1 /* 2 * (C) Copyright 2012-2012 Henrik Nordstrom <henrik@henriknordstrom.net> 3 * 4 * (C) Copyright 2007-2011 5 * Allwinner Technology Co., Ltd. <www.allwinnertech.com> 6 * Tom Cubie <tangliang@allwinnertech.com> 7 * 8 * Configuration settings for the Allwinner sunxi series of boards. 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef _SUNXI_COMMON_CONFIG_H 14 #define _SUNXI_COMMON_CONFIG_H 15 16 #include <asm/arch/cpu.h> 17 #include <linux/stringify.h> 18 19 #ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT 20 /* 21 * The U-Boot workarounds bugs in the outdated buggy sunxi-3.4 kernels at the 22 * expense of restricting some features, so the regular machine id values can 23 * be used. 24 */ 25 # define CONFIG_MACH_TYPE_COMPAT_REV 0 26 #else 27 /* 28 * A compatibility guard to prevent loading outdated buggy sunxi-3.4 kernels. 29 * Only sunxi-3.4 kernels with appropriate fixes applied are able to pass 30 * beyond the machine id check. 31 */ 32 # define CONFIG_MACH_TYPE_COMPAT_REV 1 33 #endif 34 35 /* Serial & console */ 36 #define CONFIG_SYS_NS16550_SERIAL 37 /* ns16550 reg in the low bits of cpu reg */ 38 #define CONFIG_SYS_NS16550_CLK 24000000 39 #ifndef CONFIG_DM_SERIAL 40 # define CONFIG_SYS_NS16550_REG_SIZE -4 41 # define CONFIG_SYS_NS16550_COM1 SUNXI_UART0_BASE 42 # define CONFIG_SYS_NS16550_COM2 SUNXI_UART1_BASE 43 # define CONFIG_SYS_NS16550_COM3 SUNXI_UART2_BASE 44 # define CONFIG_SYS_NS16550_COM4 SUNXI_UART3_BASE 45 # define CONFIG_SYS_NS16550_COM5 SUNXI_R_UART_BASE 46 #endif 47 48 /* CPU */ 49 #define CONFIG_TIMER_CLK_FREQ 24000000 50 51 /* 52 * The DRAM Base differs between some models. We cannot use macros for the 53 * CONFIG_FOO defines which contain the DRAM base address since they end 54 * up unexpanded in include/autoconf.mk . 55 * 56 * So we have to have this #ifdef #else #endif block for these. 57 */ 58 #ifdef CONFIG_MACH_SUN9I 59 #define SDRAM_OFFSET(x) 0x2##x 60 #define CONFIG_SYS_SDRAM_BASE 0x20000000 61 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* default load address */ 62 #define CONFIG_SYS_TEXT_BASE 0x2a000000 63 /* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here 64 * since it needs to fit in with the other values. By also #defining it 65 * we get warnings if the Kconfig value mismatches. */ 66 #define CONFIG_SPL_STACK_R_ADDR 0x2fe00000 67 #define CONFIG_SPL_BSS_START_ADDR 0x2ff80000 68 #else 69 #define SDRAM_OFFSET(x) 0x4##x 70 #define CONFIG_SYS_SDRAM_BASE 0x40000000 71 #define CONFIG_SYS_LOAD_ADDR 0x42000000 /* default load address */ 72 #define CONFIG_SYS_TEXT_BASE 0x4a000000 73 /* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here 74 * since it needs to fit in with the other values. By also #defining it 75 * we get warnings if the Kconfig value mismatches. */ 76 #define CONFIG_SPL_STACK_R_ADDR 0x4fe00000 77 #define CONFIG_SPL_BSS_START_ADDR 0x4ff80000 78 #endif 79 80 #define CONFIG_SPL_BSS_MAX_SIZE 0x00080000 /* 512 KiB */ 81 82 #if defined(CONFIG_MACH_SUN9I) || defined(CONFIG_MACH_SUN50I) 83 /* 84 * The A80's A1 sram starts at 0x00010000 rather then at 0x00000000 and is 85 * slightly bigger. Note that it is possible to map the first 32 KiB of the 86 * A1 at 0x00000000 like with older SoCs by writing 0x16aa0001 to the 87 * undocumented 0x008000e0 SYS_CTRL register. Where the 16aa is a key and 88 * the 1 actually activates the mapping of the first 32 KiB to 0x00000000. 