1 /* 2 * Copyright (C) 2011 3 * Stefano Babic, DENX Software Engineering, sbabic@denx.de. 4 * 5 * Copyright (C) 2009 TechNexion Ltd. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __TAM3517_H 11 #define __TAM3517_H 12 13 /* 14 * High Level Configuration Options 15 */ 16 #define CONFIG_OMAP /* in a TI OMAP core */ 17 #define CONFIG_OMAP_GPIO 18 #define CONFIG_OMAP_COMMON 19 #define CONFIG_SYS_GENERIC_BOARD 20 /* Common ARM Erratas */ 21 #define CONFIG_ARM_ERRATA_454179 22 #define CONFIG_ARM_ERRATA_430973 23 #define CONFIG_ARM_ERRATA_621766 24 25 #define CONFIG_SYS_TEXT_BASE 0x80008000 26 27 #define CONFIG_SYS_CACHELINE_SIZE 64 28 29 #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ 30 31 #include <asm/arch/cpu.h> /* get chip and board defs */ 32 #include <asm/arch/omap.h> 33 34 /* 35 * Display CPU and Board information 36 */ 37 #define CONFIG_DISPLAY_CPUINFO 38 #define CONFIG_DISPLAY_BOARDINFO 39 40 /* Clock Defines */ 41 #define V_OSCK 26000000 /* Clock output from T2 */ 42 #define V_SCLK (V_OSCK >> 1) 43 44 #define CONFIG_MISC_INIT_R 45 46 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 47 #define CONFIG_SETUP_MEMORY_TAGS 48 #define CONFIG_INITRD_TAG 49 #define CONFIG_REVISION_TAG 50 51 /* 52 * Size of malloc() pool 53 */ 54 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ 55 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \ 56 2 * 1024 * 1024) 57 /* 58 * DDR related 59 */ 60 #define CONFIG_OMAP3_MICRON_DDR /* Micron DDR */ 61 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024) 62 63 /* 64 * Hardware drivers 65 */ 66 67 /* 68 * NS16550 Configuration 69 */ 70 #define CONFIG_SYS_NS16550 71 #define CONFIG_SYS_NS16550_SERIAL 72 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 73 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 74 75 /* 76 * select serial console configuration 77 */ 78 #define CONFIG_CONS_INDEX 1 79 #define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 80 #define CONFIG_SERIAL1 /* UART1 */ 81 82 /* allow to overwrite serial and ethaddr */ 83 #define CONFIG_ENV_OVERWRITE 84 #define CONFIG_BAUDRATE 115200 85 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 86 115200} 87 #define CONFIG_MMC 88 #define CONFIG_OMAP_HSMMC 89 #define CONFIG_GENERIC_MMC 90 #define CONFIG_DOS_PARTITION 91 92 /* EHCI */ 93 #define CONFIG_OMAP3_GPIO_5 94 #define CONFIG_USB_EHCI 95 #define CONFIG_USB_EHCI_OMAP 96 #define CONFIG_USB_ULPI 97 #define CONFIG_USB_ULPI_VIEWPORT_OMAP 98 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25 99 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 100 #define CONFIG_USB_STORAGE 101 102 /* commands to include */ 103 #include <config_cmd_default.h> 104 105 #define CONFIG_CMD_CACHE 106 #define CONFIG_CMD_DHCP 107 #define CONFIG_CMD_EXT2 /* EXT2 Support */ 108 #define CONFIG_CMD_FAT /* FAT support */ 109 #define CONFIG_CMD_GPIO 110 #define CONFIG_CMD_I2C /* I2C serial bus support */ 111 #define CONFIG_CMD_MII 112 #define CONFIG_CMD_MMC /* MMC support */ 113 #define CONFIG_CMD_NFS 114 #define CONFIG_CMD_NAND /* NAND support */ 115 #define CONFIG_CMD_PING 116 #define CONFIG_CMD_USB 117 #define CONFIG_CMD_EEPROM 118 119 #undef CONFIG_CMD_FLASH /* only NAND on the SOM */ 120 #undef CONFIG_CMD_IMLS 121 122 #define CONFIG_SYS_NO_FLASH 123 #define CONFIG_SYS_I2C 124 #define CONFIG_SYS_OMAP24_I2C_SPEED 400000 125 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 126 #define CONFIG_SYS_I2C_OMAP34XX 127 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ 128 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ 129 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 130 131 /* 132 * Board NAND Info. 133 */ 134 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 135 /* to access */ 136 /* nand at CS0 */ 137 138 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ 139 /* NAND devices */ 140 141 #define CONFIG_AUTO_COMPLETE 142 143 /* 144 * Miscellaneous configurable options 145 */ 146 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 147 #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ 148 #define CONFIG_CMDLINE_EDITING 149 #define CONFIG_AUTO_COMPLETE 150 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 151 152 /* Print Buffer Size */ 153 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 154 sizeof(CONFIG_SYS_PROMPT) + 16) 155 #define CONFIG_SYS_MAXARGS 32 /* max number of command */ 156 /* args */ 157 /* Boot Argument Buffer Size */ 158 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 159 /* memtest works on */ 160 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) 161 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 162 0x01F00000) /* 31MB */ 163 164 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ 165 /* address */ 166 167 /* 168 * AM3517 has 12 GP timers, they can be driven by the system clock 169 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 170 * This rate is divided by a local divisor. 