1 /* 2 * Copyright (C) 2011 3 * Stefano Babic, DENX Software Engineering, sbabic@denx.de. 4 * 5 * Copyright (C) 2009 TechNexion Ltd. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __TAM3517_H 11 #define __TAM3517_H 12 13 /* 14 * High Level Configuration Options 15 */ 16 #define CONFIG_OMAP /* in a TI OMAP core */ 17 #define CONFIG_OMAP34XX /* which is a 34XX */ 18 #define CONFIG_OMAP_GPIO 19 #define CONFIG_OMAP_COMMON 20 21 #define CONFIG_SYS_TEXT_BASE 0x80008000 22 23 #define CONFIG_SYS_CACHELINE_SIZE 64 24 25 #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ 26 27 #include <asm/arch/cpu.h> /* get chip and board defs */ 28 #include <asm/arch/omap3.h> 29 30 /* 31 * Display CPU and Board information 32 */ 33 #define CONFIG_DISPLAY_CPUINFO 34 #define CONFIG_DISPLAY_BOARDINFO 35 36 /* Clock Defines */ 37 #define V_OSCK 26000000 /* Clock output from T2 */ 38 #define V_SCLK (V_OSCK >> 1) 39 40 #define CONFIG_MISC_INIT_R 41 42 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 43 #define CONFIG_SETUP_MEMORY_TAGS 44 #define CONFIG_INITRD_TAG 45 #define CONFIG_REVISION_TAG 46 47 /* 48 * Size of malloc() pool 49 */ 50 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ 51 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \ 52 2 * 1024 * 1024) 53 /* 54 * DDR related 55 */ 56 #define CONFIG_OMAP3_MICRON_DDR /* Micron DDR */ 57 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024) 58 59 /* 60 * Hardware drivers 61 */ 62 63 /* 64 * NS16550 Configuration 65 */ 66 #define CONFIG_SYS_NS16550 67 #define CONFIG_SYS_NS16550_SERIAL 68 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 69 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 70 71 /* 72 * select serial console configuration 73 */ 74 #define CONFIG_CONS_INDEX 1 75 #define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 76 #define CONFIG_SERIAL1 /* UART1 */ 77 78 /* allow to overwrite serial and ethaddr */ 79 #define CONFIG_ENV_OVERWRITE 80 #define CONFIG_BAUDRATE 115200 81 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 82 115200} 83 #define CONFIG_MMC 84 #define CONFIG_OMAP_HSMMC 85 #define CONFIG_GENERIC_MMC 86 #define CONFIG_DOS_PARTITION 87 88 /* EHCI */ 89 #define CONFIG_OMAP3_GPIO_5 90 #define CONFIG_USB_EHCI 91 #define CONFIG_USB_EHCI_OMAP 92 #define CONFIG_USB_ULPI 93 #define CONFIG_USB_ULPI_VIEWPORT_OMAP 94 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25 95 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 96 #define CONFIG_USB_STORAGE 97 98 /* commands to include */ 99 #include <config_cmd_default.h> 100 101 #define CONFIG_CMD_CACHE 102 #define CONFIG_CMD_DHCP 103 #define CONFIG_CMD_EXT2 /* EXT2 Support */ 104 #define CONFIG_CMD_FAT /* FAT support */ 105 #define CONFIG_CMD_GPIO 106 #define CONFIG_CMD_I2C /* I2C serial bus support */ 107 #define CONFIG_CMD_MII 108 #define CONFIG_CMD_MMC /* MMC support */ 109 #define CONFIG_CMD_NET 110 #define CONFIG_CMD_NFS 111 #define CONFIG_CMD_NAND /* NAND support */ 112 #define CONFIG_CMD_PING 113 #define CONFIG_CMD_USB 114 #define CONFIG_CMD_EEPROM 115 116 #undef CONFIG_CMD_FLASH /* only NAND on the SOM */ 117 #undef CONFIG_CMD_IMLS 118 119 #define CONFIG_SYS_NO_FLASH 120 #define CONFIG_HARD_I2C 121 #define CONFIG_SYS_I2C_SPEED 400000 122 #define CONFIG_SYS_I2C_SLAVE 1 123 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ 124 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ 125 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 126 #define CONFIG_DRIVER_OMAP34XX_I2C 127 128 129 /* 130 * Board NAND Info. 131 */ 132 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 133 /* to access */ 134 /* nand at CS0 */ 135 136 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ 137 /* NAND devices */ 138 139 #define CONFIG_AUTO_COMPLETE 140 141 /* 142 * Miscellaneous configurable options 143 */ 144 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 145 #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ 146 #define CONFIG_CMDLINE_EDITING 147 #define CONFIG_AUTO_COMPLETE 148 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 149 150 /* Print Buffer Size */ 151 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 152 sizeof(CONFIG_SYS_PROMPT) + 16) 153 #define CONFIG_SYS_MAXARGS 32 /* max number of command */ 154 /* args */ 155 /* Boot Argument Buffer Size */ 156 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 157 /* memtest works on */ 158 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) 159 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 160 0x01F00000) /* 31MB */ 161 162 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ 163 /* address */ 164 165 /* 166 * AM3517 has 12 GP timers, they can be driven by the system clock 167 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 168 * This rate is divided by a local divisor. 