89 */ 90 #define CONFIG_SYS_INIT_RAM_ADDR 0x10000 91 #define CONFIG_SYS_INIT_RAM_SIZE 0x08000 /* FIXME: 40 KiB ? */ 92 #else 93 #define CONFIG_SYS_INIT_RAM_ADDR 0x0 94 #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* 32 KiB */ 95 #endif 96 97 #define CONFIG_SYS_INIT_SP_OFFSET \ 98 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 99 #define CONFIG_SYS_INIT_SP_ADDR \ 100 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 101 102 #define CONFIG_NR_DRAM_BANKS 1 103 #define PHYS_SDRAM_0 CONFIG_SYS_SDRAM_BASE 104 #define PHYS_SDRAM_0_SIZE 0x80000000 /* 2 GiB */ 105 106 #ifdef CONFIG_AHCI 107 #define CONFIG_LIBATA 108 #define CONFIG_SCSI_AHCI 109 #define CONFIG_SCSI_AHCI_PLAT 110 #define CONFIG_SUNXI_AHCI 111 #define CONFIG_SYS_64BIT_LBA 112 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 113 #define CONFIG_SYS_SCSI_MAX_LUN 1 114 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 115 CONFIG_SYS_SCSI_MAX_LUN) 116 #define CONFIG_SCSI 117 #endif 118 119 #define CONFIG_SETUP_MEMORY_TAGS 120 #define CONFIG_CMDLINE_TAG 121 #define CONFIG_INITRD_TAG 122 #define CONFIG_SERIAL_TAG 123 124 #ifdef CONFIG_NAND_SUNXI 125 #define CONFIG_SYS_NAND_MAX_ECCPOS 1664 126 #define CONFIG_SYS_NAND_ONFI_DETECTION 127 #define CONFIG_SYS_MAX_NAND_DEVICE 8 128 #endif 129 130 #ifdef CONFIG_SPL_SPI_SUNXI 131 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000 132 #endif 133 134 /* mmc config */ 135 #ifdef CONFIG_MMC 136 #define CONFIG_MMC_SUNXI_SLOT 0 137 #define CONFIG_ENV_IS_IN_MMC 138 #define CONFIG_SYS_MMC_ENV_DEV 0 /* first detected MMC controller */ 139 #define CONFIG_SYS_MMC_MAX_DEVICE 4 140 #endif 141 142 /* 64MB of malloc() pool */ 143 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (64 << 20)) 144 145 /* 146 * Miscellaneous configurable options 147 */ 148 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 149 #define CONFIG_SYS_PBSIZE 1024 /* Print Buffer Size */ 150 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 151 152 /* Boot Argument Buffer Size */ 153 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 154 155 /* standalone support */ 156 #define CONFIG_STANDALONE_LOAD_ADDR CONFIG_SYS_LOAD_ADDR 157 158 /* baudrate */ 159 160 /* The stack sizes are set up in start.S using the settings below */ 161 #define CONFIG_STACKSIZE (256 << 10) /* 256 KiB */ 162 163 /* FLASH and environment organization */ 164 165 #define CONFIG_SYS_MONITOR_LEN (768 << 10) /* 768 KiB */ 166 167 #define CONFIG_ENV_OFFSET (544 << 10) /* (8 + 24 + 512) KiB */ 168 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ 169 170 #define CONFIG_FAT_WRITE /* enable write access */ 171 172 #define CONFIG_SPL_FRAMEWORK 173 174 #ifndef CONFIG_ARM64 /* AArch64 FEL support is not ready yet */ 175 #define CONFIG_SPL_BOARD_LOAD_IMAGE 176 #endif 177 178 #if defined(CONFIG_MACH_SUN9I) 179 #define CONFIG_SPL_TEXT_BASE 0x10040 /* sram start+header */ 180 #define CONFIG_SPL_MAX_SIZE 0x5fc0 /* ? KiB on sun9i */ 181 #elif defined(CONFIG_MACH_SUN50I) 182 #define CONFIG_SPL_TEXT_BASE 0x10040 /* sram start+header */ 183 #define CONFIG_SPL_MAX_SIZE 0x7fc0 /* 32 KiB on sun50i */ 184 #else 185 #define CONFIG_SPL_TEXT_BASE 0x40 /* sram start+header */ 186 #define CONFIG_SPL_MAX_SIZE 0x5fc0 /* 24KB on sun4i/sun7i */ 187 #endif 188 189 #ifndef CONFIG_ARM64 190 