1 /* 2 * (C) Copyright 2008 3 * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. 4 * 5 * Wolfgang Denk <wd@denx.de> 6 * Copyright 2004 Freescale Semiconductor. 7 * (C) Copyright 2002,2003 Motorola,Inc. 8 * Xianghua Xiao <X.Xiao@motorola.com> 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 /* 14 * Socrates 15 */ 16 17 #ifndef __CONFIG_H 18 #define __CONFIG_H 19 20 /* new uImage format support */ 21 #define CONFIG_FIT 1 22 #define CONFIG_OF_LIBFDT 1 23 #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ 24 25 /* High Level Configuration Options */ 26 #define CONFIG_BOOKE 1 /* BOOKE */ 27 #define CONFIG_E500 1 /* BOOKE e500 family */ 28 #define CONFIG_MPC8544 1 29 #define CONFIG_SOCRATES 1 30 #define CONFIG_DISPLAY_BOARDINFO 31 32 #define CONFIG_SYS_TEXT_BASE 0xfff80000 33 34 #define CONFIG_PCI 35 #define CONFIG_PCI_INDIRECT_BRIDGE 36 37 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 38 39 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ 40 #define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ 41 42 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 43 44 /* 45 * Only possible on E500 Version 2 or newer cores. 46 */ 47 #define CONFIG_ENABLE_36BIT_PHYS 1 48 49 /* 50 * sysclk for MPC85xx 51 * 52 * Two valid values are: 53 * 33000000 54 * 66000000 55 * 56 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz 57 * is likely the desired value here, so that is now the default. 58 * The board, however, can run at 66MHz. In any event, this value 59 * must match the settings of some switches. Details can be found 60 * in the README.mpc85xxads. 61 */ 62 63 #ifndef CONFIG_SYS_CLK_FREQ 64 #define CONFIG_SYS_CLK_FREQ 66666666 65 #endif 66 67 /* 68 * These can be toggled for performance analysis, otherwise use default. 69 */ 70 #define CONFIG_L2_CACHE /* toggle L2 cache */ 71 #define CONFIG_BTB /* toggle branch predition */ 72 73 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ 74 75 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 76 #define CONFIG_SYS_MEMTEST_START 0x00400000 77 #define CONFIG_SYS_MEMTEST_END 0x00C00000 78 79 #define CONFIG_SYS_CCSRBAR 0xE0000000 80 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 81 82 /* DDR Setup */ 83 #define CONFIG_SYS_FSL_DDR2 84 #undef CONFIG_FSL_DDR_INTERACTIVE 85 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 86 #define CONFIG_DDR_SPD 87 88 #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 89 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 90 91 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 92 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 93 #define CONFIG_VERY_BIG_RAM 94 95 #define CONFIG_NUM_DDR_CONTROLLERS 1 96 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 97 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 98 99 /* I2C addresses of SPD EEPROMs */ 100 #define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */ 101 102 #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ 103 104 /* Hardcoded values, to use instead of SPD */ 105 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f 106 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 107 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 108 #define CONFIG_SYS_DDR_TIMING_1 0x3935D322 109 #define CONFIG_SYS_DDR_TIMING_2 0x14904CC8 110 #define CONFIG_SYS_DDR_MODE 0x00480432 111 #define CONFIG_SYS_DDR_INTERVAL 0x030C0100 112 #define CONFIG_SYS_DDR_CONFIG_2 0x04400000 113 #define CONFIG_SYS_DDR_CONFIG 0xC3008000 114 #define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000 115 #define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */ 116 117 /* 118 * Flash on the LocalBus 119 */ 120 #define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ 121 122 #define CONFIG_SYS_FLASH0 0xFE000000 123 #define CONFIG_SYS_FLASH1 0xFC000000 124 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } 125 126 #define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ 127 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ 128 129 #define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */ 130 #define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */ 131 #define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */ 132 #define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */ 133 134 #define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ 135 #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/ 136 137 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 138 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ 139 #undef CONFIG_SYS_FLASH_CHECKSUM 140 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 141 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 142 143 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 144 145 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 146 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 147 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 148 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ 149 150 #define CONFIG_SYS_INIT_RAM_LOCK 1 151 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 152 