169 */ 170 #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 171 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 172 #define CONFIG_SYS_HZ 1000 173 174 /* 175 * Physical Memory Map 176 */ 177 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 178 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 179 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 180 181 /* 182 * FLASH and environment organization 183 */ 184 185 /* **** PISMO SUPPORT *** */ 186 187 /* Configure the PISMO */ 188 #define PISMO1_NAND_SIZE GPMC_SIZE_128M 189 190 #define CONFIG_NAND_OMAP_GPMC 191 #define GPMC_NAND_ECC_LP_x16_LAYOUT 192 #define CONFIG_ENV_IS_IN_NAND 193 #define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */ 194 195 /* Redundant Environment */ 196 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ 197 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 198 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 199 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 200 2 * CONFIG_SYS_ENV_SECT_SIZE) 201 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 202 203 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 204 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 205 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 206 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 207 CONFIG_SYS_INIT_RAM_SIZE - \ 208 GENERATED_GBL_DATA_SIZE) 209 210 /* 211 * ethernet support, EMAC 212 * 213 */ 214 #define CONFIG_DRIVER_TI_EMAC 215 #define CONFIG_DRIVER_TI_EMAC_USE_RMII 216 #define CONFIG_MII 217 #define CONFIG_EMAC_MDIO_PHY_NUM 0 218 #define CONFIG_BOOTP_DEFAULT 219 #define CONFIG_BOOTP_DNS 220 #define CONFIG_BOOTP_DNS2 221 #define CONFIG_BOOTP_SEND_HOSTNAME 222 #define CONFIG_NET_RETRY_COUNT 10 223 224 /* Defines for SPL */ 225 #define CONFIG_SPL 226 #define CONFIG_SPL_FRAMEWORK 227 #define CONFIG_SPL_BOARD_INIT 228 #define CONFIG_SPL_CONSOLE 229 #define CONFIG_SPL_NAND_SIMPLE 230 #define CONFIG_SPL_NAND_SOFTECC 231 #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */ 232 233 #define CONFIG_SPL_LIBCOMMON_SUPPORT 234 #define CONFIG_SPL_LIBDISK_SUPPORT 235 #define CONFIG_SPL_I2C_SUPPORT 236 #define CONFIG_SPL_LIBGENERIC_SUPPORT 237 #define CONFIG_SPL_SERIAL_SUPPORT 238 #define CONFIG_SPL_GPIO_SUPPORT 239 #define CONFIG_SPL_POWER_SUPPORT 240 #define CONFIG_SPL_NAND_SUPPORT 241 #define CONFIG_SPL_NAND_BASE 242 #define CONFIG_SPL_NAND_DRIVERS 243 #define CONFIG_SPL_NAND_ECC 244 #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" 245 246 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ 247 #define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ 248 #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK 249 250 #define CONFIG_SYS_SPL_MALLOC_START 0x8f000000 251 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 252 #define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */ 253 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 254 255 /* NAND boot config */ 256 #define CONFIG_SYS_NAND_PAGE_COUNT 64 257 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 258 #define CONFIG_SYS_NAND_OOBSIZE 64 259 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 260 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 261 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 262 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\ 263 48, 49, 50, 51, 52, 53, 54, 55,\ 264 56, 57, 58, 59, 60, 61, 62, 63} 265 #define CONFIG_SYS_NAND_ECCSIZE 256 266 #define CONFIG_SYS_NAND_ECCBYTES 3 267 268 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 269 270 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 271 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000 272 273 #define CONFIG_OF_LIBFDT 274 #define CONFIG_FIT 275 #define CONFIG_CMD_UBI 276 #define CONFIG_CMD_UBIFS 277 #define CONFIG_RBTREE 278 #define CONFIG_LZO 279 #define CONFIG_MTD_PARTITIONS 280 #define CONFIG_MTD_DEVICE 281 #define CONFIG_CMD_MTDPARTS 282 283 /* Setup MTD for NAND on the SOM */ 284 #define MTDIDS_DEFAULT "nand0=omap2-nand.0" 285 #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO)," \ 286 "1m(u-boot),256k(env1)," \ 287 "256k(env2),6m(kernel),-(rootfs)" 288 289 #define CONFIG_TAM3517_SETTINGS \ 290 "netdev=eth0\0" \ 291 "nandargs=setenv bootargs root=${nandroot} " \ 292 "rootfstype=${nandrootfstype}\0" \ 293 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 294 "nfsroot=${serverip}:${rootpath}\0" \ 295 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 296 "addip_sta=setenv bootargs ${bootargs} " \ 