1 /* 2 * (C) Copyright 2008 3 * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. 4 * 5 * Wolfgang Denk <wd@denx.de> 6 * Copyright 2004 Freescale Semiconductor. 7 * (C) Copyright 2002,2003 Motorola,Inc. 8 * Xianghua Xiao <X.Xiao@motorola.com> 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 /* 14 * Socrates 15 */ 16 17 #ifndef __CONFIG_H 18 #define __CONFIG_H 19 20 /* High Level Configuration Options */ 21 #define CONFIG_BOOKE 1 /* BOOKE */ 22 #define CONFIG_E500 1 /* BOOKE e500 family */ 23 #define CONFIG_MPC8544 1 24 #define CONFIG_SOCRATES 1 25 #define CONFIG_DISPLAY_BOARDINFO 26 27 #define CONFIG_SYS_TEXT_BASE 0xfff80000 28 29 #define CONFIG_PCI 30 #define CONFIG_PCI_INDIRECT_BRIDGE 31 32 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 33 34 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ 35 #define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ 36 37 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 38 39 /* 40 * Only possible on E500 Version 2 or newer cores. 41 */ 42 #define CONFIG_ENABLE_36BIT_PHYS 1 43 44 /* 45 * sysclk for MPC85xx 46 * 47 * Two valid values are: 48 * 33000000 49 * 66000000 50 * 51 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz 52 * is likely the desired value here, so that is now the default. 53 * The board, however, can run at 66MHz. In any event, this value 54 * must match the settings of some switches. Details can be found 55 * in the README.mpc85xxads. 56 */ 57 58 #ifndef CONFIG_SYS_CLK_FREQ 59 #define CONFIG_SYS_CLK_FREQ 66666666 60 #endif 61 62 /* 63 * These can be toggled for performance analysis, otherwise use default. 64 */ 65 #define CONFIG_L2_CACHE /* toggle L2 cache */ 66 #define CONFIG_BTB /* toggle branch predition */ 67 68 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ 69 70 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 71 #define CONFIG_SYS_MEMTEST_START 0x00400000 72 #define CONFIG_SYS_MEMTEST_END 0x00C00000 73 74 #define CONFIG_SYS_CCSRBAR 0xE0000000 75 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 76 77 /* DDR Setup */ 78 #define CONFIG_SYS_FSL_DDR2 79 #undef CONFIG_FSL_DDR_INTERACTIVE 80 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 81 #define CONFIG_DDR_SPD 82 83 #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 84 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 85 86 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 87 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 88 #define CONFIG_VERY_BIG_RAM 89 90 #define CONFIG_NUM_DDR_CONTROLLERS 1 91 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 92 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 93 94 /* I2C addresses of SPD EEPROMs */ 95 #define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */ 96 97 #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ 98 99 /* Hardcoded values, to use instead of SPD */ 100 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f 101 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 102 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 103 #define CONFIG_SYS_DDR_TIMING_1 0x3935D322 104 #define CONFIG_SYS_DDR_TIMING_2 0x14904CC8 105 #define CONFIG_SYS_DDR_MODE 0x00480432 106 #define CONFIG_SYS_DDR_INTERVAL 0x030C0100 107 #define CONFIG_SYS_DDR_CONFIG_2 0x04400000 108 #define CONFIG_SYS_DDR_CONFIG 0xC3008000 109 #define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000 110 #define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */ 111 112 /* 113 * Flash on the LocalBus 114 */ 115 #define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ 116 117 #define CONFIG_SYS_FLASH0 0xFE000000 118 #define CONFIG_SYS_FLASH1 0xFC000000 119 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } 120 121 #define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ 122 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ 123 124 #define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */ 125 #define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */ 126 #define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */ 127 #define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */ 128 129 #define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ 130 #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/ 131 132 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 133 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ 134 #undef CONFIG_SYS_FLASH_CHECKSUM 135 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 136 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 137 138 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 139 140 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 141 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 142 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 143 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ 144 145 #define CONFIG_SYS_INIT_RAM_LOCK 1 146 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 147 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/ 148 149 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 