1 /*
2  * Bluewater Systems Snapper 9260 and 9G20 modules
3  *
4  * (C) Copyright 2011 Bluewater Systems
5  *   Author: Andre Renaud <andre@bluewatersys.com>
6  *   Author: Ryan Mallon <ryan@bluewatersys.com>
7  *
8  * SPDX-License-Identifier:	GPL-2.0+
9  */
10 
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /* SoC type is defined in boards.cfg */
15 #include <asm/hardware.h>
16 #include <linux/sizes.h>
17 
18 #define CONFIG_SYS_TEXT_BASE		0x21f00000
19 
20 /* ARM asynchronous clock */
21 #define CONFIG_SYS_AT91_MAIN_CLOCK	18432000 /* External Crystal, in Hz */
22 #define CONFIG_SYS_AT91_SLOW_CLOCK	32768
23 
24 /* CPU */
25 #define CONFIG_ARCH_CPU_INIT
26 
27 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs	*/
28 #define CONFIG_SETUP_MEMORY_TAGS
29 #define CONFIG_INITRD_TAG
30 #define CONFIG_SKIP_LOWLEVEL_INIT
31 #define CONFIG_DISPLAY_CPUINFO
32 
33 /* SDRAM */
34 #define CONFIG_NR_DRAM_BANKS		1
35 #define CONFIG_SYS_SDRAM_BASE		ATMEL_BASE_CS1
36 #define CONFIG_SYS_SDRAM_SIZE		(64 * 1024 * 1024) /* 64MB */
37 #define CONFIG_SYS_INIT_SP_ADDR		(ATMEL_BASE_SRAM1 + 0x1000 - \
38 					 GENERATED_GBL_DATA_SIZE)
39 
40 /* Mem test settings */
41 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
42 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + (1024 * 1024))
43 
44 /* NAND Flash */
45 #define CONFIG_NAND_ATMEL
46 #define CONFIG_SYS_NO_FLASH
47 #define CONFIG_SYS_MAX_NAND_DEVICE	1
48 #define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
49 #define CONFIG_SYS_NAND_DBW_8
50 #define CONFIG_SYS_NAND_MASK_ALE	(1 << 21) /* AD21 */
51 #define CONFIG_SYS_NAND_MASK_CLE	(1 << 22) /* AD22 */
52 #define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PC14
53 #define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PC13
54 
55 /* Ethernet */
56 #define CONFIG_MACB
57 #define CONFIG_RMII
58 #define CONFIG_NET_RETRY_COUNT		20
59 #define CONFIG_RESET_PHY_R
60 #define CONFIG_AT91_WANTS_COMMON_PHY
61 #define CONFIG_TFTP_PORT
62 #define CONFIG_TFTP_TSIZE
63 
64 /* USB */
65 #define CONFIG_USB_ATMEL
66 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB
67 #define CONFIG_USB_OHCI_NEW
68 #define CONFIG_DOS_PARTITION
69 #define CONFIG_SYS_USB_OHCI_CPU_INIT
70 #define CONFIG_SYS_USB_OHCI_REGS_BASE	ATMEL_UHP_BASE
71 #define CONFIG_SYS_USB_OHCI_SLOT_NAME	"at91sam9260"
72 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
73 #define CONFIG_USB_STORAGE
74 
75 /* GPIOs and IO expander */
76 #define CONFIG_ATMEL_LEGACY
77 #define CONFIG_AT91_GPIO
78 #define CONFIG_AT91_GPIO_PULLUP		1
79 #define CONFIG_PCA953X
80 #define CONFIG_SYS_I2C_PCA953X_ADDR	0x28
81 #define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x28, 16} }
82 
83 /* UARTs/Serial console */
84 #define CONFIG_ATMEL_USART
85 #ifndef CONFIG_DM_SERIAL
86 #define CONFIG_USART_BASE		ATMEL_BASE_DBGU
87 #define CONFIG_USART_ID			ATMEL_ID_SYS
88 #endif
89 #define CONFIG_BAUDRATE			115200
90 
91 /* I2C - Bit-bashed */
92 #define CONFIG_SYS_I2C
93 #define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
94 #define CONFIG_SYS_I2C_SOFT_SPEED	100000
95 #define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
96 #define CONFIG_SOFT_I2C_READ_REPEATED_START
97 #define I2C_INIT do {							\
98 		at91_set_gpio_output(AT91_PIN_PA23, 1);			\
99 		at91_set_gpio_output(AT91_PIN_PA24, 1);			\
100 		at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1);	\
101 		at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1);	\
102 	} while (0)
103 #define I2C_SOFT_DECLARATIONS
104 #define I2C_ACTIVE
105 #define I2C_TRISTATE	at91_set_gpio_input(AT91_PIN_PA23, 1);
106 #define I2C_READ	at91_get_gpio_value(AT91_PIN_PA23);
107 #define I2C_SDA(bit) do {						\
108 		if (bit) {						\
109 			at91_set_gpio_input(AT91_PIN_PA23, 1);		\
110 		} else {						\
111 			at91_set_gpio_output(AT91_PIN_PA23, 1);		\
112 			at91_set_gpio_value(AT91_PIN_PA23, bit);	\
113 		}							\
114 	} while (0)
115 #define I2C_SCL(bit)	at91_set_pio_value(AT91_PIO_PORTA, 24, bit)
116 #define I2C_DELAY	udelay(2)
117 
118 /* Boot options */
119 #define CONFIG_SYS_LOAD_ADDR		0x23000000
120 #define CONFIG_BOOTDELAY		3
121 #define CONFIG_ZERO_BOOTDELAY_CHECK
122 
123 #define CONFIG_BOOTP_BOOTFILESIZE
124 #define CONFIG_BOOTP_BOOTPATH
125 #define CONFIG_BOOTP_GATEWAY
126 #define CONFIG_BOOTP_HOSTNAME
127 
128 /* Environment settings */
129 #define CONFIG_ENV_IS_IN_NAND
130 #define CONFIG_ENV_OFFSET		(512 << 10)
131 #define CONFIG_ENV_SIZE			(256 << 10)
132 #define CONFIG_ENV_OVERWRITE
133 #define CONFIG_BOOTARGS			"console=ttyS0,115200 ip=any"
134 
135 /* Console settings */
136 #define CONFIG_SYS_CBSIZE		256
137 #define CONFIG_SYS_MAXARGS		16
138 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE +		\
139 					 sizeof(CONFIG_SYS_PROMPT) + 16)
140 #define CONFIG_SYS_LONGHELP
141 #define CONFIG_CMDLINE_EDITING
142 #define CONFIG_AUTO_COMPLETE
143 #define CONFIG_SYS_HUSH_PARSER
144 
145 /* U-Boot memory settings */
146 #define CONFIG_SYS_MALLOC_LEN		(1 << 20)
147 
148 /* Command line configuration */
149 #define CONFIG_CMD_PING
150 #define CONFIG_CMD_DHCP
151 #define CONFIG_CMD_FAT
152 #define CONFIG_CMD_I2C
153 #define CONFIG_CMD_USB
154 #define CONFIG_CMD_MII
155 #define CONFIG_CMD_NAND
156 #define CONFIG_CMD_PCA953X
157 #define CONFIG_CMD_PCA953X_INFO
158 
159 #endif /* __CONFIG_H */
160