1 /*
2  * Bluewater Systems Snapper 9260 and 9G20 modules
3  *
4  * (C) Copyright 2011 Bluewater Systems
5  *   Author: Andre Renaud <andre@bluewatersys.com>
6  *   Author: Ryan Mallon <ryan@bluewatersys.com>
7  *
8  * SPDX-License-Identifier:	GPL-2.0+
9  */
10 
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /* SoC type is defined in boards.cfg */
15 #include <asm/hardware.h>
16 #include <linux/sizes.h>
17 
18 #define CONFIG_SYS_TEXT_BASE		0x21f00000
19 
20 /* ARM asynchronous clock */
21 #define CONFIG_SYS_AT91_MAIN_CLOCK	18432000 /* External Crystal, in Hz */
22 #define CONFIG_SYS_AT91_SLOW_CLOCK	32768
23 #define CONFIG_SYS_GENERIC_BOARD
24 
25 /* CPU */
26 #define CONFIG_ARCH_CPU_INIT
27 
28 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs	*/
29 #define CONFIG_SETUP_MEMORY_TAGS
30 #define CONFIG_INITRD_TAG
31 #define CONFIG_SKIP_LOWLEVEL_INIT
32 #define CONFIG_DISPLAY_CPUINFO
33 #define CONFIG_FIT
34 
35 /* SDRAM */
36 #define CONFIG_NR_DRAM_BANKS		1
37 #define CONFIG_SYS_SDRAM_BASE		ATMEL_BASE_CS1
38 #define CONFIG_SYS_SDRAM_SIZE		(64 * 1024 * 1024) /* 64MB */
39 #define CONFIG_SYS_INIT_SP_ADDR		(ATMEL_BASE_SRAM1 + 0x1000 - \
40 					 GENERATED_GBL_DATA_SIZE)
41 
42 /* Mem test settings */
43 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
44 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + (1024 * 1024))
45 
46 /* NAND Flash */
47 #define CONFIG_NAND_ATMEL
48 #define CONFIG_SYS_NO_FLASH
49 #define CONFIG_SYS_MAX_NAND_DEVICE	1
50 #define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
51 #define CONFIG_SYS_NAND_DBW_8
52 #define CONFIG_SYS_NAND_MASK_ALE	(1 << 21) /* AD21 */
53 #define CONFIG_SYS_NAND_MASK_CLE	(1 << 22) /* AD22 */
54 #define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PC14
55 #define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PC13
56 
57 /* Ethernet */
58 #define CONFIG_MACB
59 #define CONFIG_RMII
60 #define CONFIG_NET_RETRY_COUNT		20
61 #define CONFIG_RESET_PHY_R
62 #define CONFIG_AT91_WANTS_COMMON_PHY
63 #define CONFIG_TFTP_PORT
64 #define CONFIG_TFTP_TSIZE
65 
66 /* USB */
67 #define CONFIG_USB_ATMEL
68 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB
69 #define CONFIG_USB_OHCI_NEW
70 #define CONFIG_DOS_PARTITION
71 #define CONFIG_SYS_USB_OHCI_CPU_INIT
72 #define CONFIG_SYS_USB_OHCI_REGS_BASE	ATMEL_UHP_BASE
73 #define CONFIG_SYS_USB_OHCI_SLOT_NAME	"at91sam9260"
74 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
75 #define CONFIG_USB_STORAGE
76 
77 /* GPIOs and IO expander */
78 #define CONFIG_ATMEL_LEGACY
79 #define CONFIG_AT91_GPIO
80 #define CONFIG_AT91_GPIO_PULLUP		1
81 #define CONFIG_PCA953X
82 #define CONFIG_SYS_I2C_PCA953X_ADDR	0x28
83 #define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x28, 16} }
84 
85 /* UARTs/Serial console */
86 #define CONFIG_ATMEL_USART
87 #ifndef CONFIG_DM_SERIAL
