1 /* 2 * (C) Copyright 2008 3 * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. 4 * 5 * Wolfgang Denk <wd@denx.de> 6 * Copyright 2004 Freescale Semiconductor. 7 * (C) Copyright 2002,2003 Motorola,Inc. 8 * Xianghua Xiao <X.Xiao@motorola.com> 9 * 10 * See file CREDITS for list of people who contributed to this 11 * project. 12 * 13 * This program is free software; you can redistribute it and/or 14 * modify it under the terms of the GNU General Public License as 15 * published by the Free Software Foundation; either version 2 of 16 * the License, or (at your option) any later version. 17 * 18 * This program is distributed in the hope that it will be useful, 19 * but WITHOUT ANY WARRANTY; without even the implied warranty of 20 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 21 * GNU General Public License for more details. 22 * 23 * You should have received a copy of the GNU General Public License 24 * along with this program; if not, write to the Free Software 25 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 26 * MA 02111-1307 USA 27 */ 28 29 /* 30 * Socrates 31 */ 32 33 #ifndef __CONFIG_H 34 #define __CONFIG_H 35 36 /* new uImage format support */ 37 #define CONFIG_FIT 1 38 #define CONFIG_OF_LIBFDT 1 39 #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ 40 41 /* High Level Configuration Options */ 42 #define CONFIG_BOOKE 1 /* BOOKE */ 43 #define CONFIG_E500 1 /* BOOKE e500 family */ 44 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ 45 #define CONFIG_MPC8544 1 46 #define CONFIG_SOCRATES 1 47 48 #define CONFIG_PCI 49 50 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 51 52 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ 53 #define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ 54 55 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 56 57 /* 58 * Only possible on E500 Version 2 or newer cores. 59 */ 60 #define CONFIG_ENABLE_36BIT_PHYS 1 61 62 /* 63 * sysclk for MPC85xx 64 * 65 * Two valid values are: 66 * 33000000 67 * 66000000 68 * 69 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz 70 * is likely the desired value here, so that is now the default. 71 * The board, however, can run at 66MHz. In any event, this value 72 * must match the settings of some switches. Details can be found 73 * in the README.mpc85xxads. 74 */ 75 76 #ifndef CONFIG_SYS_CLK_FREQ 77 #define CONFIG_SYS_CLK_FREQ 66666666 78 #endif 79 80 /* 81 * These can be toggled for performance analysis, otherwise use default. 82 */ 83 #define CONFIG_L2_CACHE /* toggle L2 cache */ 84 #define CONFIG_BTB /* toggle branch predition */ 85 86 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ 87 88 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 89 #define CONFIG_SYS_MEMTEST_START 0x00400000 90 #define CONFIG_SYS_MEMTEST_END 0x00C00000 91 92 /* 93 * Base addresses -- Note these are effective addresses where the 94 * actual resources get mapped (not physical addresses) 95 */ 96 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ 97 #define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ 98 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ 99 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 100 101 /* DDR Setup */ 102 #define CONFIG_FSL_DDR2 103 #undef CONFIG_FSL_DDR_INTERACTIVE 104 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 105 #define CONFIG_DDR_SPD 106 107 #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 108 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 109 110 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 111 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 112 #define CONFIG_VERY_BIG_RAM 113 114 #define CONFIG_NUM_DDR_CONTROLLERS 1 115 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 116 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 117 118 /* I2C addresses of SPD EEPROMs */ 119 #define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */ 120 121 #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ 122 123 /* Hardcoded values, to use instead of SPD */ 124 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f 125 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 126 