1 /* 2 * Copyright (C) 2012 Altera Corporation <www.altera.com> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 #ifndef __CONFIG_SOCFPGA_COMMON_H__ 7 #define __CONFIG_SOCFPGA_COMMON_H__ 8 9 /* Virtual target or real hardware */ 10 #undef CONFIG_SOCFPGA_VIRTUAL_TARGET 11 12 #define CONFIG_SYS_THUMB_BUILD 13 14 /* 15 * High level configuration 16 */ 17 #define CONFIG_DISPLAY_BOARDINFO_LATE 18 #define CONFIG_ARCH_MISC_INIT 19 #define CONFIG_ARCH_EARLY_INIT_R 20 #define CONFIG_SYS_NO_FLASH 21 #define CONFIG_CLOCKS 22 23 #define CONFIG_CRC32_VERIFY 24 25 #define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024) 26 27 #define CONFIG_TIMESTAMP /* Print image info with timestamp */ 28 29 /* add target to build it automatically upon "make" */ 30 #define CONFIG_BUILD_TARGET "u-boot-with-spl.sfp" 31 32 /* 33 * Memory configurations 34 */ 35 #define CONFIG_NR_DRAM_BANKS 1 36 #define PHYS_SDRAM_1 0x0 37 #define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024) 38 #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 39 #define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE 40 41 #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 42 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 43 #define CONFIG_SYS_INIT_SP_OFFSET \ 44 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 45 #define CONFIG_SYS_INIT_SP_ADDR \ 46 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 47 48 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 49 #ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET 50 #define CONFIG_SYS_TEXT_BASE 0x08000040 51 #else 52 #define CONFIG_SYS_TEXT_BASE 0x01000040 53 #endif 54 55 /* 56 * U-Boot general configurations 57 */ 58 #define CONFIG_SYS_LONGHELP 59 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ 60 #define CONFIG_SYS_PBSIZE \ 61 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 62 /* Print buffer size */ 63 #define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ 64 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 65 /* Boot argument buffer size */ 66 #define CONFIG_AUTO_COMPLETE /* Command auto complete */ 67 #define CONFIG_CMDLINE_EDITING /* Command history etc */ 68 69 #ifndef CONFIG_SYS_HOSTNAME 70 #define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD 71 #endif 72 73 /* 74 * Cache 75 */ 76 #define CONFIG_SYS_L2_PL310 77 #define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS 78 79 /* 80 * SDRAM controller 81 */ 82 #define CONFIG_ALTERA_SDRAM 83 84 /* 85 * EPCS/EPCQx1 Serial Flash Controller 86 */ 87 #ifdef CONFIG_ALTERA_SPI 88 #define CONFIG_SF_DEFAULT_SPEED 30000000 89 /* 90 * The base address is configurable in QSys, each board must specify the 91 * base address based on it's particular FPGA configuration. Please note 92 * that the address here is incremented by 0x400 from the Base address 93 * selected in QSys, since the SPI registers are at offset +0x400. 94 * #define CONFIG_SYS_SPI_BASE 0xff240400 95 */ 96 #endif 97 98 /* 99 * Ethernet on SoC (EMAC) 100 */ 101 #if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET) 102 #define CONFIG_DW_ALTDESCRIPTOR 103 #define CONFIG_MII 104 #define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ) 105 #define CONFIG_PHY_GIGE 106 #endif 107 108 /* 109 * FPGA Driver 110 */ 111 #ifdef CONFIG_CMD_FPGA 112 #define CONFIG_FPGA 113 #define CONFIG_FPGA_ALTERA 114 #define CONFIG_FPGA_SOCFPGA 115 #define CONFIG_FPGA_COUNT 1 116 #endif 117 118 /* 119 * L4 OSC1 Timer 0 120 */ 121 /* This timer uses eosc1, whose clock frequency is fixed at any condition. */ 122 #define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS 123 #define CONFIG_SYS_TIMER_COUNTS_DOWN 124 #define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) 125 #ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET 126 #define CONFIG_SYS_TIMER_RATE 2400000 127 #else 128 #define CONFIG_SYS_TIMER_RATE 25000000 129 #endif 130 131 /* 132 * L4 Watchdog 133 */ 134 #ifdef CONFIG_HW_WATCHDOG 135 #define CONFIG_DESIGNWARE_WATCHDOG 136 #define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS 137 #define CONFIG_DW_WDT_CLOCK_KHZ 25000 138 #define CONFIG_HW_WATCHDOG_TIMEOUT_MS 30000 139 #endif 140 141 /* 142 * MMC Driver 143 */ 144 #ifdef CONFIG_CMD_MMC 145 #define CONFIG_BOUNCE_BUFFER 146 #define CONFIG_GENERIC_MMC 147 #define CONFIG_DWMMC 148 #define CONFIG_SOCFPGA_DWMMC 149 #define CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH 1024 150 /* FIXME */ 151 /* using smaller max blk cnt to avoid flooding the limited stack we have */ 152 #define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */ 153 #endif 154 155 /* 156 * NAND Support 157 */ 158 #ifdef CONFIG_NAND_DENALI 159 #define CONFIG_SYS_MAX_NAND_DEVICE 1 160 #define CONFIG_SYS_NAND_MAX_CHIPS 1 161 #define CONFIG_SYS_NAND_ONFI_DETECTION 162 #define CONFIG_NAND_DENALI_ECC_SIZE 512 163 #define CONFIG_SYS_NAND_REGS_BASE SOCFPGA_NANDREGS_ADDRESS 164 #define CONFIG_SYS_NAND_DATA_BASE SOCFPGA_NANDDATA_ADDRESS 165 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10) 166 #endif 167 168 /* 169 * I2C support 170 */ 171 #define CONFIG_SYS_I2C 172 #define CONFIG_SYS_I2C_BUS_MAX 4 173 #define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS 174 #define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS 175 #define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS 176 #define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS 177 /* Using standard mode which the speed up to 100Kb/s */ 178 #define CONFIG_SYS_I2C_SPEED 100000 179 #define CONFIG_SYS_I2C_SPEED1 100000 180 #define CONFIG_SYS_I2C_SPEED2 100000 181 #define CONFIG_SYS_I2C_SPEED3 100000 182 /* Address of device when used as slave */ 183 #define CONFIG_SYS_I2C_SLAVE 0x02 184 #define CONFIG_SYS_I2C_SLAVE1 0x02 185 #define CONFIG_SYS_I2C_SLAVE2 0x02 186 #define CONFIG_SYS_I2C_SLAVE3 0x02 187 #ifndef __ASSEMBLY__ 188 /* Clock supplied to I2C controller in unit of MHz */ 189 unsigned int cm_get_l4_sp_clk_hz(void); 190 #define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000) 191 #endif 192 193 /* 194 * QSPI support 195 */ 196 /* Enable multiple SPI NOR flash manufacturers */ 197 #ifndef CONFIG_SPL_BUILD 198 #define CONFIG_SPI_FLASH_MTD 199 #define CONFIG_CMD_MTDPARTS 200 #define CONFIG_MTD_DEVICE 201 #define CONFIG_MTD_PARTITIONS 202 #define MTDIDS_DEFAULT "nor0=ff705000.spi.0" 203 #endif 204 /* QSPI reference clock */ 205 #ifndef __ASSEMBLY__ 206 unsigned int cm_get_qspi_controller_clk_hz(void); 207 #define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz() 208 #endif 209 #define CONFIG_CQSPI_DECODER 0 210 #define CONFIG_BOUNCE_BUFFER 211 212 /* 213 * Designware SPI support 214 */ 215 216 /* 217 * Serial Driver 218 */ 219 #define CONFIG_SYS_NS16550_SERIAL 220 #define CONFIG_SYS_NS16550_REG_SIZE -4 221 #define CONFIG_SYS_NS16550_COM1 SOCFPGA_UART0_ADDRESS 222 #ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET 223 #define CONFIG_SYS_NS16550_CLK 1000000 224 #else 225 #define CONFIG_SYS_NS16550_CLK 100000000 226 #endif 227 #define CONFIG_CONS_INDEX 1 228 #define CONFIG_BAUDRATE 115200 229 230 /* 231 * USB 232 */ 233 #ifdef CONFIG_CMD_USB 234 #define CONFIG_USB_DWC2 235 #endif 236 237 /* 238 * USB Gadget (DFU, UMS) 239 */ 240 #if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE) 241 #define CONFIG_USB_FUNCTION_MASS_STORAGE 242 243 #define CONFIG_SYS_DFU_DATA_BUF_SIZE (32 * 1024 * 1024) 244 #define DFU_DEFAULT_POLL_TIMEOUT 300 245 246 /* USB IDs */ 247 #define CONFIG_G_DNL_UMS_VENDOR_NUM 0x0525 248 #define CONFIG_G_DNL_UMS_PRODUCT_NUM 0xA4A5 249 #endif 250 251 /* 252 * U-Boot environment 253 */ 254 #if !defined(CONFIG_ENV_SIZE) 255 #define CONFIG_ENV_SIZE 4096 256 #endif 257 258 /* Environment for SDMMC boot */ 259 #if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET) 260 #define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */ 261 #define CONFIG_ENV_OFFSET 512 /* just after the MBR */ 262 #endif 263 264 /* Environment for QSPI boot */ 265 #if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_OFFSET) 266 #define CONFIG_ENV_OFFSET 0x00100000 267 #define CONFIG_ENV_SECT_SIZE (64 * 1024) 268 #endif 269 270 /* 271 * mtd partitioning for serial NOR flash 272 * 273 * device nor0 <ff705000.spi.0>, # parts = 6 274 * #: name size offset mask_flags 275 * 0: u-boot 0x00100000 0x00000000 0 276 * 1: env1 0x00040000 0x00100000 0 277 * 2: env2 0x00040000 0x00140000 0 278 * 3: UBI 0x03e80000 0x00180000 0 279 * 4: boot 0x00e80000 0x00180000 0 280 * 5: rootfs 0x01000000 0x01000000 0 281 * 282 */ 283 #if defined(CONFIG_CMD_SF) && !defined(MTDPARTS_DEFAULT) 284 #define MTDPARTS_DEFAULT "mtdparts=ff705000.spi.0:"\ 285 "1m(u-boot)," \ 286 "256k(env1)," \ 287 "256k(env2)," \ 288 "14848k(boot)," \ 289 "16m(rootfs)," \ 290 "-@1536k(UBI)\0" 291 #endif 292 293 /* UBI and UBIFS support */ 294 #if defined(CONFIG_CMD_SF) || defined(CONFIG_CMD_NAND) 295 #define CONFIG_CMD_UBIFS 296 #define CONFIG_RBTREE 297 #define CONFIG_LZO 298 #endif 299 300 /* 301 * SPL 302 * 303 * SRAM Memory layout: 304 * 305 * 0xFFFF_0000 ...... Start of SRAM 306 * 0xFFFF_xxxx ...... Top of stack (grows down) 307 * 0xFFFF_yyyy ...... Malloc area 308 * 0xFFFF_zzzz ...... Global Data 309 * 0xFFFF_FF00 ...... End of SRAM 310 */ 311 #define CONFIG_SPL_FRAMEWORK 312 #define CONFIG_SPL_RAM_DEVICE 313 #define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR 314 #define CONFIG_SPL_MAX_SIZE (64 * 1024) 315 316 /* SPL SDMMC boot support */ 317 #ifdef CONFIG_SPL_MMC_SUPPORT 318 #if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT) 319 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 2 320 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img" 321 #else 322 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1 323 #endif 324 #endif 325 326 /* SPL QSPI boot support */ 327 #ifdef CONFIG_SPL_SPI_SUPPORT 328 #define CONFIG_SPL_SPI_LOAD 329 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000 330 #endif 331 332 /* SPL NAND boot support */ 333 #ifdef CONFIG_SPL_NAND_SUPPORT 334 #define CONFIG_SYS_NAND_USE_FLASH_BBT 335 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 336 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 337 #endif 338 339 /* 340 * Stack setup 341 */ 342 #define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR 343 344 #endif /* __CONFIG_SOCFPGA_COMMON_H__ */ 345