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/ 153 154 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 155 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 156 157 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */ 158 #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */ 159 160 /* FPGA and NAND */ 161 #define CONFIG_SYS_FPGA_BASE 0xc0000000 162 #define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */ 163 #define CONFIG_SYS_HMI_BASE 0xc0010000 164 #define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ 165 #define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */ 166 167 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70) 168 #define CONFIG_SYS_MAX_NAND_DEVICE 1 169 #define CONFIG_CMD_NAND 170 171 /* LIME GDC */ 172 #define CONFIG_SYS_LIME_BASE 0xc8000000 173 #define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */ 174 #define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */ 175 #define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */ 176 177 #define CONFIG_VIDEO 178 #define CONFIG_VIDEO_MB862xx 179 #define CONFIG_VIDEO_MB862xx_ACCEL 180 #define CONFIG_CFB_CONSOLE 181 #define CONFIG_VIDEO_LOGO 182 #define CONFIG_VIDEO_BMP_LOGO 183 #define CONFIG_CONSOLE_EXTRA_INFO 184 #define VIDEO_FB_16BPP_PIXEL_SWAP 185 #define VIDEO_FB_16BPP_WORD_SWAP 186 #define CONFIG_VGA_AS_SINGLE_DEVICE 187 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 188 #define CONFIG_VIDEO_SW_CURSOR 189 #define CONFIG_SPLASH_SCREEN 190 #define CONFIG_VIDEO_BMP_GZIP 191 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ 192 193 /* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */ 194 #define CONFIG_SYS_MB862xx_CCF 0x10000 195 /* SDRAM parameter */ 196 #define CONFIG_SYS_MB862xx_MMR 0x4157BA63 197 198 /* Serial Port */ 199 200 #define CONFIG_CONS_INDEX 1 201 #define CONFIG_SYS_NS16550_SERIAL 202 #define CONFIG_SYS_NS16550_REG_SIZE 1 203 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 204 205 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 206 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 207 208 #define CONFIG_BAUDRATE 115200 209 210 #define CONFIG_SYS_BAUDRATE_TABLE \ 211 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 212 213 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 214 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 215 #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ 216 217 218 /* 219 * I2C 220 */ 221 #define CONFIG_SYS_I2C 222 #define CONFIG_SYS_I2C_FSL 223 #define CONFIG_SYS_FSL_I2C_SPEED 102124 224 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 225 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 226 #define CONFIG_SYS_FSL_I2C2_SPEED 102124 227 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 228 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 229 230 /* I2C RTC */ 231 #define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */ 232 #define CONFIG_SYS_I2C_RTC_ADDR 0x32 /* at address 0x32 */ 233 234 /* I2C W83782G HW-Monitoring IC */ 235 #define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */ 236 237 /* I2C temp sensor */ 238 /* Socrates uses Maxim's DS75, which is compatible with LM75 */ 239 #define CONFIG_DTT_LM75 1 240 #define CONFIG_DTT_SENSORS {4} /* Sensor addresses */ 241 #define CONFIG_SYS_DTT_MAX_TEMP 125 242 #define CONFIG_SYS_DTT_LOW_TEMP -55 243 #define CONFIG_SYS_DTT_HYSTERESIS 3 244 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 245 246 /* 247 * General PCI 248 * Memory space is mapped 1-1. 249 */ 250 #define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */ 251 252 /* PCI is clocked by the external source at 33 MHz */ 253 #define CONFIG_PCI_CLK_FREQ 33000000 254 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 255 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 256 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 257 #define CONFIG_SYS_PCI1_IO_BASE 0xE2000000 258 #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE 259 #define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */ 260 261 #if defined(CONFIG_PCI) 262 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 263 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 264 #endif /* CONFIG_PCI */ 265 266 267 #define CONFIG_MII 1 /* MII PHY management */ 268 #define CONFIG_TSEC1 1 269 #define CONFIG_TSEC1_NAME "TSEC0" 270 #define CONFIG_TSEC3 1 271 #define CONFIG_TSEC3_NAME "TSEC1" 272 #undef CONFIG_MPC85XX_FEC 273 274 #define TSEC1_PHY_ADDR 0 275 #define TSEC3_PHY_ADDR 1 276 277 #define TSEC1_PHYIDX 0 278 #define TSEC3_PHYIDX 0 279 #define TSEC1_FLAGS TSEC_GIGABIT 280 #define TSEC3_FLAGS TSEC_GIGABIT 281 282 /* Options are: TSEC[0,1] */ 283 #define CONFIG_ETHPRIME "TSEC0" 284 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 285 286 #define CONFIG_HAS_ETH0 287 #define CONFIG_HAS_ETH1 288 289 /* 290 * Environment 291 */ 292 #define CONFIG_ENV_IS_IN_FLASH 1 293 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 294 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 295 #define CONFIG_ENV_SIZE 0x4000 296 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) 297 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 298 299 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 300 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 301 302 #define CONFIG_TIMESTAMP /* Print image info with ts */ 303 304 305 /* 306 * BOOTP options 307 */ 308 #define CONFIG_BOOTP_BOOTFILESIZE 309 #define CONFIG_BOOTP_BOOTPATH 310 #define CONFIG_BOOTP_GATEWAY 311 #define CONFIG_BOOTP_HOSTNAME 312 313 314 /* 315 * Command line configuration. 