150 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 151 152 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */ 153 #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */ 154 155 /* FPGA and NAND */ 156 #define CONFIG_SYS_FPGA_BASE 0xc0000000 157 #define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */ 158 #define CONFIG_SYS_HMI_BASE 0xc0010000 159 #define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ 160 #define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */ 161 162 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70) 163 #define CONFIG_SYS_MAX_NAND_DEVICE 1 164 #define CONFIG_CMD_NAND 165 166 /* LIME GDC */ 167 #define CONFIG_SYS_LIME_BASE 0xc8000000 168 #define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */ 169 #define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */ 170 #define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */ 171 172 #define CONFIG_VIDEO 173 #define CONFIG_VIDEO_MB862xx 174 #define CONFIG_VIDEO_MB862xx_ACCEL 175 #define CONFIG_CFB_CONSOLE 176 #define CONFIG_VIDEO_LOGO 177 #define CONFIG_VIDEO_BMP_LOGO 178 #define CONFIG_CONSOLE_EXTRA_INFO 179 #define VIDEO_FB_16BPP_PIXEL_SWAP 180 #define VIDEO_FB_16BPP_WORD_SWAP 181 #define CONFIG_VGA_AS_SINGLE_DEVICE 182 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 183 #define CONFIG_VIDEO_SW_CURSOR 184 #define CONFIG_SPLASH_SCREEN 185 #define CONFIG_VIDEO_BMP_GZIP 186 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ 187 188 /* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */ 189 #define CONFIG_SYS_MB862xx_CCF 0x10000 190 /* SDRAM parameter */ 191 #define CONFIG_SYS_MB862xx_MMR 0x4157BA63 192 193 /* Serial Port */ 194 195 #define CONFIG_CONS_INDEX 1 196 #define CONFIG_SYS_NS16550_SERIAL 197 #define CONFIG_SYS_NS16550_REG_SIZE 1 198 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 199 200 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 201 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 202 203 #define CONFIG_BAUDRATE 115200 204 205 #define CONFIG_SYS_BAUDRATE_TABLE \ 206 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 207 208 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 209 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 210 #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ 211 212 213 /* 214 * I2C 215 */ 216 #define CONFIG_SYS_I2C 217 #define CONFIG_SYS_I2C_FSL 218 #define CONFIG_SYS_FSL_I2C_SPEED 102124 219 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 220 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 221 #define CONFIG_SYS_FSL_I2C2_SPEED 102124 222 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 223 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 224 225 /* I2C RTC */ 226 #define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */ 227 #define CONFIG_SYS_I2C_RTC_ADDR 0x32 /* at address 0x32 */ 228 229 /* I2C W83782G HW-Monitoring IC */ 230 #define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */ 231 232 /* I2C temp sensor */ 233 /* Socrates uses Maxim's DS75, which is compatible with LM75 */ 234 #define CONFIG_DTT_LM75 1 235 #define CONFIG_DTT_SENSORS {4} /* Sensor addresses */ 236 #define CONFIG_SYS_DTT_MAX_TEMP 125 237 #define CONFIG_SYS_DTT_LOW_TEMP -55 238 #define CONFIG_SYS_DTT_HYSTERESIS 3 239 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 240 241 /* 242 * General PCI 243 * Memory space is mapped 1-1. 244 */ 245 #define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */ 246 247 /* PCI is clocked by the external source at 33 MHz */ 248 #define CONFIG_PCI_CLK_FREQ 33000000 249 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 250 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 251 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 252 #define CONFIG_SYS_PCI1_IO_BASE 0xE2000000 253 #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE 254 #define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */ 255 256 #if defined(CONFIG_PCI) 257 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 258 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 259 #endif /* CONFIG_PCI */ 260 261 262 #define CONFIG_MII 1 /* MII PHY management */ 263 #define CONFIG_TSEC1 1 264 #define CONFIG_TSEC1_NAME "TSEC0" 265 #define CONFIG_TSEC3 1 266 #define CONFIG_TSEC3_NAME "TSEC1" 267 #undef CONFIG_MPC85XX_FEC 268 269 #define TSEC1_PHY_ADDR 0 270 #define TSEC3_PHY_ADDR 1 271 272 #define TSEC1_PHYIDX 0 273 #define TSEC3_PHYIDX 0 274 #define TSEC1_FLAGS TSEC_GIGABIT 275 #define TSEC3_FLAGS TSEC_GIGABIT 276 277 /* Options are: TSEC[0,1] */ 278 #define CONFIG_ETHPRIME "TSEC0" 279 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 280 281 #define CONFIG_HAS_ETH0 282 #define CONFIG_HAS_ETH1 283 284 /* 285 * Environment 286 */ 287 #define CONFIG_ENV_IS_IN_FLASH 1 288 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 289 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 290 #define CONFIG_ENV_SIZE 0x4000 291 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) 292 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 293 294 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 295 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 296 297 #define CONFIG_TIMESTAMP /* Print image info with ts */ 298 299 300 /* 301 * BOOTP options 302 */ 303 #define CONFIG_BOOTP_BOOTFILESIZE 304 #define CONFIG_BOOTP_BOOTPATH 305 #define CONFIG_BOOTP_GATEWAY 306 #define CONFIG_BOOTP_HOSTNAME 307 308 309 /* 310 * Command line configuration. 