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/sunxi/u-boot-spl.lds" 191 #endif 192 193 #define CONFIG_SPL_PAD_TO 32768 /* decimal for 'dd' */ 194 195 #if defined(CONFIG_MACH_SUN9I) || defined(CONFIG_MACH_SUN50I) 196 /* FIXME: 40 KiB instead of 32 KiB ? */ 197 #define LOW_LEVEL_SRAM_STACK 0x00018000 198 #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK 199 #else 200 /* end of 32 KiB in sram */ 201 #define LOW_LEVEL_SRAM_STACK 0x00008000 /* End of sram */ 202 #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK 203 #endif 204 205 /* I2C */ 206 #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \ 207 defined CONFIG_SY8106A_POWER 208 #endif 209 210 #if defined CONFIG_I2C0_ENABLE || defined CONFIG_I2C1_ENABLE || \ 211 defined CONFIG_I2C2_ENABLE || defined CONFIG_I2C3_ENABLE || \ 212 defined CONFIG_I2C4_ENABLE || defined CONFIG_R_I2C_ENABLE 213 #define CONFIG_SYS_I2C 214 #define CONFIG_SYS_I2C_MVTWSI 215 #define CONFIG_SYS_I2C_SPEED 400000 216 #define CONFIG_SYS_I2C_SLAVE 0x7f 217 #endif 218 219 #if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD) 220 #define CONFIG_SYS_I2C_SOFT 221 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 222 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x00 223 /* We use pin names in Kconfig and sunxi_name_to_gpio() */ 224 #define CONFIG_SOFT_I2C_GPIO_SDA soft_i2c_gpio_sda 225 #define CONFIG_SOFT_I2C_GPIO_SCL soft_i2c_gpio_scl 226 #ifndef __ASSEMBLY__ 227 extern int soft_i2c_gpio_sda; 228 extern int soft_i2c_gpio_scl; 229 #endif 230 #define CONFIG_VIDEO_LCD_I2C_BUS 0 /* The lcd panel soft i2c is bus 0 */ 231 #define CONFIG_SYS_SPD_BUS_NUM 1 /* And the axp209 i2c bus is bus 1 */ 232 #else 233 #define CONFIG_SYS_SPD_BUS_NUM 0 /* The axp209 i2c bus is bus 0 */ 234 #define CONFIG_VIDEO_LCD_I2C_BUS -1 /* NA, but necessary to compile */ 235 #endif 236 237 /* PMU */ 238 #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \ 239 defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER || \ 240 defined CONFIG_SY8106A_POWER 241 #endif 242 243 #ifndef CONFIG_CONS_INDEX 244 #define CONFIG_CONS_INDEX 1 /* UART0 */ 245 #endif 246 247 #ifdef CONFIG_REQUIRE_SERIAL_CONSOLE 248 #if CONFIG_CONS_INDEX == 1 249 #ifdef CONFIG_MACH_SUN9I 250 #define OF_STDOUT_PATH "/soc/serial@07000000:115200" 251 #else 252 #define OF_STDOUT_PATH "/soc@01c00000/serial@01c28000:115200" 253 #endif 254 #elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_MACH_SUN5I) 255 #define OF_STDOUT_PATH "/soc@01c00000/serial@01c28400:115200" 256 #elif CONFIG_CONS_INDEX == 3 && defined(CONFIG_MACH_SUN8I) 257 #define OF_STDOUT_PATH "/soc@01c00000/serial@01c28800:115200" 258 #elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_MACH_SUN8I) 259 #define OF_STDOUT_PATH "/soc@01c00000/serial@01f02800:115200" 260 #else 261 #error Unsupported console port nr. Please fix stdout-path in sunxi-common.h. 262 #endif 263 #endif /* ifdef CONFIG_REQUIRE_SERIAL_CONSOLE */ 264 265 /* GPIO */ 266 #define CONFIG_SUNXI_GPIO 267 268 #ifdef CONFIG_VIDEO 269 /* 270 * The amount of RAM to keep free at the top of RAM when relocating u-boot, 271 * to use as framebuffer. This must be a multiple of 4096. 