1 /* 2 * Copyright (C) 2011 3 * Stefano Babic, DENX Software Engineering, sbabic@denx.de. 4 * 5 * Copyright (C) 2009 TechNexion Ltd. 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __TAM3517_H 11 #define __TAM3517_H 12 13 /* 14 * High Level Configuration Options 15 */ 16 #define CONFIG_OMAP /* in a TI OMAP core */ 17 #define CONFIG_OMAP_GPIO 18 #define CONFIG_OMAP_COMMON 19 /* Common ARM Erratas */ 20 #define CONFIG_ARM_ERRATA_454179 21 #define CONFIG_ARM_ERRATA_430973 22 #define CONFIG_ARM_ERRATA_621766 23 24 #define CONFIG_SYS_TEXT_BASE 0x80008000 25 26 #define CONFIG_SYS_CACHELINE_SIZE 64 27 28 #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ 29 30 #include <asm/arch/cpu.h> /* get chip and board defs */ 31 #include <asm/arch/omap.h> 32 33 /* 34 * Display CPU and Board information 35 */ 36 #define CONFIG_DISPLAY_CPUINFO 37 #define CONFIG_DISPLAY_BOARDINFO 38 39 /* Clock Defines */ 40 #define V_OSCK 26000000 /* Clock output from T2 */ 41 #define V_SCLK (V_OSCK >> 1) 42 43 #define CONFIG_MISC_INIT_R 44 45 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 46 #define CONFIG_SETUP_MEMORY_TAGS 47 #define CONFIG_INITRD_TAG 48 #define CONFIG_REVISION_TAG 49 50 /* 51 * Size of malloc() pool 52 */ 53 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ 54 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \ 55 2 * 1024 * 1024) 56 /* 57 * DDR related 58 */ 59 #define CONFIG_OMAP3_MICRON_DDR /* Micron DDR */ 60 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024) 61 62 /* 63 * Hardware drivers 64 */ 65 66 /* 67 * NS16550 Configuration 68 */ 69 #define CONFIG_SYS_NS16550_SERIAL 70 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 71 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 72 73 /* 74 * select serial console configuration 75 */ 76 #define CONFIG_CONS_INDEX 1 77 #define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 78 #define CONFIG_SERIAL1 /* UART1 */ 79 80 /* allow to overwrite serial and ethaddr */ 81 #define CONFIG_ENV_OVERWRITE 82 #define CONFIG_BAUDRATE 115200 83 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 84 115200} 85 #define CONFIG_MMC 86 #define CONFIG_OMAP_HSMMC 87 #define CONFIG_GENERIC_MMC 88 #define CONFIG_DOS_PARTITION 89 90 /* EHCI */ 91 #define CONFIG_OMAP3_GPIO_5 92 #define CONFIG_USB_EHCI 93 #define CONFIG_USB_EHCI_OMAP 94 #define CONFIG_USB_ULPI 95 #define CONFIG_USB_ULPI_VIEWPORT_OMAP 96 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25 97 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 98 #define CONFIG_USB_STORAGE 99 100 /* commands to include */ 101 #define CONFIG_CMD_CACHE 102 #define CONFIG_CMD_DHCP 103 #define CONFIG_CMD_EXT2 /* EXT2 Support */ 104 #define CONFIG_CMD_FAT /* FAT support */ 105 #define CONFIG_CMD_I2C /* I2C serial bus support */ 106 #define CONFIG_CMD_MII 107 #define CONFIG_CMD_MMC /* MMC support */ 108 #define CONFIG_CMD_NAND /* NAND support */ 109 #define CONFIG_CMD_PING 110 #define CONFIG_CMD_USB 111 #define CONFIG_CMD_EEPROM 112 113 #define CONFIG_SYS_NO_FLASH 114 #define CONFIG_SYS_I2C 115 #define CONFIG_SYS_OMAP24_I2C_SPEED 400000 116 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 117 #define CONFIG_SYS_I2C_OMAP34XX 118 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ 119 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ 120 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 121 122 /* 123 * Board NAND Info. 124 */ 125 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 126 /* to access */ 127 /* nand at CS0 */ 128 129 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ 130 /* NAND devices */ 131 132 #define CONFIG_AUTO_COMPLETE 133 134 /* 135 * Miscellaneous configurable options 136 */ 137 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 138 #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ 139 #define CONFIG_CMDLINE_EDITING 140 #define CONFIG_AUTO_COMPLETE 141 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 142 143 /* Print Buffer Size */ 144 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 145 sizeof(CONFIG_SYS_PROMPT) + 16) 146 #define CONFIG_SYS_MAXARGS 32 /* max number of command */ 147 /* args */ 148 /* Boot Argument Buffer Size */ 149 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 150 /* memtest works on */ 151 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) 152 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 153 0x01F00000) /* 31MB */ 154 155 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ 156 /* address */ 157 158 /* 159 * AM3517 has 12 GP timers, they can be driven by the system clock 160 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 161 * This rate is divided by a local divisor. 