1 /* 2 * (C) Copyright 2014 3 * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de 4 * 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 #define CONFIG_E300 1 /* E300 family */ 16 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 17 #define CONFIG_MPC830x 1 /* MPC830x family */ 18 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 19 #define CONFIG_STRIDER 1 /* STRIDER board specific */ 20 21 #define CONFIG_SYS_TEXT_BASE 0xFE000000 22 23 #define CONFIG_BOARD_EARLY_INIT_F 24 #define CONFIG_BOARD_EARLY_INIT_R 25 #define CONFIG_LAST_STAGE_INIT 26 27 #define CONFIG_MMC 28 #define CONFIG_FSL_ESDHC 29 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR 30 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 31 32 #define CONFIG_GENERIC_MMC 33 #define CONFIG_DOS_PARTITION 34 35 #define CONFIG_SYS_ALT_MEMTEST 36 37 #define CONFIG_CMD_FPGAD 38 #define CONFIG_CMD_IOLOOP 39 40 /* 41 * System Clock Setup 42 */ 43 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 44 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 45 46 /* 47 * Hardware Reset Configuration Word 48 * if CLKIN is 66.66MHz, then 49 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 50 * We choose the A type silicon as default, so the core is 400Mhz. 51 */ 52 #define CONFIG_SYS_HRCW_LOW (\ 53 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 54 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 55 HRCWL_SVCOD_DIV_2 |\ 56 HRCWL_CSB_TO_CLKIN_4X1 |\ 57 HRCWL_CORE_TO_CSB_3X1) 58 /* 59 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 60 * in 8308's HRCWH according to the manual, but original Freescale's 61 * code has them and I've expirienced some problems using the board 62 * with BDI3000 attached when I've tried to set these bits to zero 63 * (UART doesn't work after the 'reset run' command). 64 */ 65 #define CONFIG_SYS_HRCW_HIGH (\ 66 HRCWH_PCI_HOST |\ 67 HRCWH_PCI1_ARBITER_ENABLE |\ 68 HRCWH_CORE_ENABLE |\ 69 HRCWH_FROM_0XFFF00100 |\ 70 HRCWH_BOOTSEQ_DISABLE |\ 71 HRCWH_SW_WATCHDOG_DISABLE |\ 72 HRCWH_ROM_LOC_LOCAL_16BIT |\ 73 HRCWH_RL_EXT_LEGACY |\ 74 HRCWH_TSEC1M_IN_MII |\ 75 HRCWH_TSEC2M_IN_RGMII |\ 76 HRCWH_BIG_ENDIAN) 77 78 /* 79 * System IO Config 80 */ 81 #define CONFIG_SYS_SICRH (\ 82 SICRH_ESDHC_A_SD |\ 83 SICRH_ESDHC_B_SD |\ 84 SICRH_ESDHC_C_SD |\ 85 SICRH_GPIO_A_GPIO |\ 86 SICRH_GPIO_B_GPIO |\ 87 SICRH_IEEE1588_A_GPIO |\ 88 SICRH_USB |\ 89 SICRH_GTM_GPIO |\ 90 SICRH_IEEE1588_B_GPIO |\ 91 SICRH_ETSEC2_GPIO |\ 92 SICRH_GPIOSEL_1 |\ 93 SICRH_TMROBI_V3P3 |\ 94 SICRH_TSOBI1_V2P5 |\ 95 SICRH_TSOBI2_V2P5) /* 0x0037f103 */ 96 #define CONFIG_SYS_SICRL (\ 97 SICRL_SPI_PF0 |\ 98 SICRL_UART_PF0 |\ 99 SICRL_IRQ_PF0 |\ 100 SICRL_I2C2_PF0 |\ 101 SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ 102 103 /* 104 * IMMR new address 105 */ 106 #define CONFIG_SYS_IMMR 0xE0000000 107 108 /* 109 * SERDES 110 */ 111 #define CONFIG_FSL_SERDES 112 #define CONFIG_FSL_SERDES1 0xe3000 113 114 /* 115 * Arbiter Setup 116 */ 117 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 118 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 119 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 120 121 /* 122 * DDR Setup 123 */ 124 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 125 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 126 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 127 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 128 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 129 | DDRCDR_PZ_LOZ \ 130 | DDRCDR_NZ_LOZ \ 131 | DDRCDR_ODT \ 132 | DDRCDR_Q_DRN) 133 /* 0x7b880001 */ 134 /* 135 * Manually set up DDR parameters 136 * consist of one chip NT5TU64M16HG from NANYA 137 */ 138 139 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 140 141 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 142 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 143 | CSCONFIG_ODT_RD_NEVER \ 144 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 145 | CSCONFIG_BANK_BIT_3 \ 146 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 147 /* 0x80010102 */ 148 #define CONFIG_SYS_DDR_TIMING_3 0 149 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 150 | (0 << TIMING_CFG0_WRT_SHIFT) \ 151 | (0 << TIMING_CFG0_RRT_SHIFT) \ 152 | (0 << TIMING_CFG0_WWT_SHIFT) \ 153 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 154 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 155 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 156 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 157 /* 0x00260802 */ 158 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 159 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 160 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 