1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2011-2012 Freescale Semiconductor, Inc. 4 */ 5 6 /* 7 * Corenet DS style board configuration file 8 */ 9 #ifndef __T4QDS_H 10 #define __T4QDS_H 11 12 /* High Level Configuration Options */ 13 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 14 15 #ifndef CONFIG_RESET_VECTOR_ADDRESS 16 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 17 #endif 18 19 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 20 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 21 #define CONFIG_PCIE1 /* PCIE controller 1 */ 22 #define CONFIG_PCIE2 /* PCIE controller 2 */ 23 #define CONFIG_PCIE3 /* PCIE controller 3 */ 24 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 25 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 26 27 #define CONFIG_SYS_SRIO 28 #define CONFIG_SRIO1 /* SRIO port 1 */ 29 #define CONFIG_SRIO2 /* SRIO port 2 */ 30 31 #define CONFIG_ENV_OVERWRITE 32 33 /* 34 * These can be toggled for performance analysis, otherwise use default. 35 */ 36 #define CONFIG_SYS_CACHE_STASHING 37 #define CONFIG_BTB /* toggle branch predition */ 38 #ifdef CONFIG_DDR_ECC 39 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 40 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 41 #endif 42 43 #define CONFIG_ENABLE_36BIT_PHYS 44 45 #define CONFIG_ADDR_MAP 46 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 47 48 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 49 #define CONFIG_SYS_MEMTEST_END 0x00400000 50 51 /* 52 * Config the L3 Cache as L3 SRAM 53 */ 54 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 55 #define CONFIG_SYS_L3_SIZE (512 << 10) 56 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 57 #ifdef CONFIG_RAMBOOT_PBL 58 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 59 #endif 60 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 61 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 62 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 63 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 64 65 #define CONFIG_SYS_DCSRBAR 0xf0000000 66 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 67 68 /* 69 * DDR Setup 70 */ 71 #define CONFIG_VERY_BIG_RAM 72 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 73 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 74 75 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 76 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 77 #define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE 78 79 #define CONFIG_DDR_SPD 80 81 /* 82 * IFC Definitions 83 */ 84 #define CONFIG_SYS_FLASH_BASE 0xe0000000 85 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 86 87 #ifdef CONFIG_SPL_BUILD 88 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 89 #else 90 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 91 #endif 92 93 #define CONFIG_MISC_INIT_R 94 95 #define CONFIG_HWCONFIG 96 97 /* define to use L1 as initial stack */ 98 #define CONFIG_L1_INIT_RAM 99 #define CONFIG_SYS_INIT_RAM_LOCK 100 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 101 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 102 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 103 /* The assembler doesn't like typecast */ 104 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 105 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 106 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 107 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 108 109 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 110 GENERATED_GBL_DATA_SIZE) 111 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 112 113 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 114 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 115 116 /* Serial Port - controlled on board with jumper J8 117 * open - index 2 118 * shorted - index 1 119 */ 120 #define CONFIG_SYS_NS16550_SERIAL 121 #define CONFIG_SYS_NS16550_REG_SIZE 1 122 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 123 124 #define CONFIG_SYS_BAUDRATE_TABLE \ 125 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 126 127 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 128 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 129 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 130 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 131 132 /* I2C */ 133 #define CONFIG_SYS_I2C 134 #define CONFIG_SYS_I2C_FSL 135 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 136 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 137 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 138 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 139 140 /* 141 * RapidIO 142 */ 143 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 144 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 145 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 146 147 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 148 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 149 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 150 151 /* 152 * General PCI 153 * Memory space is mapped 1-1, but I/O space must start from 0. 154 */ 155 156 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 157 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 158 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 159 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 160 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 161 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 162 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 163 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 164 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 165 166 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 167 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 168 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 169 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 170 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 171 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 172 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 173 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 174 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 175 176 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 177 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 178 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 179 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 180 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 181 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 182 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 183 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 184 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 185 186 /* controller 4, Base address 203000 */ 187 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 188 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull 189 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */ 190 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 191 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 192 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 193 194 #ifdef CONFIG_PCI 195 #define CONFIG_PCI_INDIRECT_BRIDGE 196 197 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 198 #endif /* CONFIG_PCI */ 199 200 /* SATA */ 201 #ifdef CONFIG_FSL_SATA_V2 202 #define CONFIG_SYS_SATA_MAX_DEVICE 2 203 #define CONFIG_SATA1 204 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 205 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 206 #define CONFIG_SATA2 207 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 208 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 209 210 #define CONFIG_LBA48 211 #endif 212 213 #ifdef CONFIG_FMAN_ENET 214 #define CONFIG_MII /* MII PHY management */ 215 #define CONFIG_ETHPRIME "FM1@DTSEC1" 216 #endif 217 218 /* 219 * Environment 220 */ 221 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 222 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 223 224 /* 225 * Command line configuration. 226 */ 227 228 /* 229 * Miscellaneous configurable options 230 */ 231 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 232 233 /* 234 * For booting Linux, the board info and command line data 235 * have to be in the first 64 MB of memory, since this is 236 * the maximum mapped by the Linux kernel during initialization. 237 */ 238 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 239 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 240 241 #ifdef CONFIG_CMD_KGDB 242 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 243 #endif 244 245 /* 246 * Environment Configuration 247 */ 248 #define CONFIG_ROOTPATH "/opt/nfsroot" 249 #define CONFIG_BOOTFILE "uImage" 250 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ 251 252 /* default location for tftp and bootm */ 253 #define CONFIG_LOADADDR 1000000 254 255 #define CONFIG_HVBOOT \ 256 "setenv bootargs config-addr=0x60000000; " \ 257 "bootm 0x01000000 - 0x00f00000" 258 259 #endif /* __CONFIG_H */ 260