1 /* 2 * Copyright (C) 2015 Marek Vasut <marex@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 #ifndef __CONFIG_SAMTEC_VINING_FPGA_H__ 7 #define __CONFIG_SAMTEC_VINING_FPGA_H__ 8 9 #include <asm/arch/base_addr_ac5.h> 10 11 #define CONFIG_HW_WATCHDOG 12 13 /* Memory configurations */ 14 #define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on VINING_FPGA */ 15 16 /* Booting Linux */ 17 #define CONFIG_BOOTFILE "openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb" 18 #define CONFIG_BOOTARGS "console=ttyS0," __stringify(CONFIG_BAUDRATE) 19 #define CONFIG_BOOTCOMMAND "run selboot" 20 #define CONFIG_LOADADDR 0x01000000 21 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 22 23 /* I2C EEPROM */ 24 #ifdef CONFIG_CMD_EEPROM 25 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 26 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 27 #define CONFIG_SYS_I2C_EEPROM_BUS 0 28 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 29 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 30 #endif 31 32 /* 33 * Status LEDs: 34 * 0 ... Top Green 35 * 1 ... Top Red 36 * 2 ... Bottom Green 37 * 3 ... Bottom Red 38 */ 39 40 /* Ethernet on SoC (EMAC) */ 41 #if defined(CONFIG_CMD_NET) 42 #define CONFIG_BOOTP_SEND_HOSTNAME 43 /* PHY */ 44 #endif 45 46 /* Extra Environment */ 47 #define CONFIG_HOSTNAME socfpga_vining_fpga 48 49 /* 50 * Active LOW GPIO buttons: 51 * A: GPIO 77 ... the button between USB B and ethernet 52 * B: GPIO 78 ... the button between USB A ports 53 * 54 * The logic: 55 * if button B is not pressed, boot normal Linux system immediatelly 56 * if button B is pressed, wait $bootdelay and boot recovery system 57 */ 58 #define CONFIG_PREBOOT \ 59 "setenv hostname vining-${unit_serial} ; " \ 60 "setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; " \ 61 "if gpio input 78 ; then " \ 62 "setenv bootdelay 10 ; " \ 63 "setenv boottype rcvr ; " \ 64 "else " \ 65 "setenv bootdelay 5 ; " \ 66 "setenv boottype norm ; " \ 67 "fi" 68 69 #define CONFIG_EXTRA_ENV_SETTINGS \ 70 "verify=n\0" \ 71 "consdev=ttyS0\0" \ 72 "baudrate=115200\0" \ 73 "bootscript=boot.scr\0" \ 74 "ubimtdnr=5\0" \ 75 "ubimtd=rootfs\0" \ 76 "ubipart=ubi0:rootfs\0" \ 77 "ubisfcs=1\0" /* Default is flash at CS#1 */ \ 78 "netdev=eth0\0" \ 79 "hostname=vining_fpga\0" \ 80 "kernel_addr_r=0x10000000\0" \ 81 "mtdparts_0=ff705000.spi.0:" \ 82 "1m(u-boot)," \ 83 "64k(env1)," \ 84 "64k(env2)," \ 85 "256k(samtec1)," \ 86 "256k(samtec2)," \ 87 "-(rcvrfs)\0" /* Recovery */ \ 88 "mtdparts_1=ff705000.spi.1:" \ 89 "32m(rootfs)," \ 90 "-(userfs)\0" \ 91 "update_filename=u-boot-with-spl-dtb.sfp\0" \ 92 "update_qspi_offset=0x0\0" \ 93 "update_qspi=" /* Update the QSPI firmware */ \ 94 "if sf probe ; then " \ 95 "if tftp ${update_filename} ; then " \ 96 "sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \ 97 "fi ; " \ 98 "fi\0" \ 99 "fpga_filename=output_file.rbf\0" \ 100 "load_fpga=" /* Load FPGA bitstream */ \ 101 "if tftp ${fpga_filename} ; then " \ 102 "fpga load 0 $loadaddr $filesize ; " \ 103 "bridge enable ; " \ 104 "fi\0" \ 105 "addcons=" \ 