171 */ 172 #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 173 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 174 175 /* 176 * Physical Memory Map 177 */ 178 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 179 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 180 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 181 182 /* 183 * FLASH and environment organization 184 */ 185 186 /* **** PISMO SUPPORT *** */ 187 #define CONFIG_NAND 188 #define CONFIG_NAND_OMAP_GPMC 189 #define CONFIG_ENV_IS_IN_NAND 190 #define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */ 191 192 /* Redundant Environment */ 193 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ 194 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 195 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 196 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 197 2 * CONFIG_SYS_ENV_SECT_SIZE) 198 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 199 200 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 201 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 202 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 203 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 204 CONFIG_SYS_INIT_RAM_SIZE - \ 205 GENERATED_GBL_DATA_SIZE) 206 207 /* 208 * ethernet support, EMAC 209 * 210 */ 211 #define CONFIG_DRIVER_TI_EMAC 212 #define CONFIG_DRIVER_TI_EMAC_USE_RMII 213 #define CONFIG_MII 214 #define CONFIG_EMAC_MDIO_PHY_NUM 0 215 #define CONFIG_BOOTP_DNS 216 #define CONFIG_BOOTP_DNS2 217 #define CONFIG_BOOTP_SEND_HOSTNAME 218 #define CONFIG_NET_RETRY_COUNT 10 219 220 /* Defines for SPL */ 221 #define CONFIG_SPL_FRAMEWORK 222 #define CONFIG_SPL_BOARD_INIT 223 #define CONFIG_SPL_CONSOLE 224 #define CONFIG_SPL_NAND_SIMPLE 225 #define CONFIG_SPL_NAND_SOFTECC 226 #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */ 227 228 #define CONFIG_SPL_LIBCOMMON_SUPPORT 229 #define CONFIG_SPL_LIBDISK_SUPPORT 230 #define CONFIG_SPL_I2C_SUPPORT 231 #define CONFIG_SPL_LIBGENERIC_SUPPORT 232 #define CONFIG_SPL_SERIAL_SUPPORT 233 #define CONFIG_SPL_GPIO_SUPPORT 234 #define CONFIG_SPL_POWER_SUPPORT 235 #define CONFIG_SPL_NAND_SUPPORT 236 #define CONFIG_SPL_NAND_BASE 237 #define CONFIG_SPL_NAND_DRIVERS 238 #define CONFIG_SPL_NAND_ECC 239 #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" 240 241 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ 242 #define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ 243 244 #define CONFIG_SYS_SPL_MALLOC_START 0x8f000000 245 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 246 #define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */ 247 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 248 249 /* NAND boot config */ 250 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16 251 #define CONFIG_SYS_NAND_PAGE_COUNT 64 252 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 253 #define CONFIG_SYS_NAND_OOBSIZE 64 254 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 255 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 256 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 257 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\ 258 48, 49, 50, 51, 52, 53, 54, 55,\ 259 56, 57, 58, 59, 60, 61, 62, 63} 260 #define CONFIG_SYS_NAND_ECCSIZE 256 261 #define CONFIG_SYS_NAND_ECCBYTES 3 262 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW 263 264 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 265 266 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 267 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000 268 269 #define CONFIG_OF_LIBFDT 270 #define CONFIG_FIT 271 #define CONFIG_CMD_UBI 272 #define CONFIG_CMD_UBIFS 273 #define CONFIG_RBTREE 274 #define CONFIG_LZO 275 #define CONFIG_MTD_PARTITIONS 276 #define CONFIG_MTD_DEVICE 277 #define CONFIG_CMD_MTDPARTS 278 279 /* Setup MTD for NAND on the SOM */ 280 #define MTDIDS_DEFAULT "nand0=omap2-nand.0" 281 #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO)," \ 282 "1m(u-boot),256k(env1)," \ 283 "256k(env2),6m(kernel),-(rootfs)" 284 285 #define CONFIG_TAM3517_SETTINGS \ 286 "netdev=eth0\0" \ 287 "nandargs=setenv bootargs root=${nandroot} " \ 288 "rootfstype=${nandrootfstype}\0" \ 289 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 290 "nfsroot=${serverip}:${rootpath}\0" \ 291 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 292 "addip_sta=setenv bootargs ${bootargs} " \ 