161 | (7 << TIMING_CFG1_CASLAT_SHIFT) \ 162 | (9 << TIMING_CFG1_REFREC_SHIFT) \ 163 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 164 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 165 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 166 /* 0x26279222 */ 167 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 168 | (4 << TIMING_CFG2_CPO_SHIFT) \ 169 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 170 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 171 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 172 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 173 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 174 /* 0x021848c5 */ 175 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ 176 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 177 /* 0x08240100 */ 178 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 179 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 180 | SDRAM_CFG_DBW_16) 181 /* 0x43100000 */ 182 183 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 184 #define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ 185 | (0x0242 << SDRAM_MODE_SD_SHIFT)) 186 /* ODT 150ohm CL=4, AL=0 on SDRAM */ 187 #define CONFIG_SYS_DDR_MODE2 0x00000000 188 189 /* 190 * Memory test 191 */ 192 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 193 #define CONFIG_SYS_MEMTEST_END 0x07f00000 194 195 /* 196 * The reserved memory 197 */ 198 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 199 200 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 201 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 202 203 /* 204 * Initial RAM Base Address Setup 205 */ 206 #define CONFIG_SYS_INIT_RAM_LOCK 1 207 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 208 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 209 #define CONFIG_SYS_GBL_DATA_OFFSET \ 210 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 211 212 /* 213 * Local Bus Configuration & Clock Setup 214 */ 215 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 216 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 217 #define CONFIG_SYS_LBC_LBCR 0x00040000 218 219 /* 220 * FLASH on the Local Bus 221 */ 222 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 223 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 224 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 225 #define CONFIG_FLASH_CFI_LEGACY 226 #define CONFIG_SYS_FLASH_LEGACY_512Kx16 227 228 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 229 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ 230 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 231 232 /* Window base at flash base */ 233 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 234 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 235 236 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 237 | BR_PS_16 /* 16 bit port */ \ 238 | BR_MS_GPCM /* MSEL = GPCM */ \ 239 | BR_V) /* valid */ 240 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 241 | OR_UPM_XAM \ 242 | OR_GPCM_CSNT \ 243 | OR_GPCM_ACS_DIV2 \ 244 | OR_GPCM_XACS \ 245 | OR_GPCM_SCY_15 \ 246 | OR_GPCM_TRLX_SET \ 247 | OR_GPCM_EHTR_SET) 248 249 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 250 #define CONFIG_SYS_MAX_FLASH_SECT 135 251 252 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 253 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 254 255 /* 256 * FPGA 257 */ 258 #define CONFIG_SYS_FPGA0_BASE 0xE0600000 259 #define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ 260 261 /* Window base at FPGA base */ 262 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE 263 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) 264 265 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ 266 | BR_PS_16 /* 16 bit port */ \ 267 | BR_MS_GPCM /* MSEL = GPCM */ \ 268 | BR_V) /* valid */ 269 270 #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ 271 | OR_UPM_XAM \ 272 | OR_GPCM_CSNT \ 273 | OR_GPCM_SCY_5 \ 274 | OR_GPCM_TRLX_CLEAR \ 275 | OR_GPCM_EHTR_CLEAR) 276 277 #define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE 278 #define CONFIG_SYS_FPGA_DONE(k) 0x0010 279 280 #define CONFIG_SYS_FPGA_COUNT 1 281 282 #define CONFIG_SYS_MCLINK_MAX 3 283 284 #define CONFIG_SYS_FPGA_PTR \ 285 { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } 286 287 #define CONFIG_SYS_FPGA_NO_RFL_HI 288 289 /* 290 * Serial Port 291 */ 292 #define CONFIG_CONS_INDEX 2 293 #define CONFIG_SYS_NS16550_SERIAL 294 #define CONFIG_SYS_NS16550_REG_SIZE 1 295 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 296 297 #define CONFIG_SYS_BAUDRATE_TABLE \ 298 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 299 300 