1 /* 2 * (C) Copyright 2008 3 * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. 4 * 5 * Wolfgang Denk <wd@denx.de> 6 * Copyright 2004 Freescale Semiconductor. 7 * (C) Copyright 2002,2003 Motorola,Inc. 8 * Xianghua Xiao <X.Xiao@motorola.com> 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 /* 14 * Socrates 15 */ 16 17 #ifndef __CONFIG_H 18 #define __CONFIG_H 19 20 /* High Level Configuration Options */ 21 #define CONFIG_SOCRATES 1 22 23 #define CONFIG_SYS_TEXT_BASE 0xfff80000 24 25 #define CONFIG_PCI_INDIRECT_BRIDGE 26 27 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 28 29 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ 30 #define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ 31 32 /* 33 * Only possible on E500 Version 2 or newer cores. 34 */ 35 #define CONFIG_ENABLE_36BIT_PHYS 1 36 37 /* 38 * sysclk for MPC85xx 39 * 40 * Two valid values are: 41 * 33000000 42 * 66000000 43 * 44 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz 45 * is likely the desired value here, so that is now the default. 46 * The board, however, can run at 66MHz. In any event, this value 47 * must match the settings of some switches. Details can be found 48 * in the README.mpc85xxads. 49 */ 50 51 #ifndef CONFIG_SYS_CLK_FREQ 52 #define CONFIG_SYS_CLK_FREQ 66666666 53 #endif 54 55 /* 56 * These can be toggled for performance analysis, otherwise use default. 57 */ 58 #define CONFIG_L2_CACHE /* toggle L2 cache */ 59 #define CONFIG_BTB /* toggle branch predition */ 60 61 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ 62 63 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 64 #define CONFIG_SYS_MEMTEST_START 0x00400000 65 #define CONFIG_SYS_MEMTEST_END 0x00C00000 66 67 #define CONFIG_SYS_CCSRBAR 0xE0000000 68 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 69 70 /* DDR Setup */ 71 #undef CONFIG_FSL_DDR_INTERACTIVE 72 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 73 #define CONFIG_DDR_SPD 74 75 #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 76 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 77 78 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 79 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 80 #define CONFIG_VERY_BIG_RAM 81 82 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 83 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 84 85 /* I2C addresses of SPD EEPROMs */ 86 #define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */ 87 88 #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ 89 90 /* Hardcoded values, to use instead of SPD */ 91 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f 92 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 93 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 94 #define CONFIG_SYS_DDR_TIMING_1 0x3935D322 95 #define CONFIG_SYS_DDR_TIMING_2 0x14904CC8 96 #define CONFIG_SYS_DDR_MODE 0x00480432 97 #define CONFIG_SYS_DDR_INTERVAL 0x030C0100 98 #define CONFIG_SYS_DDR_CONFIG_2 0x04400000 99 #define CONFIG_SYS_DDR_CONFIG 0xC3008000 100 #define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000 101 #define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */ 102 103 /* 104 * Flash on the LocalBus 105 */ 106 #define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ 107 108 #define CONFIG_SYS_FLASH0 0xFE000000 109 #define CONFIG_SYS_FLASH1 0xFC000000 110 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } 111 112 #define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ 113 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ 114 115 #define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */ 116 #define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */ 117 #define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */ 118 #define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */ 119 120 #define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ 121 #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/ 122 123 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 124 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ 125 #undef CONFIG_SYS_FLASH_CHECKSUM 126 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 127 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 128 129 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 130 131 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 132 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 133 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 134 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ 135 136 #define CONFIG_SYS_INIT_RAM_LOCK 1 137 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 138 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/ 