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 127 #define CONFIG_SYS_DDR_TIMING_1 0x3935D322 128 #define CONFIG_SYS_DDR_TIMING_2 0x14904CC8 129 #define CONFIG_SYS_DDR_MODE 0x00480432 130 #define CONFIG_SYS_DDR_INTERVAL 0x030C0100 131 #define CONFIG_SYS_DDR_CONFIG_2 0x04400000 132 #define CONFIG_SYS_DDR_CONFIG 0xC3008000 133 #define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000 134 #define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */ 135 136 /* 137 * Flash on the LocalBus 138 */ 139 #define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ 140 141 #define CONFIG_SYS_FLASH0 0xFE000000 142 #define CONFIG_SYS_FLASH1 0xFC000000 143 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } 144 145 #define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ 146 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ 147 148 #define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */ 149 #define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */ 150 #define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */ 151 #define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */ 152 153 #define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ 154 #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/ 155 156 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 157 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ 158 #undef CONFIG_SYS_FLASH_CHECKSUM 159 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 160 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 161 162 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ 163 164 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 165 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 166 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 167 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ 168 169 #define CONFIG_SYS_INIT_RAM_LOCK 1 170 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 171 #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End used area in RAM */ 172 173 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data*/ 174 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 175 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 176 177 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon */ 178 #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */ 179 180 /* FPGA and NAND */ 181 #define CONFIG_SYS_FPGA_BASE 0xc0000000 182 #define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */ 183 #define CONFIG_SYS_HMI_BASE 0xc0010000 184 #define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ 185 #define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */ 186 187 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70) 188 #define CONFIG_SYS_MAX_NAND_DEVICE 1 189 #define CONFIG_CMD_NAND 190 191 /* LIME GDC */ 192 #define CONFIG_SYS_LIME_BASE 0xc8000000 193 #define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */ 194 #define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */ 195 #define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */ 196 197 #define CONFIG_VIDEO 198 #define CONFIG_VIDEO_MB862xx 199 #define CONFIG_CFB_CONSOLE 200 #define CONFIG_VIDEO_LOGO 201 #define CONFIG_VIDEO_BMP_LOGO 202 #define CONFIG_CONSOLE_EXTRA_INFO 203 #define VIDEO_FB_16BPP_PIXEL_SWAP 204 #define CONFIG_VGA_AS_SINGLE_DEVICE 205 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 206 #define CONFIG_VIDEO_SW_CURSOR 207 #define CONFIG_SPLASH_SCREEN 208 #define CONFIG_VIDEO_BMP_GZIP 209 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ 210 211 /* Serial Port */ 212 213 #define CONFIG_CONS_INDEX 1 214 #undef CONFIG_SERIAL_SOFTWARE_FIFO 215 #define CONFIG_SYS_NS16550 216 #define CONFIG_SYS_NS16550_SERIAL 217 #define CONFIG_SYS_NS16550_REG_SIZE 1 218 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 219 220 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 221 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 222 223 #define CONFIG_BAUDRATE 115200 224 225 #define CONFIG_SYS_BAUDRATE_TABLE \ 226 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 227 228 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 229 #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ 230 #ifdef CONFIG_SYS_HUSH_PARSER 231 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 232 #endif 233 234 235 /* 236 * I2C 237 */ 238 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 239 #define CONFIG_HARD_I2C /* I2C with hardware support */ 240 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 241 #define CONFIG_SYS_I2C_SPEED 102124 /* I2C speed and slave address */ 242 #define CONFIG_SYS_I2C_SLAVE 0x7F 243 #define CONFIG_SYS_I2C_OFFSET 0x3000 244 245 #define CONFIG_I2C_MULTI_BUS 246 #define CONFIG_SYS_I2C2_OFFSET 0x3100 247 248 /* I2C RTC */ 249 #define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */ 250 #define CONFIG_SYS_I2C_RTC_ADDR 0x32 /* at address 0x32 */ 251 252 /* I2C W83782G HW-Monitoring IC */ 253 #define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */ 254 255 /* I2C temp sensor */ 256 /* Socrates uses Maxim's DS75, which is compatible with LM75 */ 257 #define CONFIG_DTT_LM75 1 258 #define CONFIG_DTT_SENSORS {4} /* Sensor addresses */ 259 #define CONFIG_SYS_DTT_MAX_TEMP 125 260 #define CONFIG_SYS_DTT_LOW_TEMP -55 261 #define CONFIG_SYS_DTT_HYSTERESIS 3 262 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 263 264 /* 265 * General PCI 266 * Memory space is mapped 1-1. 267 */ 268 #define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */ 269 270 /* PCI is clocked by the external source at 33 MHz */ 271 #define CONFIG_PCI_CLK_FREQ 33000000 272 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 273 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 274 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 275 #define CONFIG_SYS_PCI1_IO_BASE 0xE2000000 276 #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE 277 #define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */ 278 279 #if defined(CONFIG_PCI) 280 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 281 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 282 #endif /* CONFIG_PCI */ 283 284 285 #define CONFIG_NET_MULTI 1 286 #define CONFIG_MII 1 /* MII PHY management */ 287 #define CONFIG_TSEC1 1 288 #define CONFIG_TSEC1_NAME "TSEC0" 289 #define CONFIG_TSEC3 1 290 #define CONFIG_TSEC3_NAME "TSEC1" 291 #undef CONFIG_MPC85XX_FEC 292 293 #define TSEC1_PHY_ADDR 0 294 #define TSEC3_PHY_ADDR 1 295 296 #define TSEC1_PHYIDX 0 297 #define TSEC3_PHYIDX 0 298 #define TSEC1_FLAGS TSEC_GIGABIT 299 #define TSEC3_FLAGS TSEC_GIGABIT 300 301 /* Options are: TSEC[0,1] */ 302 #define CONFIG_ETHPRIME "TSEC0" 303 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 304 305 #define CONFIG_HAS_ETH0 306 #define CONFIG_HAS_ETH1 307 308 /* 309 * Environment 310 */ 311 #define CONFIG_ENV_IS_IN_FLASH 1 312 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 313 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 314 #define CONFIG_ENV_SIZE 0x4000 315 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) 316 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 317 318 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 319 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 320 321 #define CONFIG_TIMESTAMP /* Print image info with ts */ 322 323 324 /* 325 * BOOTP options 326 */ 327 #define CONFIG_BOOTP_BOOTFILESIZE 328 #define CONFIG_BOOTP_BOOTPATH 329 #define CONFIG_BOOTP_GATEWAY 330 #define CONFIG_BOOTP_HOSTNAME 331 332 333 /* 334 * Command line configuration. 335 */ 336 #include <config_cmd_default.h> 337 338 #define CONFIG_CMD_DATE 339 #define CONFIG_CMD_DHCP 340 #define CONFIG_CMD_DTT 341 #undef CONFIG_CMD_EEPROM 342 #define CONFIG_CMD_I2C 343 #define CONFIG_CMD_SDRAM 344 #define CONFIG_CMD_MII 345 #define CONFIG_CMD_NFS 346 #define CONFIG_CMD_PING 347 #define CONFIG_CMD_SNTP 348 #define CONFIG_CMD_USB 349 #define CONFIG_CMD_EXT2 /* EXT2 Support */ 350 #define CONFIG_CMD_BMP 351 352 #if defined(CONFIG_PCI) 353 #define CONFIG_CMD_PCI 354 #endif 355 356 #undef CONFIG_WATCHDOG /* watchdog disabled */ 357 358 /* 359 * Miscellaneous configurable options 360 */ 361 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 362 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 363 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 364 365 #if defined(CONFIG_CMD_KGDB) 366 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 367 #else 368 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 369 #endif 370 371 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size */ 372 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 373 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 374 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 375 376 /* 377 * For booting Linux, the board info and command line data 378 * have to be in the first 8 MB of memory, since this is 379 * the maximum mapped by the Linux kernel during initialization. 