311 */ 312 #define CONFIG_CMD_BMP 313 #define CONFIG_CMD_DATE 314 #define CONFIG_CMD_DHCP 315 #define CONFIG_CMD_DTT 316 #undef CONFIG_CMD_EEPROM 317 #define CONFIG_CMD_EXT2 /* EXT2 Support */ 318 #define CONFIG_CMD_I2C 319 #define CONFIG_CMD_SDRAM 320 #define CONFIG_CMD_MII 321 #define CONFIG_CMD_PING 322 #define CONFIG_CMD_SNTP 323 #define CONFIG_CMD_USB 324 #define CONFIG_CMD_REGINFO 325 326 #if defined(CONFIG_PCI) 327 #define CONFIG_CMD_PCI 328 #endif 329 330 #undef CONFIG_WATCHDOG /* watchdog disabled */ 331 332 /* 333 * Miscellaneous configurable options 334 */ 335 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 336 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 337 338 #if defined(CONFIG_CMD_KGDB) 339 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 340 #else 341 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 342 #endif 343 344 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size */ 345 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 346 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 347 348 /* 349 * For booting Linux, the board info and command line data 350 * have to be in the first 8 MB of memory, since this is 351 * the maximum mapped by the Linux kernel during initialization. 352 */ 353 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 354 355 #if defined(CONFIG_CMD_KGDB) 356 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ 357 #endif 358 359 360 #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ 361 362 #define CONFIG_BOOTDELAY 1 /* -1 disables auto-boot */ 363 364 #define CONFIG_PREBOOT "echo;" \ 365 "echo Welcome on the ABB Socrates Board;" \ 366 "echo" 367 368 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 369 370 #define CONFIG_EXTRA_ENV_SETTINGS \ 371 "netdev=eth0\0" \ 372 "consdev=ttyS0\0" \ 373 "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \ 374 "bootfile=/home/tftp/syscon3/uImage\0" \ 375 "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \ 376 "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \ 377 "uboot_addr=FFFA0000\0" \ 378 "kernel_addr=FE000000\0" \ 379 "fdt_addr=FE1E0000\0" \ 380 "ramdisk_addr=FE200000\0" \ 381 "fdt_addr_r=B00000\0" \ 382 "kernel_addr_r=200000\0" \ 383 "ramdisk_addr_r=400000\0" \ 384 "rootpath=/opt/eldk/ppc_85xxDP\0" \ 385 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 386 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 387 "nfsroot=$serverip:$rootpath\0" \ 388 "addcons=setenv bootargs $bootargs " \ 389 "console=$consdev,$baudrate\0" \ 390 "addip=setenv bootargs $bootargs " \ 391 "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ 392 ":$hostname:$netdev:off panic=1\0" \ 393 "boot_nor=run ramargs addcons;" \ 394 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 395 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 396 "tftp ${fdt_addr_r} ${fdt_file}; " \ 397 "run nfsargs addip addcons;" \ 398 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 399 "update_uboot=tftp 100000 ${uboot_file};" \ 400 "protect off fffa0000 ffffffff;" \ 401 "era fffa0000 ffffffff;" \ 402 "cp.b 100000 fffa0000 ${filesize};" \ 403 "setenv filesize;saveenv\0" \ 404 "update_kernel=tftp 100000 ${bootfile};" \ 405 "era fe000000 fe1dffff;" \ 406 "cp.b 100000 fe000000 ${filesize};" \ 407 "setenv filesize;saveenv\0" \ 408 "update_fdt=tftp 100000 ${fdt_file};" \ 409 "era fe1e0000 fe1fffff;" \ 410 "cp.b 100000 fe1e0000 ${filesize};" \ 411 "setenv filesize;saveenv\0" \ 412 "update_initrd=tftp 100000 ${initrd_file};" \ 413 "era fe200000 fe9fffff;" \ 414 "cp.b 100000 fe200000 ${filesize};" \ 415 "setenv filesize;saveenv\0" \ 416 "clean_data=era fea00000 fff5ffff\0" \ 417 "usbargs=setenv bootargs root=/dev/sda1 rw\0" \ 418 "load_usb=usb start;" \ 419 "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \ 420 "boot_usb=run load_usb usbargs addcons;" \ 421 "bootm ${kernel_addr_r} - ${fdt_addr};" \ 422 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 423 "" 424 #define CONFIG_BOOTCOMMAND "run boot_nor" 425 426 /* pass open firmware flat tree */ 427 428 /* USB support */ 429 #define CONFIG_USB_OHCI_NEW 1 430 #define CONFIG_PCI_OHCI 1 431 #define CONFIG_PCI_OHCI_DEVNO 3 /* Number in PCI list */ 432 #define CONFIG_PCI_EHCI_DEVNO (CONFIG_PCI_OHCI_DEVNO / 2) 433 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 434 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 435 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 436 #define CONFIG_DOS_PARTITION 1 437 #define CONFIG_USB_STORAGE 1 438 439 #endif /* __CONFIG_H */ 440