139 140 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 141 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 142 143 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */ 144 #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */ 145 146 /* FPGA and NAND */ 147 #define CONFIG_SYS_FPGA_BASE 0xc0000000 148 #define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */ 149 #define CONFIG_SYS_HMI_BASE 0xc0010000 150 #define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ 151 #define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */ 152 153 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70) 154 #define CONFIG_SYS_MAX_NAND_DEVICE 1 155 #define CONFIG_CMD_NAND 156 157 /* LIME GDC */ 158 #define CONFIG_SYS_LIME_BASE 0xc8000000 159 #define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */ 160 #define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */ 161 #define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */ 162 163 #define CONFIG_VIDEO_MB862xx 164 #define CONFIG_VIDEO_MB862xx_ACCEL 165 #define CONFIG_VIDEO_LOGO 166 #define CONFIG_VIDEO_BMP_LOGO 167 #define VIDEO_FB_16BPP_PIXEL_SWAP 168 #define VIDEO_FB_16BPP_WORD_SWAP 169 #define CONFIG_SPLASH_SCREEN 170 #define CONFIG_VIDEO_BMP_GZIP 171 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ 172 173 /* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */ 174 #define CONFIG_SYS_MB862xx_CCF 0x10000 175 /* SDRAM parameter */ 176 #define CONFIG_SYS_MB862xx_MMR 0x4157BA63 177 178 /* Serial Port */ 179 180 #define CONFIG_CONS_INDEX 1 181 #define CONFIG_SYS_NS16550_SERIAL 182 #define CONFIG_SYS_NS16550_REG_SIZE 1 183 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 184 185 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 186 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 187 188 #define CONFIG_SYS_BAUDRATE_TABLE \ 189 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 190 191 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 192 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 193 194 /* 195 * I2C 196 */ 197 #define CONFIG_SYS_I2C 198 #define CONFIG_SYS_I2C_FSL 199 #define CONFIG_SYS_FSL_I2C_SPEED 102124 200 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 201 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 202 #define CONFIG_SYS_FSL_I2C2_SPEED 102124 203 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 204 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 205 206 /* I2C RTC */ 207 #define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */ 208 #define CONFIG_SYS_I2C_RTC_ADDR 0x32 /* at address 0x32 */ 209 210 /* I2C W83782G HW-Monitoring IC */ 211 #define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */ 212 213 /* I2C temp sensor */ 214 /* Socrates uses Maxim's DS75, which is compatible with LM75 */ 215 #define CONFIG_DTT_LM75 1 216 #define CONFIG_DTT_SENSORS {4} /* Sensor addresses */ 217 #define CONFIG_SYS_DTT_MAX_TEMP 125 218 #define CONFIG_SYS_DTT_LOW_TEMP -55 219 #define CONFIG_SYS_DTT_HYSTERESIS 3 220 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 221 222 /* 223 * General PCI 224 * Memory space is mapped 1-1. 225 */ 226 #define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */ 227 228 /* PCI is clocked by the external source at 33 MHz */ 229 #define CONFIG_PCI_CLK_FREQ 33000000 230 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 231 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 232 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 233 #define CONFIG_SYS_PCI1_IO_BASE 0xE2000000 234 #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE 235 #define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */ 236 237 #if defined(CONFIG_PCI) 238 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 239 #endif /* CONFIG_PCI */ 240 241 #define CONFIG_MII 1 /* MII PHY management */ 242 #define CONFIG_TSEC1 1 243 #define CONFIG_TSEC1_NAME "TSEC0" 244 #define CONFIG_TSEC3 1 245 #define CONFIG_TSEC3_NAME "TSEC1" 246 #undef CONFIG_MPC85XX_FEC 247 248 #define TSEC1_PHY_ADDR 0 249 #define TSEC3_PHY_ADDR 1 250 251 #define TSEC1_PHYIDX 0 252 #define TSEC3_PHYIDX 0 253 #define TSEC1_FLAGS TSEC_GIGABIT 254 #define TSEC3_FLAGS TSEC_GIGABIT 255 256 /* Options are: TSEC[0,1] */ 257 #define CONFIG_ETHPRIME "TSEC0" 258 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 259 260 #define CONFIG_HAS_ETH0 261 #define CONFIG_HAS_ETH1 262 263 /* 264 * Environment 265 */ 266 #define CONFIG_ENV_IS_IN_FLASH 1 267 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 268 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 269 #define CONFIG_ENV_SIZE 0x4000 270 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) 271 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 272 273 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 274 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 275 276 #define CONFIG_TIMESTAMP /* Print image info with ts */ 277 278 /* 279 * BOOTP options 280 */ 281 #define CONFIG_BOOTP_BOOTFILESIZE 282 #define CONFIG_BOOTP_BOOTPATH 283 #define CONFIG_BOOTP_GATEWAY 284 #define CONFIG_BOOTP_HOSTNAME 285 286 /* 287 * Command line configuration. 