293 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 294 ":${hostname}:${netdev}:off panic=1\0" \ 295 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ 296 "addip=if test -n ${ipdyn};then run addip_dyn;" \ 297 "else run addip_sta;fi\0" \ 298 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 299 "addtty=setenv bootargs ${bootargs}" \ 300 " console=ttyO0,${baudrate}\0" \ 301 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ 302 "loadaddr=82000000\0" \ 303 "kernel_addr_r=82000000\0" \ 304 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \ 305 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \ 306 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 307 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 308 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 309 "bootm ${kernel_addr}\0" \ 310 "nandboot=run nandargs addip addtty addmtd addmisc;" \ 311 "nand read ${kernel_addr_r} kernel\0" \ 312 "bootm ${kernel_addr_r}\0" \ 313 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 314 "run nfsargs addip addtty addmtd addmisc;" \ 315 "bootm ${kernel_addr_r}\0" \ 316 "net_self=if run net_self_load;then " \ 317 "run ramargs addip addtty addmtd addmisc;" \ 318 "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \ 319 "else echo Images not loades;fi\0" \ 320 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \ 321 "load=tftp ${loadaddr} ${u-boot}\0" \ 322 "loadmlo=tftp ${loadaddr} ${mlo}\0" \ 323 "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \ 324 "uboot_addr=0x80000\0" \ 325 "update=nandecc sw;nand erase ${uboot_addr} 100000;" \ 326 "nand write ${loadaddr} ${uboot_addr} 80000\0" \ 327 "updatemlo=nandecc hw;nand erase 0 20000;" \ 328 "nand write ${loadaddr} 0 20000\0" \ 329 "upd=if run load;then echo Updating u-boot;if run update;" \ 330 "then echo U-Boot updated;" \ 331 "else echo Error updating u-boot !;" \ 332 "echo Board without bootloader !!;" \ 333 "fi;" \ 334 "else echo U-Boot not downloaded..exiting;fi\0" \ 335 336 337 /* 338 * this is common code for all TAM3517 boards. 339 * MAC address is stored from manufacturer in 340 * I2C EEPROM 341 */ 342 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) 343 /* 344 * The I2C EEPROM on the TAM3517 contains 345 * mac address and production data 346 */ 347 struct tam3517_module_info { 348 char customer[48]; 349 char product[48]; 350 351 /* 352 * bit 0~47 : sequence number 353 * bit 48~55 : week of year, from 0. 354 * bit 56~63 : year 355 */ 356 unsigned long long sequence_number; 357 358 /* 359 * bit 0~7 : revision fixed 360 * bit 8~15 : revision major 361 * bit 16~31 : TNxxx 362 */ 363 unsigned int revision; 364 unsigned char eth_addr[4][8]; 365 unsigned char _rev[100]; 366 }; 367 368 #define TAM3517_READ_EEPROM(info, ret) \ 369 do { \ 370 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \ 371 if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ 372 (void *)info, sizeof(*info))) \ 373 ret = 1; \ 374 else \ 375 ret = 0; \ 376 } while (0) 377 378 #define TAM3517_READ_MAC_FROM_EEPROM(info) \ 379 do { \ 380 char buf[80], ethname[20]; \ 381 int i; \ 382 memset(buf, 0, sizeof(buf)); \ 383 for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \ 384 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \ 385 (info)->eth_addr[i][5], \ 386 (info)->eth_addr[i][4], \ 387 (info)->eth_addr[i][3], \ 388 (info)->eth_addr[i][2], \ 389 (info)->eth_addr[i][1], \ 390 (info)->eth_addr[i][0]); \ 391 \ 392 if (i) \ 393 sprintf(ethname, "eth%daddr", i); \ 394 else \ 395 sprintf(ethname, "ethaddr"); \ 396 printf("Setting %s from EEPROM with %s\n", ethname, buf);\ 397 setenv(ethname, buf); \ 398 } \ 399 } while (0) 400 401 /* The following macros are taken from Technexion's documentation */ 402 #define TAM3517_sequence_number(info) \ 403 ((info)->sequence_number % 0x1000000000000LL) 404 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100) 405 #define TAM3517_year(info) ((info)->sequence_number >> 56) 406 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100) 407 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100) 408 #define TAM3517_revision_tn(info) ((info)->revision >> 16) 409 410 #define TAM3517_PRINT_SOM_INFO(info) \ 411 do { \ 412 printf("Vendor:%s\n", (info)->customer); \ 413 printf("SOM: %s\n", (info)->product); \ 414 printf("SeqNr: %02llu%02llu%012llu\n", \ 415 TAM3517_year(info), \ 416 TAM3517_week_of_year(info), \ 417 TAM3517_sequence_number(info)); \ 418 printf("Rev: TN%u %u.%u\n", \ 419 TAM3517_revision_tn(info), \ 420 TAM3517_revision_major(info), \ 421 TAM3517_revision_fixed(info)); \ 422 } while (0) 423 424 #endif 425 426 #endif /* __TAM3517_H */ 427