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 301 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 302 303 /* Pass open firmware flat tree */ 304 305 /* I2C */ 306 #define CONFIG_SYS_I2C 307 #define CONFIG_SYS_I2C_FSL 308 #define CONFIG_SYS_FSL_I2C_SPEED 400000 309 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 310 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 311 312 #define CONFIG_PCA953X /* NXP PCA9554 */ 313 #define CONFIG_CMD_PCA953X 314 #define CONFIG_CMD_PCA953X_INFO 315 #define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x24, 16}, {0x25, 16}, {0x26, 16}, \ 316 {0x3c, 8}, {0x3d, 8}, {0x3e, 8} } 317 318 #define CONFIG_PCA9698 /* NXP PCA9698 */ 319 320 #define CONFIG_SYS_I2C_IHS 321 #define CONFIG_SYS_I2C_IHS_CH0 322 #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 323 #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F 324 #define CONFIG_SYS_I2C_IHS_CH1 325 #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 326 #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F 327 #define CONFIG_SYS_I2C_IHS_CH2 328 #define CONFIG_SYS_I2C_IHS_SPEED_2 50000 329 #define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F 330 #define CONFIG_SYS_I2C_IHS_CH3 331 #define CONFIG_SYS_I2C_IHS_SPEED_3 50000 332 #define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F 333 334 #ifdef CONFIG_STRIDER_CON_DP 335 #define CONFIG_SYS_I2C_IHS_DUAL 336 #define CONFIG_SYS_I2C_IHS_CH0_1 337 #define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000 338 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F 339 #define CONFIG_SYS_I2C_IHS_CH1_1 340 #define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000 341 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F 342 #define CONFIG_SYS_I2C_IHS_CH2_1 343 #define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000 344 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F 345 #define CONFIG_SYS_I2C_IHS_CH3_1 346 #define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000 347 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F 348 #endif 349 350 /* 351 * Software (bit-bang) I2C driver configuration 352 */ 353 #define CONFIG_SYS_I2C_SOFT 354 #define CONFIG_SOFT_I2C_READ_REPEATED_START 355 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 356 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F 357 #define I2C_SOFT_DECLARATIONS2 358 #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 359 #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F 360 #define I2C_SOFT_DECLARATIONS3 361 #define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 362 #define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F 363 #define I2C_SOFT_DECLARATIONS4 364 #define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 365 #define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F 366 #if defined(CONFIG_STRIDER_CON) || defined(CONFIG_STRIDER_CON_DP) 367 #define I2C_SOFT_DECLARATIONS5 368 #define CONFIG_SYS_I2C_SOFT_SPEED_5 50000 369 #define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F 370 #define I2C_SOFT_DECLARATIONS6 371 #define CONFIG_SYS_I2C_SOFT_SPEED_6 50000 372 #define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F 373 #define I2C_SOFT_DECLARATIONS7 374 #define CONFIG_SYS_I2C_SOFT_SPEED_7 50000 375 #define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F 376 #define I2C_SOFT_DECLARATIONS8 377 #define CONFIG_SYS_I2C_SOFT_SPEED_8 50000 378 #define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F 379 #endif 380 #ifdef CONFIG_STRIDER_CON_DP 381 #define I2C_SOFT_DECLARATIONS9 382 #define CONFIG_SYS_I2C_SOFT_SPEED_9 50000 383 #define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F 384 #define I2C_SOFT_DECLARATIONS10 385 #define CONFIG_SYS_I2C_SOFT_SPEED_10 50000 386 #define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F 387 #define I2C_SOFT_DECLARATIONS11 388 #define CONFIG_SYS_I2C_SOFT_SPEED_11 50000 389 #define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F 390 #define I2C_SOFT_DECLARATIONS12 391 #define CONFIG_SYS_I2C_SOFT_SPEED_12 50000 392 #define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F 393 #endif 394 395 #ifdef CONFIG_STRIDER_CON 396 #define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8} 397 #define CONFIG_SYS_CH7301_I2C {5, 6, 7, 8} 398 #define CONFIG_SYS_ADV7611_I2C {5, 6, 7, 8} 399 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 400 #define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \ 401 {12, 0x4c} } 402 #elif defined(CONFIG_STRIDER_CON_DP) 403 #define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20} 404 #define CONFIG_SYS_CH7301_I2C {1, 3, 5, 7} 405 #define CONFIG_SYS_ADV7611_I2C {1, 3, 5, 7} 406 #define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8} 407 #define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \ 408 {12, 0x4c} } 409 #elif defined(CONFIG_STRIDER_CPU_DP) 410 #define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4} 411 #define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4} 412 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 413 #define CONFIG_STRIDER_FANS { {6, 0x4c}, {7, 0x4c}, \ 414 {8, 0x4c} } 415 #else 416 #define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4} 417 #define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4} 418 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 419 #define CONFIG_STRIDER_FANS { {2, 0x18}, {3, 0x18}, \ 420 {4, 0x18} } 421 #endif 422 423 #ifndef __ASSEMBLY__ 424 void fpga_gpio_set(unsigned int bus, int pin); 425 void fpga_gpio_clear(unsigned int bus, int pin); 426 int fpga_gpio_get(unsigned int bus, int pin); 427 void fpga_control_set(unsigned int bus, int pin); 428 void fpga_control_clear(unsigned int bus, int pin); 429 #endif 430 431 #ifdef CONFIG_STRIDER_CON 432 #define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040) 433 #define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020) 434 #define I2C_FPGA_IDX ((I2C_ADAP_HWNR > 3) ? \ 435 (I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR) 436 #elif defined(CONFIG_STRIDER_CON_DP) 437 #define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200) 438 #define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100) 439 #define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4) 440 #else 441 #define I2C_SDA_GPIO 0x0040 442 #define I2C_SCL_GPIO 0x0020 443 #define I2C_FPGA_IDX I2C_ADAP_HWNR 444 #endif 445 446 #ifdef CONFIG_STRIDER_CON_DP 447 #define I2C_ACTIVE \ 448 do { \ 449 if (I2C_ADAP_HWNR > 7) \ 450 fpga_control_set(I2C_FPGA_IDX, 0x0004); \ 451 else \ 452 fpga_control_clear(I2C_FPGA_IDX, 0x0004); \ 453 } while (0) 454 #else 455 #define I2C_ACTIVE { } 456 #endif 457 458 #define I2C_TRISTATE { } 459 #define I2C_READ \ 460 (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0) 461 #define I2C_SDA(bit) \ 462 do { \ 463 if (bit) \ 464 fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 465 else \ 466 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 467 } while (0) 468 #define I2C_SCL(bit) \ 469 do { \ 470 if (bit) \ 471 fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 472 else \ 473 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 474 } while (0) 475 #define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ 476 477 /* 478 * Software (bit-bang) MII driver configuration 479 */ 480 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 481 #define CONFIG_BITBANGMII_MULTI 482 483 /* 484 * OSD Setup 485 */ 486 #define CONFIG_SYS_OSD_SCREENS 1 487 #define CONFIG_SYS_DP501_DIFFERENTIAL 488 #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ 489 490 #ifdef CONFIG_STRIDER_CON_DP 491 #define CONFIG_SYS_OSD_DH 492 #endif 493 494 /* 495 * General PCI 496 * Addresses are mapped 1-1. 497 */ 498 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 499 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 500 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 501 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 502 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 503 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 504 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 505 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 506 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 507 508 /* enable PCIE clock */ 509 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 510 511 #define CONFIG_PCI_INDIRECT_BRIDGE 512 #define CONFIG_PCIE 513 514 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 515 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 516 517 /* 518 * TSEC 519 */ 520 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 521 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 522 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 523 524 /* 525 * TSEC ethernet configuration 526 */ 527 #define CONFIG_MII 1 /* MII PHY management */ 528 #define CONFIG_TSEC1 529 #define CONFIG_TSEC1_NAME "eTSEC0" 530 #define TSEC1_PHY_ADDR 1 531 #define TSEC1_PHYIDX 0 532 #define TSEC1_FLAGS 0 533 534 /* Options are: eTSEC[0-1] */ 535 #define CONFIG_ETHPRIME "eTSEC0" 536 537 /* 538 * Environment 539 */ 540 #if 1 541 #define CONFIG_ENV_IS_IN_FLASH 1 542 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 543 CONFIG_SYS_MONITOR_LEN) 544 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 545 #define CONFIG_ENV_SIZE 0x2000 546 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 547 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 548 #else 549 #define CONFIG_ENV_IS_NOWHERE 550 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 551 #endif 552 553 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 554 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 555 556 /* 557 * Command line configuration. 