272 */ 273 #define CONFIG_SUNXI_MAX_FB_SIZE (16 << 20) 274 275 /* Do we want to initialize a simple FB? */ 276 #define CONFIG_VIDEO_DT_SIMPLEFB 277 278 #define CONFIG_VIDEO_SUNXI 279 280 #define CONFIG_VIDEO_LOGO 281 #define CONFIG_VIDEO_STD_TIMINGS 282 #define CONFIG_I2C_EDID 283 #define VIDEO_LINE_LEN (pGD->plnSizeX) 284 285 /* allow both serial and cfb console. */ 286 /* stop x86 thinking in cfbconsole from trying to init a pc keyboard */ 287 288 #endif /* CONFIG_VIDEO */ 289 290 /* Ethernet support */ 291 #ifdef CONFIG_SUNXI_EMAC 292 #define CONFIG_PHY_ADDR 1 293 #define CONFIG_MII /* MII PHY management */ 294 #define CONFIG_PHYLIB 295 #endif 296 297 #ifdef CONFIG_SUNXI_GMAC 298 #define CONFIG_PHY_GIGE /* GMAC can use gigabit PHY */ 299 #define CONFIG_PHY_ADDR 1 300 #define CONFIG_MII /* MII PHY management */ 301 #define CONFIG_PHY_REALTEK 302 #endif 303 304 #ifdef CONFIG_USB_EHCI_HCD 305 #define CONFIG_USB_OHCI_NEW 306 #define CONFIG_USB_OHCI_SUNXI 307 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1 308 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 309 #endif 310 311 #ifdef CONFIG_USB_MUSB_SUNXI 312 #define CONFIG_USB_MUSB_PIO_ONLY 313 #endif 314 315 #ifdef CONFIG_USB_MUSB_GADGET 316 #define CONFIG_USB_FUNCTION_FASTBOOT 317 #define CONFIG_USB_FUNCTION_MASS_STORAGE 318 #endif 319 320 #ifdef CONFIG_USB_FUNCTION_FASTBOOT 321 #define CONFIG_CMD_FASTBOOT 322 #define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR 323 #define CONFIG_FASTBOOT_BUF_SIZE 0x2000000 324 #define CONFIG_ANDROID_BOOT_IMAGE 325 326 #define CONFIG_FASTBOOT_FLASH 327 328 #ifdef CONFIG_MMC 329 #define CONFIG_FASTBOOT_FLASH_MMC_DEV 0 330 #endif 331 #endif 332 333 #ifdef CONFIG_USB_FUNCTION_MASS_STORAGE 334 #endif 335 336 #ifdef CONFIG_USB_KEYBOARD 337 #define CONFIG_PREBOOT 338 #define CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE 339 #endif 340 341 #if !defined CONFIG_ENV_IS_IN_MMC && \ 342 !defined CONFIG_ENV_IS_IN_NAND && \ 343 !defined CONFIG_ENV_IS_IN_FAT && \ 344 !defined CONFIG_ENV_IS_IN_SPI_FLASH 345 #define CONFIG_ENV_IS_NOWHERE 346 #endif 347 348 #define CONFIG_MISC_INIT_R 349 350 #ifndef CONFIG_SPL_BUILD 351 #include <config_distro_defaults.h> 352 353 #ifdef CONFIG_ARM64 354 /* 355 * Boards seem to come with at least 512MB of DRAM. 356 * The kernel should go at 512K, which is the default text offset (that will 357 * be adjusted at runtime if needed). 358 * There is no compression for arm64 kernels (yet), so leave some space 359 * for really big kernels, say 256MB for now. 360 * Scripts, PXE and DTBs should go afterwards, leaving the rest for the initrd. 361 * Align the initrd to a 2MB page. 362 */ 363 #define KERNEL_ADDR_R __stringify(SDRAM_OFFSET(0080000)) 364 #define FDT_ADDR_R __stringify(SDRAM_OFFSET(FA00000)) 365 #define SCRIPT_ADDR_R __stringify(SDRAM_OFFSET(FC00000)) 366 #define PXEFILE_ADDR_R __stringify(SDRAM_OFFSET(FD00000)) 367 #define RAMDISK_ADDR_R __stringify(SDRAM_OFFSET(FE00000)) 368 369 #else 370 /* 371 * 160M RAM (256M minimum minus 64MB heap + 32MB for u-boot, stack, fb, etc. 372 * 32M uncompressed kernel, 16M compressed kernel, 1M fdt, 373 * 1M script, 1M pxe and the ramdisk at the end. 374 */ 375 376 #define KERNEL_ADDR_R __stringify(SDRAM_OFFSET(2000000)) 377 #define FDT_ADDR_R __stringify(SDRAM_OFFSET(3000000)) 378 #define SCRIPT_ADDR_R __stringify(SDRAM_OFFSET(3100000)) 379 #define PXEFILE_ADDR_R __stringify(SDRAM_OFFSET(3200000)) 380 #define RAMDISK_ADDR_R __stringify(SDRAM_OFFSET(3300000)) 381 #endif 382 383 #define MEM_LAYOUT_ENV_SETTINGS \ 384 "bootm_size=0xa000000\0" \ 385 "kernel_addr_r=" KERNEL_ADDR_R "\0" \ 386 "fdt_addr_r=" FDT_ADDR_R "\0" \ 387 "scriptaddr=" SCRIPT_ADDR_R "\0" \ 388 "pxefile_addr_r=" PXEFILE_ADDR_R "\0" \ 389 "ramdisk_addr_r=" RAMDISK_ADDR_R "\0" 390 391 #define DFU_ALT_INFO_RAM \ 392 "dfu_alt_info_ram=" \ 393 "kernel ram " KERNEL_ADDR_R " 0x1000000;" \ 394 "fdt ram " FDT_ADDR_R " 0x100000;" \ 395 "ramdisk ram " RAMDISK_ADDR_R " 0x4000000\0" 396 397 #ifdef CONFIG_MMC 398 #define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) 399 #if CONFIG_MMC_SUNXI_SLOT_EXTRA != -1 400 #define BOOT_TARGET_DEVICES_MMC_EXTRA(func) func(MMC, mmc, 1) 401 #else 402 #define BOOT_TARGET_DEVICES_MMC_EXTRA(func) 403 #endif 404 #else 405 #define BOOT_TARGET_DEVICES_MMC(func) 406 #define BOOT_TARGET_DEVICES_MMC_EXTRA(func) 407 #endif 408 409 #ifdef CONFIG_AHCI 410 #define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0) 411 #else 412 #define BOOT_TARGET_DEVICES_SCSI(func) 413 #endif 414 415 #ifdef CONFIG_USB_STORAGE 416 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) 417 #else 418 #define BOOT_TARGET_DEVICES_USB(func) 419 #endif 420 421 /* FEL boot support, auto-execute boot.scr if a script address was provided */ 422 #define BOOTENV_DEV_FEL(devtypeu, devtypel, instance) \ 423 "bootcmd_fel=" \ 424 "if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then " \ 425 "echo '(FEL boot)'; " \ 426 "source ${fel_scriptaddr}; " \ 427 "fi\0" 428 #define BOOTENV_DEV_NAME_FEL(devtypeu, devtypel, instance) \ 429 "fel " 430 431 #define BOOT_TARGET_DEVICES(func) \ 432 func(FEL, fel, na) \ 433 BOOT_TARGET_DEVICES_MMC(func) \ 434 BOOT_TARGET_DEVICES_MMC_EXTRA(func) \ 435 BOOT_TARGET_DEVICES_SCSI(func) \ 436 BOOT_TARGET_DEVICES_USB(func) \ 437 func(PXE, pxe, na) \ 438 func(DHCP, dhcp, na) 439 440 #ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT 441 #define BOOTCMD_SUNXI_COMPAT \ 442 "bootcmd_sunxi_compat=" \ 443 "setenv root /dev/mmcblk0p3 rootwait; " \ 444 "if ext2load mmc 0 0x44000000 uEnv.txt; then " \ 445 "echo Loaded environment from uEnv.txt; " \ 446 "env import -t 0x44000000 ${filesize}; " \ 447 "fi; " \ 448 "setenv bootargs console=${console} root=${root} ${extraargs}; " \ 449 "ext2load mmc 0 0x43000000 script.bin && " \ 450 "ext2load mmc 0 0x48000000 uImage && " \ 451 "bootm 0x48000000\0" 452 #else 453 #define BOOTCMD_SUNXI_COMPAT 454 #endif 455 456 #include <config_distro_bootcmd.h> 457 458 #ifdef CONFIG_USB_KEYBOARD 459 #define CONSOLE_STDIN_SETTINGS \ 460 "preboot=usb start\0" \ 461 "stdin=serial,usbkbd\0" 462 #else 463 #define CONSOLE_STDIN_SETTINGS \ 464 "stdin=serial\0" 465 #endif 466 467 #ifdef CONFIG_VIDEO 468 #define CONSOLE_STDOUT_SETTINGS \ 469 "stdout=serial,vga\0" \ 470 "stderr=serial,vga\0" 471 #else 472 #define CONSOLE_STDOUT_SETTINGS \ 473 "stdout=serial\0" \ 474 "stderr=serial\0" 475 #endif 476 477 #define CONSOLE_ENV_SETTINGS \ 478 CONSOLE_STDIN_SETTINGS \ 479 CONSOLE_STDOUT_SETTINGS 480 481 #define CONFIG_EXTRA_ENV_SETTINGS \ 482 CONSOLE_ENV_SETTINGS \ 483 MEM_LAYOUT_ENV_SETTINGS \ 484 DFU_ALT_INFO_RAM \ 485 "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ 486 "console=ttyS0,115200\0" \ 487 BOOTCMD_SUNXI_COMPAT \ 488 BOOTENV 489 490 #else /* ifndef CONFIG_SPL_BUILD */ 491 #define CONFIG_EXTRA_ENV_SETTINGS 492 #endif 493 494 #endif /* _SUNXI_COMMON_CONFIG_H */ 495