316 */ 317 #define CONFIG_CMD_BMP 318 #define CONFIG_CMD_DATE 319 #define CONFIG_CMD_DHCP 320 #define CONFIG_CMD_DTT 321 #undef CONFIG_CMD_EEPROM 322 #define CONFIG_CMD_EXT2 /* EXT2 Support */ 323 #define CONFIG_CMD_I2C 324 #define CONFIG_CMD_SDRAM 325 #define CONFIG_CMD_MII 326 #define CONFIG_CMD_PING 327 #define CONFIG_CMD_SNTP 328 #define CONFIG_CMD_USB 329 #define CONFIG_CMD_REGINFO 330 331 #if defined(CONFIG_PCI) 332 #define CONFIG_CMD_PCI 333 #endif 334 335 #undef CONFIG_WATCHDOG /* watchdog disabled */ 336 337 /* 338 * Miscellaneous configurable options 339 */ 340 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 341 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 342 343 #if defined(CONFIG_CMD_KGDB) 344 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 345 #else 346 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 347 #endif 348 349 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size */ 350 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 351 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 352 353 /* 354 * For booting Linux, the board info and command line data 355 * have to be in the first 8 MB of memory, since this is 356 * the maximum mapped by the Linux kernel during initialization. 357 */ 358 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 359 360 #if defined(CONFIG_CMD_KGDB) 361 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ 362 #endif 363 364 365 #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ 366 367 #define CONFIG_BOOTDELAY 1 /* -1 disables auto-boot */ 368 369 #define CONFIG_PREBOOT "echo;" \ 370 "echo Welcome on the ABB Socrates Board;" \ 371 "echo" 372 373 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 374 375 #define CONFIG_EXTRA_ENV_SETTINGS \ 376 "netdev=eth0\0" \ 377 "consdev=ttyS0\0" \ 378 "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \ 379 "bootfile=/home/tftp/syscon3/uImage\0" \ 380 "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \ 381 "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \ 382 "uboot_addr=FFFA0000\0" \ 383 "kernel_addr=FE000000\0" \ 384 "fdt_addr=FE1E0000\0" \ 385 "ramdisk_addr=FE200000\0" \ 386 "fdt_addr_r=B00000\0" \ 387 "kernel_addr_r=200000\0" \ 388 "ramdisk_addr_r=400000\0" \ 389 "rootpath=/opt/eldk/ppc_85xxDP\0" \ 390 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 391 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 392 "nfsroot=$serverip:$rootpath\0" \ 393 "addcons=setenv bootargs $bootargs " \ 394 "console=$consdev,$baudrate\0" \ 395 "addip=setenv bootargs $bootargs " \ 396 "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ 397 ":$hostname:$netdev:off panic=1\0" \ 398 "boot_nor=run ramargs addcons;" \ 399 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 400 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 401 "tftp ${fdt_addr_r} ${fdt_file}; " \ 402 "run nfsargs addip addcons;" \ 403 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 404 "update_uboot=tftp 100000 ${uboot_file};" \ 405 "protect off fffa0000 ffffffff;" \ 406 "era fffa0000 ffffffff;" \ 407 "cp.b 100000 fffa0000 ${filesize};" \ 408 "setenv filesize;saveenv\0" \ 409 "update_kernel=tftp 100000 ${bootfile};" \ 410 "era fe000000 fe1dffff;" \ 411 "cp.b 100000 fe000000 ${filesize};" \ 412 "setenv filesize;saveenv\0" \ 413 "update_fdt=tftp 100000 ${fdt_file};" \ 414 "era fe1e0000 fe1fffff;" \ 415 "cp.b 100000 fe1e0000 ${filesize};" \ 416 "setenv filesize;saveenv\0" \ 417 "update_initrd=tftp 100000 ${initrd_file};" \ 418 "era fe200000 fe9fffff;" \ 419 "cp.b 100000 fe200000 ${filesize};" \ 420 "setenv filesize;saveenv\0" \ 421 "clean_data=era fea00000 fff5ffff\0" \ 422 "usbargs=setenv bootargs root=/dev/sda1 rw\0" \ 423 "load_usb=usb start;" \ 424 "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \ 425 "boot_usb=run load_usb usbargs addcons;" \ 426 "bootm ${kernel_addr_r} - ${fdt_addr};" \ 427 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 428 "" 429 #define CONFIG_BOOTCOMMAND "run boot_nor" 430 431 /* pass open firmware flat tree */ 432 #define CONFIG_OF_LIBFDT 1 433 #define CONFIG_OF_BOARD_SETUP 1 434 435 /* USB support */ 436 #define CONFIG_USB_OHCI_NEW 1 437 #define CONFIG_PCI_OHCI 1 438 #define CONFIG_PCI_OHCI_DEVNO 3 /* Number in PCI list */ 439 #define CONFIG_PCI_EHCI_DEVNO (CONFIG_PCI_OHCI_DEVNO / 2) 440 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 441 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 442 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 443 #define CONFIG_DOS_PARTITION 1 444 #define CONFIG_USB_STORAGE 1 445 446 #endif /* __CONFIG_H */ 447