380 */ 381 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 382 383 /* 384 * Internal Definitions 385 * 386 * Boot Flags 387 */ 388 #define BOOTFLAG_COLD 0x01 /* Power-On: Boot from FLASH */ 389 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 390 391 #if defined(CONFIG_CMD_KGDB) 392 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ 393 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 394 #endif 395 396 397 #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ 398 399 #define CONFIG_BOOTDELAY 1 /* -1 disables auto-boot */ 400 401 #define CONFIG_PREBOOT "echo;" \ 402 "echo Welcome on the ABB Socrates Board;" \ 403 "echo" 404 405 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 406 407 #define CONFIG_EXTRA_ENV_SETTINGS \ 408 "netdev=eth0\0" \ 409 "consdev=ttyS0\0" \ 410 "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \ 411 "bootfile=/home/tftp/syscon3/uImage\0" \ 412 "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \ 413 "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \ 414 "uboot_addr=FFFA0000\0" \ 415 "kernel_addr=FE000000\0" \ 416 "fdt_addr=FE1E0000\0" \ 417 "ramdisk_addr=FE200000\0" \ 418 "fdt_addr_r=B00000\0" \ 419 "kernel_addr_r=200000\0" \ 420 "ramdisk_addr_r=400000\0" \ 421 "rootpath=/opt/eldk/ppc_85xxDP\0" \ 422 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 423 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 424 "nfsroot=$serverip:$rootpath\0" \ 425 "addcons=setenv bootargs $bootargs " \ 426 "console=$consdev,$baudrate\0" \ 427 "addip=setenv bootargs $bootargs " \ 428 "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ 429 ":$hostname:$netdev:off panic=1\0" \ 430 "boot_nor=run ramargs addcons;" \ 431 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 432 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 433 "tftp ${fdt_addr_r} ${fdt_file}; " \ 434 "run nfsargs addip addcons;" \ 435 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 436 "update_uboot=tftp 100000 ${uboot_file};" \ 437 "protect off fffa0000 ffffffff;" \ 438 "era fffa0000 ffffffff;" \ 439 "cp.b 100000 fffa0000 ${filesize};" \ 440 "setenv filesize;saveenv\0" \ 441 "update_kernel=tftp 100000 ${bootfile};" \ 442 "era fe000000 fe1dffff;" \ 443 "cp.b 100000 fe000000 ${filesize};" \ 444 "setenv filesize;saveenv\0" \ 445 "update_fdt=tftp 100000 ${fdt_file};" \ 446 "era fe1e0000 fe1fffff;" \ 447 "cp.b 100000 fe1e0000 ${filesize};" \ 448 "setenv filesize;saveenv\0" \ 449 "update_initrd=tftp 100000 ${initrd_file};" \ 450 "era fe200000 fe9fffff;" \ 451 "cp.b 100000 fe200000 ${filesize};" \ 452 "setenv filesize;saveenv\0" \ 453 "clean_data=era fea00000 fff5ffff\0" \ 454 "usbargs=setenv bootargs root=/dev/sda1 rw\0" \ 455 "load_usb=usb start;" \ 456 "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \ 457 "boot_usb=run load_usb usbargs addcons;" \ 458 "bootm ${kernel_addr_r} - ${fdt_addr};" \ 459 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 460 "" 461 #define CONFIG_BOOTCOMMAND "run boot_nor" 462 463 /* pass open firmware flat tree */ 464 #define CONFIG_OF_LIBFDT 1 465 #define CONFIG_OF_BOARD_SETUP 1 466 467 /* USB support */ 468 #define CONFIG_USB_OHCI_NEW 1 469 #define CONFIG_PCI_OHCI 1 470 #define CONFIG_PCI_OHCI_DEVNO 3 /* Number in PCI list */ 471 #define CONFIG_PCI_EHCI_DEVNO (CONFIG_PCI_OHCI_DEVNO / 2) 472 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 473 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 474 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 475 #define CONFIG_DOS_PARTITION 1 476 #define CONFIG_USB_STORAGE 1 477 478 #endif /* __CONFIG_H */ 479