106 "setenv bootargs ${bootargs} " \ 107 "console=${consdev},${baudrate}\0" \ 108 "addip=" \ 109 "setenv bootargs ${bootargs} " \ 110 "ip=${ipaddr}:${serverip}:${gatewayip}:" \ 111 "${netmask}:${hostname}:${netdev}:off\0" \ 112 "addmisc=" \ 113 "setenv bootargs ${bootargs} ${miscargs}\0" \ 114 "addmtd=" \ 115 "setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; " \ 116 "setenv bootargs ${bootargs} mtdparts=${mtdparts}\0" \ 117 "addargs=run addcons addmtd addmisc\0" \ 118 "ubiload=" \ 119 "ubi part ${ubimtd} ; ubifsmount ${ubipart} ; " \ 120 "ubifsload ${kernel_addr_r} /boot/${bootfile}\0" \ 121 "netload=" \ 122 "tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \ 123 "miscargs=nohlt panic=1\0" \ 124 "ubiargs=" \ 125 "setenv bootargs ubi.mtd=${ubimtdnr} " \ 126 "root=${ubipart} rootfstype=ubifs\0" \ 127 "nfsargs=" \ 128 "setenv bootargs root=/dev/nfs rw " \ 129 "nfsroot=${serverip}:${rootpath},v3,tcp\0" \ 130 "ubi_sfsel=" \ 131 "if test \"${boottype}\" = \"rcvr\" ; then " \ 132 "setenv ubisfcs 0 ; " \ 133 "setenv ubimtd rcvrfs ; " \ 134 "setenv ubimtdnr 5 ; " \ 135 "setenv mtdparts mtdparts=${mtdparts_0} ; " \ 136 "setenv mtdids nor0=ff705000.spi.0 ; " \ 137 "setenv ubipart ubi0:rootfs ; " \ 138 "else " \ 139 "setenv ubisfcs 1 ; " \ 140 "setenv ubimtd rootfs ; " \ 141 "setenv ubimtdnr 6 ; " \ 142 "setenv mtdparts mtdparts=${mtdparts_1} ; " \ 143 "setenv mtdids nor0=ff705000.spi.1 ; " \ 144 "setenv ubipart ubi0:rootfs ; " \ 145 "fi ; " \ 146 "sf probe 0:${ubisfcs}\0" \ 147 "ubi_ubi=" \ 148 "run ubi_sfsel ubiload ubiargs addargs ; " \ 149 "bootm ${kernel_addr_r}\0" \ 150 "ubi_nfs=" \ 151 "run ubiload nfsargs addip addargs ; " \ 152 "bootm ${kernel_addr_r}\0" \ 153 "net_ubi=" \ 154 "run netload ubiargs addargs ; " \ 155 "bootm ${kernel_addr_r}\0" \ 156 "net_nfs=" \ 157 "run netload nfsargs addip addargs ; " \ 158 "bootm ${kernel_addr_r}\0" \ 159 "selboot=" /* Select from where to boot. */ \ 160 "if test \"${bootmode}\" = \"qspi\" ; then " \ 161 "led all off ; " \ 162 "if test \"${boottype}\" = \"rcvr\" ; then " \ 163 "echo \"Booting recovery system\" ; " \ 164 "led 3 on ; " /* Bottom RED */ \ 165 "fi ; " \ 166 "led 1 on ; " /* Top RED */ \ 167 "run ubi_ubi ; " \ 168 "else echo \"Unsupported boot mode: \"${bootmode} ; " \ 169 "fi\0" \ 170 171 #define MTDPARTS_DEFAULT \ 172 "mtdparts=ff705000.spi.0:" \ 173 "1m(u-boot)," \ 174 "64k(env1)," \ 175 "64k(env2)," \ 176 "256k(samtec1)," \ 177 "256k(samtec2)," \ 178 "-(rcvrfs);" /* Recovery */ \ 179 180 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 181 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 182 #define CONFIG_ENV_SECT_SIZE (64 * 1024) 183 #define CONFIG_ENV_OFFSET 0x100000 184 #define CONFIG_ENV_OFFSET_REDUND \ 185 (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) 186 187 #define CONFIG_MISC_INIT_R 188 189 /* Support changing the prompt string */ 190 #define CONFIG_CMDLINE_PS_SUPPORT 191 192 /* The rest of the configuration is shared */ 193 #include <configs/socfpga_common.h> 194 195 #endif /* __CONFIG_SAMTEC_VINING_FPGA_H__ */ 196