517 contains 315 * mac address and production data 316 */ 317 struct tam3517_module_info { 318 char customer[48]; 319 char product[48]; 320 321 /* 322 * bit 0~47 : sequence number 323 * bit 48~55 : week of year, from 0. 324 * bit 56~63 : year 325 */ 326 unsigned long long sequence_number; 327 328 /* 329 * bit 0~7 : revision fixed 330 * bit 8~15 : revision major 331 * bit 16~31 : TNxxx 332 */ 333 unsigned int revision; 334 unsigned char eth_addr[4][8]; 335 unsigned char _rev[100]; 336 }; 337 338 #define TAM3517_READ_EEPROM(info, ret) \ 339 do { \ 340 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \ 341 if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ 342 (void *)info, sizeof(*info))) \ 343 ret = 1; \ 344 else \ 345 ret = 0; \ 346 } while (0) 347 348 #define TAM3517_READ_MAC_FROM_EEPROM(info) \ 349 do { \ 350 char buf[80], ethname[20]; \ 351 int i; \ 352 memset(buf, 0, sizeof(buf)); \ 353 for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \ 354 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \ 355 (info)->eth_addr[i][5], \ 356 (info)->eth_addr[i][4], \ 357 (info)->eth_addr[i][3], \ 358 (info)->eth_addr[i][2], \ 359 (info)->eth_addr[i][1], \ 360 (info)->eth_addr[i][0]); \ 361 \ 362 if (i) \ 363 sprintf(ethname, "eth%daddr", i); \ 364 else \ 365 strcpy(ethname, "ethaddr"); \ 366 printf("Setting %s from EEPROM with %s\n", ethname, buf);\ 367 setenv(ethname, buf); \ 368 } \ 369 } while (0) 370 371 /* The following macros are taken from Technexion's documentation */ 372 #define TAM3517_sequence_number(info) \ 373 ((info)->sequence_number % 0x1000000000000LL) 374 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100) 375 #define TAM3517_year(info) ((info)->sequence_number >> 56) 376 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100) 377 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100) 378 #define TAM3517_revision_tn(info) ((info)->revision >> 16) 379 380 #define TAM3517_PRINT_SOM_INFO(info) \ 381 do { \ 382 printf("Vendor:%s\n", (info)->customer); \ 383 printf("SOM: %s\n", (info)->product); \ 384 printf("SeqNr: %02llu%02llu%012llu\n", \ 385 TAM3517_year(info), \ 386 TAM3517_week_of_year(info), \ 387 TAM3517_sequence_number(info)); \ 388 printf("Rev: TN%u %u.%u\n", \ 389 TAM3517_revision_tn(info), \ 390 TAM3517_revision_major(info), \ 391 TAM3517_revision_fixed(info)); \ 392 } while (0) 393 394 #endif 395 396 #endif /* __TAM3517_H */ 397