88 #define CONFIG_USART_BASE		ATMEL_BASE_DBGU
89 #define CONFIG_USART_ID			ATMEL_ID_SYS
90 #endif
91 #define CONFIG_BAUDRATE			115200
92 #define CONFIG_SYS_PROMPT		"Snapper> "
93 
94 /* I2C - Bit-bashed */
95 #define CONFIG_SYS_I2C
96 #define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
97 #define CONFIG_SYS_I2C_SOFT_SPEED	100000
98 #define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
99 #define CONFIG_SOFT_I2C_READ_REPEATED_START
100 #define I2C_INIT do {							\
101 		at91_set_gpio_output(AT91_PIN_PA23, 1);			\
102 		at91_set_gpio_output(AT91_PIN_PA24, 1);			\
103 		at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1);	\
104 		at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1);	\
105 	} while (0)
106 #define I2C_SOFT_DECLARATIONS
107 #define I2C_ACTIVE
108 #define I2C_TRISTATE	at91_set_gpio_input(AT91_PIN_PA23, 1);
109 #define I2C_READ	at91_get_gpio_value(AT91_PIN_PA23);
110 #define I2C_SDA(bit) do {						\
111 		if (bit) {						\
112 			at91_set_gpio_input(AT91_PIN_PA23, 1);		\
113 		} else {						\
114 			at91_set_gpio_output(AT91_PIN_PA23, 1);		\
115 			at91_set_gpio_value(AT91_PIN_PA23, bit);	\
116 		}							\
117 	} while (0)
118 #define I2C_SCL(bit)	at91_set_pio_value(AT91_PIO_PORTA, 24, bit)
119 #define I2C_DELAY	udelay(2)
120 
121 /* Boot options */
122 #define CONFIG_SYS_LOAD_ADDR		0x23000000
123 #define CONFIG_BOOTDELAY		3
124 #define CONFIG_ZERO_BOOTDELAY_CHECK
125 
126 #define CONFIG_BOOTP_BOOTFILESIZE
127 #define CONFIG_BOOTP_BOOTPATH
128 #define CONFIG_BOOTP_GATEWAY
129 #define CONFIG_BOOTP_HOSTNAME
130 
131 /* Environment settings */
132 #define CONFIG_ENV_IS_IN_NAND
133 #define CONFIG_ENV_OFFSET		(512 << 10)
134 #define CONFIG_ENV_SIZE			(256 << 10)
135 #define CONFIG_ENV_OVERWRITE
136 #define CONFIG_BOOTARGS			"console=ttyS0,115200 ip=any"
137 
138 /* Console settings */
139 #define CONFIG_SYS_CBSIZE		256
140 #define CONFIG_SYS_MAXARGS		16
141 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE +		\
142 					 sizeof(CONFIG_SYS_PROMPT) + 16)
143 #define CONFIG_SYS_LONGHELP
144 #define CONFIG_CMDLINE_EDITING
145 #define CONFIG_AUTO_COMPLETE
146 #define CONFIG_SYS_HUSH_PARSER
147 
148 /* U-Boot memory settings */
149 #define CONFIG_SYS_MALLOC_LEN		(1 << 20)
150 
151 /* Command line configuration */
152 #include <config_cmd_default.h>
153 #undef CONFIG_CMD_BDI
154 #undef CONFIG_CMD_FPGA
155 #undef CONFIG_CMD_IMI
156 #undef CONFIG_CMD_IMLS
157 #undef CONFIG_CMD_LOADS
158 #undef CONFIG_CMD_SOURCE
159 
160 #define CONFIG_CMD_PING
161 #define CONFIG_CMD_DHCP
162 #define CONFIG_CMD_FAT
163 #define CONFIG_CMD_I2C
164 #define CONFIG_CMD_GPIO
165 #define CONFIG_CMD_USB
166 #define CONFIG_CMD_MII
167 #define CONFIG_CMD_NAND
168 #define CONFIG_CMD_PCA953X
169 #define CONFIG_CMD_PCA953X_INFO
170 
171 #endif /* __CONFIG_H */
172