162 */ 163 #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 164 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 165 166 /* 167 * Physical Memory Map 168 */ 169 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 170 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 171 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 172 173 /* 174 * FLASH and environment organization 175 */ 176 177 /* **** PISMO SUPPORT *** */ 178 #define CONFIG_NAND 179 #define CONFIG_NAND_OMAP_GPMC 180 #define CONFIG_ENV_IS_IN_NAND 181 #define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */ 182 183 /* Redundant Environment */ 184 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ 185 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 186 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 187 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 188 2 * CONFIG_SYS_ENV_SECT_SIZE) 189 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 190 191 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 192 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 193 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 194 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 195 CONFIG_SYS_INIT_RAM_SIZE - \ 196 GENERATED_GBL_DATA_SIZE) 197 198 /* 199 * ethernet support, EMAC 200 * 201 */ 202 #define CONFIG_DRIVER_TI_EMAC 203 #define CONFIG_DRIVER_TI_EMAC_USE_RMII 204 #define CONFIG_MII 205 #define CONFIG_EMAC_MDIO_PHY_NUM 0 206 #define CONFIG_BOOTP_DNS 207 #define CONFIG_BOOTP_DNS2 208 #define CONFIG_BOOTP_SEND_HOSTNAME 209 #define CONFIG_NET_RETRY_COUNT 10 210 211 /* Defines for SPL */ 212 #define CONFIG_SPL_FRAMEWORK 213 #define CONFIG_SPL_BOARD_INIT 214 #define CONFIG_SPL_CONSOLE 215 #define CONFIG_SPL_NAND_SIMPLE 216 #define CONFIG_SPL_NAND_SOFTECC 217 #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */ 218 219 #define CONFIG_SPL_LIBCOMMON_SUPPORT 220 #define CONFIG_SPL_LIBDISK_SUPPORT 221 #define CONFIG_SPL_I2C_SUPPORT 222 #define CONFIG_SPL_LIBGENERIC_SUPPORT 223 #define CONFIG_SPL_SERIAL_SUPPORT 224 #define CONFIG_SPL_GPIO_SUPPORT 225 #define CONFIG_SPL_POWER_SUPPORT 226 #define CONFIG_SPL_NAND_SUPPORT 227 #define CONFIG_SPL_NAND_BASE 228 #define CONFIG_SPL_NAND_DRIVERS 229 #define CONFIG_SPL_NAND_ECC 230 #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" 231 232 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ 233 #define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ 234 235 #define CONFIG_SYS_SPL_MALLOC_START 0x8f000000 236 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 237 #define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */ 238 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 239 240 /* NAND boot config */ 241 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT 242 #define CONFIG_SYS_NAND_PAGE_COUNT 64 243 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 244 #define CONFIG_SYS_NAND_OOBSIZE 64 245 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 246 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 247 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 248 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\ 249 48, 49, 50, 51, 52, 53, 54, 55,\ 250 56, 57, 58, 59, 60, 61, 62, 63} 251 #define CONFIG_SYS_NAND_ECCSIZE 256 252 #define CONFIG_SYS_NAND_ECCBYTES 3 253 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW 254 #define CONFIG_NAND_OMAP_GPMC_PREFETCH 255 256 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 257 258 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 259 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000 260 261 #define CONFIG_OF_LIBFDT 262 #define CONFIG_FIT 263 #define CONFIG_CMD_UBI 264 #define CONFIG_CMD_UBIFS 265 #define CONFIG_RBTREE 266 #define CONFIG_LZO 267 #define CONFIG_MTD_PARTITIONS 268 #define CONFIG_MTD_DEVICE 269 #define CONFIG_CMD_MTDPARTS 270 271 /* Setup MTD for NAND on the SOM */ 272 #define MTDIDS_DEFAULT "nand0=omap2-nand.0" 273 #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO)," \ 274 "1m(u-boot),256k(env1)," \ 275 "256k(env2),6m(kernel),-(rootfs)" 276 277 #define CONFIG_TAM3517_SETTINGS \ 278 "netdev=eth0\0" \ 279 "nandargs=setenv bootargs root=${nandroot} " \ 280 "rootfstype=${nandrootfstype}\0" \ 281 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 282 "nfsroot=${serverip}:${rootpath}\0" \ 283 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 284 "addip_sta=setenv bootargs ${bootargs} " \ 285 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 286 ":${hostname}:${netdev}:off panic=1\0" \ 287 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ 288 "addip=if test -n ${ipdyn};then run addip_dyn;" \ 289 "else run addip_sta;fi\0" \ 290 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 291 "addtty=setenv bootargs ${bootargs}" \ 292 " console=ttyO0,${baudrate}\0" \ 293 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ 294 "loadaddr=82000000\0" \ 295 "kernel_addr_r=82000000\0" \ 296 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \ 297 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \ 298 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 299 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 300 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 301 "bootm ${kernel_addr}\0" \ 302 "nandboot=run nandargs addip addtty addmtd addmisc;" \ 303 "nand read ${kernel_addr_r} kernel\0" \ 304 "bootm ${kernel_addr_r}\0" \ 305 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 306 "run nfsargs addip addtty addmtd addmisc;" \ 307 "bootm ${kernel_addr_r}\0" \ 308 "net_self=if run net_self_load;then " \ 309 "run ramargs addip addtty addmtd addmisc;" \ 310 "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \ 311 "else echo Images not loades;fi\0" \ 312 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \ 313 "load=tftp ${loadaddr} ${u-boot}\0" \ 314 "loadmlo=tftp ${loadaddr} ${mlo}\0" \ 315 "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \ 316 "uboot_addr=0x80000\0" \ 317 "update=nandecc sw;nand erase ${uboot_addr} 100000;" \ 318 "nand write ${loadaddr} ${uboot_addr} 80000\0" \ 319 "updatemlo=nandecc hw;nand erase 0 20000;" \ 320 "nand write ${loadaddr} 0 20000\0" \ 321 "upd=if run load;then echo Updating u-boot;if run update;" \ 322 "then echo U-Boot updated;" \ 323 "else echo Error updating u-boot !;" \ 324 "echo Board without bootloader !!;" \ 325 "fi;" \ 326 "else echo U-Boot not downloaded..exiting;fi\0" \ 327 328 329 /* 330 * this is common code for all TAM3517 boards. 331 * MAC address is stored from manufacturer in 332 * I2C EEPROM 333 */ 334 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) 335 /* 336 * The I2C EEPROM on the TAM3517 contains 337 * mac address and production data 338 */ 339 struct tam3517_module_info { 340 char customer[48]; 341 char product[48]; 342 343 /* 344 * bit 0~47 : sequence number 345 * bit 48~55 : week of year, from 0. 346 * bit 56~63 : year 347 */ 348 unsigned long long sequence_number; 349 350 /* 351 * bit 0~7 : revision fixed 352 * bit 8~15 : revision major 353 * bit 16~31 : TNxxx 354 */ 355 unsigned int revision; 356 unsigned char eth_addr[4][8]; 357 unsigned char _rev[100]; 358 }; 359 360 #define TAM3517_READ_EEPROM(info, ret) \ 361 do { \ 362 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \ 363 if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ 364 (void *)info, sizeof(*info))) \ 365 ret = 1; \ 366 else \ 367 ret = 0; \ 368 } while (0) 369 370 #define TAM3517_READ_MAC_FROM_EEPROM(info) \ 371 do { \ 372 char buf[80], ethname[20]; \ 373 int i; \ 374 memset(buf, 0, sizeof(buf)); \ 375 for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \ 376 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \ 377 (info)->eth_addr[i][5], \ 378 (info)->eth_addr[i][4], \ 379 (info)->eth_addr[i][3], \ 380 (info)->eth_addr[i][2], \ 381 (info)->eth_addr[i][1], \ 382 (info)->eth_addr[i][0]); \ 383 \ 384 if (i) \ 385 sprintf(ethname, "eth%daddr", i); \ 386 else \ 387 sprintf(ethname, "ethaddr"); \ 388 printf("Setting %s from EEPROM with %s\n", ethname, buf);\ 389 setenv(ethname, buf); \ 390 } \ 391 } while (0) 392 393 /* The following macros are taken from Technexion's documentation */ 394 #define TAM3517_sequence_number(info) \ 395 ((info)->sequence_number % 0x1000000000000LL) 396 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100) 397 #define TAM3517_year(info) ((info)->sequence_number >> 56) 398 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100) 399 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100) 400 #define TAM3517_revision_tn(info) ((info)->revision >> 16) 401 402 #define TAM3517_PRINT_SOM_INFO(info) \ 403 do { \ 404 printf("Vendor:%s\n", (info)->customer); \ 405 printf("SOM: %s\n", (info)->product); \ 406 printf("SeqNr: %02llu%02llu%012llu\n", \ 407 TAM3517_year(info), \ 408 TAM3517_week_of_year(info), \ 409 TAM3517_sequence_number(info)); \ 410 printf("Rev: TN%u %u.%u\n", \ 411 TAM3517_revision_tn(info), \ 412 TAM3517_revision_major(info), \ 413 TAM3517_revision_fixed(info)); \ 414 } while (0) 415 416 #endif 417 418 #endif /* __TAM3517_H */ 419