288 */ 289 #define CONFIG_CMD_DTT 290 #undef CONFIG_CMD_EEPROM 291 #define CONFIG_CMD_SDRAM 292 #define CONFIG_CMD_REGINFO 293 294 #if defined(CONFIG_PCI) 295 #define CONFIG_CMD_PCI 296 #endif 297 298 #undef CONFIG_WATCHDOG /* watchdog disabled */ 299 300 /* 301 * Miscellaneous configurable options 302 */ 303 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 304 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 305 306 #if defined(CONFIG_CMD_KGDB) 307 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 308 #else 309 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 310 #endif 311 312 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size */ 313 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 314 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 315 316 /* 317 * For booting Linux, the board info and command line data 318 * have to be in the first 8 MB of memory, since this is 319 * the maximum mapped by the Linux kernel during initialization. 320 */ 321 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 322 323 #if defined(CONFIG_CMD_KGDB) 324 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ 325 #endif 326 327 #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ 328 329 330 #define CONFIG_PREBOOT "echo;" \ 331 "echo Welcome on the ABB Socrates Board;" \ 332 "echo" 333 334 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 335 336 #define CONFIG_EXTRA_ENV_SETTINGS \ 337 "netdev=eth0\0" \ 338 "consdev=ttyS0\0" \ 339 "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \ 340 "bootfile=/home/tftp/syscon3/uImage\0" \ 341 "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \ 342 "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \ 343 "uboot_addr=FFFA0000\0" \ 344 "kernel_addr=FE000000\0" \ 345 "fdt_addr=FE1E0000\0" \ 346 "ramdisk_addr=FE200000\0" \ 347 "fdt_addr_r=B00000\0" \ 348 "kernel_addr_r=200000\0" \ 349 "ramdisk_addr_r=400000\0" \ 350 "rootpath=/opt/eldk/ppc_85xxDP\0" \ 351 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 352 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 353 "nfsroot=$serverip:$rootpath\0" \ 354 "addcons=setenv bootargs $bootargs " \ 355 "console=$consdev,$baudrate\0" \ 356 "addip=setenv bootargs $bootargs " \ 357 "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ 358 ":$hostname:$netdev:off panic=1\0" \ 359 "boot_nor=run ramargs addcons;" \ 360 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 361 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 362 "tftp ${fdt_addr_r} ${fdt_file}; " \ 363 "run nfsargs addip addcons;" \ 364 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 365 "update_uboot=tftp 100000 ${uboot_file};" \ 366 "protect off fffa0000 ffffffff;" \ 367 "era fffa0000 ffffffff;" \ 368 "cp.b 100000 fffa0000 ${filesize};" \ 369 "setenv filesize;saveenv\0" \ 370 "update_kernel=tftp 100000 ${bootfile};" \ 371 "era fe000000 fe1dffff;" \ 372 "cp.b 100000 fe000000 ${filesize};" \ 373 "setenv filesize;saveenv\0" \ 374 "update_fdt=tftp 100000 ${fdt_file};" \ 375 "era fe1e0000 fe1fffff;" \ 376 "cp.b 100000 fe1e0000 ${filesize};" \ 377 "setenv filesize;saveenv\0" \ 378 "update_initrd=tftp 100000 ${initrd_file};" \ 379 "era fe200000 fe9fffff;" \ 380 "cp.b 100000 fe200000 ${filesize};" \ 381 "setenv filesize;saveenv\0" \ 382 "clean_data=era fea00000 fff5ffff\0" \ 383 "usbargs=setenv bootargs root=/dev/sda1 rw\0" \ 384 "load_usb=usb start;" \ 385 "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \ 386 "boot_usb=run load_usb usbargs addcons;" \ 387 "bootm ${kernel_addr_r} - ${fdt_addr};" \ 388 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 389 "" 390 #define CONFIG_BOOTCOMMAND "run boot_nor" 391 392 /* pass open firmware flat tree */ 393 394 /* USB support */ 395 #define CONFIG_USB_OHCI_NEW 1 396 #define CONFIG_PCI_OHCI 1 397 #define CONFIG_PCI_OHCI_DEVNO 3 /* Number in PCI list */ 398 #define CONFIG_PCI_EHCI_DEVNO (CONFIG_PCI_OHCI_DEVNO / 2) 399 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 400 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 401 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 402 403 #endif /* __CONFIG_H */ 404