558 */ 559 #define CONFIG_CMD_PCI 560 561 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 562 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 563 564 /* 565 * Miscellaneous configurable options 566 */ 567 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 568 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 569 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 570 571 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 572 573 /* Print Buffer Size */ 574 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 575 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 576 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 577 578 /* 579 * For booting Linux, the board info and command line data 580 * have to be in the first 256 MB of memory, since this is 581 * the maximum mapped by the Linux kernel during initialization. 582 */ 583 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 584 585 /* 586 * Core HID Setup 587 */ 588 #define CONFIG_SYS_HID0_INIT 0x000000000 589 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 590 HID0_ENABLE_INSTRUCTION_CACHE | \ 591 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 592 #define CONFIG_SYS_HID2 HID2_HBE 593 594 /* 595 * MMU Setup 596 */ 597 598 /* DDR: cache cacheable */ 599 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 600 BATL_MEMCOHERENCE) 601 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 602 BATU_VS | BATU_VP) 603 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 604 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 605 606 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ 607 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 608 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 609 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 610 BATU_VP) 611 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 612 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 613 614 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 615 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 616 BATL_MEMCOHERENCE) 617 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 618 BATU_VS | BATU_VP) 619 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 620 BATL_CACHEINHIBIT | \ 621 BATL_GUARDEDSTORAGE) 622 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 623 624 /* Stack in dcache: cacheable, no memory coherence */ 625 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 626 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 627 BATU_VS | BATU_VP) 628 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 629 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 630 631 /* 632 * Environment Configuration 633 */ 634 635 #define CONFIG_ENV_OVERWRITE 636 637 #if defined(CONFIG_TSEC_ENET) 638 #define CONFIG_HAS_ETH0 639 #endif 640 641 #define CONFIG_BAUDRATE 115200 642 643 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 644 645 646 #define CONFIG_HOSTNAME hrcon 647 #define CONFIG_ROOTPATH "/opt/nfsroot" 648 #define CONFIG_BOOTFILE "uImage" 649 650 #define CONFIG_PREBOOT /* enable preboot variable */ 651 652 #define CONFIG_EXTRA_ENV_SETTINGS \ 653 "netdev=eth0\0" \ 654 "consoledev=ttyS1\0" \ 655 "u-boot=u-boot.bin\0" \ 656 "kernel_addr=1000000\0" \ 657 "fdt_addr=C00000\0" \ 658 "fdtfile=hrcon.dtb\0" \ 659 "load=tftp ${loadaddr} ${u-boot}\0" \ 660 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 661 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 662 " +${filesize};cp.b ${fileaddr} " \ 663 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 664 "upd=run load update\0" \ 665 666 #define CONFIG_NFSBOOTCOMMAND \ 667 "setenv bootargs root=/dev/nfs rw " \ 668 "nfsroot=$serverip:$rootpath " \ 669 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 670 "console=$consoledev,$baudrate $othbootargs;" \ 671 "tftp ${kernel_addr} $bootfile;" \ 672 "tftp ${fdt_addr} $fdtfile;" \ 673 "bootm ${kernel_addr} - ${fdt_addr}" 674 675 #define CONFIG_MMCBOOTCOMMAND \ 676 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 677 "console=$consoledev,$baudrate $othbootargs;" \ 678 "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ 679 "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ 680 "bootm ${kernel_addr} - ${fdt_addr}" 681 682 #define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND 683 684 #endif /* __CONFIG_H */ 685