297 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 298 ":${hostname}:${netdev}:off panic=1\0" \ 299 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ 300 "addip=if test -n ${ipdyn};then run addip_dyn;" \ 301 "else run addip_sta;fi\0" \ 302 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 303 "addtty=setenv bootargs ${bootargs}" \ 304 " console=ttyO0,${baudrate}\0" \ 305 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ 306 "loadaddr=82000000\0" \ 307 "kernel_addr_r=82000000\0" \ 308 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \ 309 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \ 310 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 311 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 312 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 313 "bootm ${kernel_addr}\0" \ 314 "nandboot=run nandargs addip addtty addmtd addmisc;" \ 315 "nand read ${kernel_addr_r} kernel\0" \ 316 "bootm ${kernel_addr_r}\0" \ 317 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 318 "run nfsargs addip addtty addmtd addmisc;" \ 319 "bootm ${kernel_addr_r}\0" \ 320 "net_self=if run net_self_load;then " \ 321 "run ramargs addip addtty addmtd addmisc;" \ 322 "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \ 323 "else echo Images not loades;fi\0" \ 324 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \ 325 "load=tftp ${loadaddr} ${u-boot}\0" \ 326 "loadmlo=tftp ${loadaddr} ${mlo}\0" \ 327 "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \ 328 "uboot_addr=0x80000\0" \ 329 "update=nandecc sw;nand erase ${uboot_addr} 100000;" \ 330 "nand write ${loadaddr} ${uboot_addr} 80000\0" \ 331 "updatemlo=nandecc hw;nand erase 0 20000;" \ 332 "nand write ${loadaddr} 0 20000\0" \ 333 "upd=if run load;then echo Updating u-boot;if run update;" \ 334 "then echo U-Boot updated;" \ 335 "else echo Error updating u-boot !;" \ 336 "echo Board without bootloader !!;" \ 337 "fi;" \ 338 "else echo U-Boot not downloaded..exiting;fi\0" \ 339 340 341 /* 342 * this is common code for all TAM3517 boards. 343 * MAC address is stored from manufacturer in 344 * I2C EEPROM 345 */ 346 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) 347 /* 348 * The I2C EEPROM on the TAM3517 contains 349 * mac address and production data 350 */ 351 struct tam3517_module_info { 352 char customer[48]; 353 char product[48]; 354 355 /* 356 * bit 0~47 : sequence number 357 * bit 48~55 : week of year, from 0. 358 * bit 56~63 : year 359 */ 360 unsigned long long sequence_number; 361 362 /* 363 * bit 0~7 : revision fixed 364 * bit 8~15 : revision major 365 * bit 16~31 : TNxxx 366 */ 367 unsigned int revision; 368 unsigned char eth_addr[4][8]; 369 unsigned char _rev[100]; 370 }; 371 372 #define TAM3517_READ_EEPROM(info, ret) \ 373 do { \ 374 i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); \ 375 if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ 376 (void *)info, sizeof(*info))) \ 377 ret = 1; \ 378 else \ 379 ret = 0; \ 380 } while (0) 381 382 #define TAM3517_READ_MAC_FROM_EEPROM(info) \ 383 do { \ 384 char buf[80], ethname[20]; \ 385 int i; \ 386 memset(buf, 0, sizeof(buf)); \ 387 for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \ 388 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \ 389 (info)->eth_addr[i][5], \ 390 (info)->eth_addr[i][4], \ 391 (info)->eth_addr[i][3], \ 392 (info)->eth_addr[i][2], \ 393 (info)->eth_addr[i][1], \ 394 (info)->eth_addr[i][0]); \ 395 \ 396 if (i) \ 397 sprintf(ethname, "eth%daddr", i); \ 398 else \ 399 sprintf(ethname, "ethaddr"); \ 400 printf("Setting %s from EEPROM with %s\n", ethname, buf);\ 401 setenv(ethname, buf); \ 402 } \ 403 } while (0) 404 405 /* The following macros are taken from Technexion's documentation */ 406 #define TAM3517_sequence_number(info) \ 407 ((info)->sequence_number % 0x1000000000000LL) 408 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100) 409 #define TAM3517_year(info) ((info)->sequence_number >> 56) 410 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100) 411 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100) 412 #define TAM3517_revision_tn(info) ((info)->revision >> 16) 413 414 #define TAM3517_PRINT_SOM_INFO(info) \ 415 do { \ 416 printf("Vendor:%s\n", (info)->customer); \ 417 printf("SOM: %s\n", (info)->product); \ 418 printf("SeqNr: %02llu%02llu%012llu\n", \ 419 TAM3517_year(info), \ 420 TAM3517_week_of_year(info), \ 421 TAM3517_sequence_number(info)); \ 422 printf("Rev: TN%u %u.%u\n", \ 423 TAM3517_revision_tn(info), \ 424 TAM3517_revision_major(info), \ 425 TAM3517_revision_fixed(info)); \ 426 } while (0) 427 428 #endif 429 430 #endif /* __TAM3517_H */ 431