1 /* 2 * Copyright 2007 Wind River Systems <www.windriver.com> 3 * Copyright 2007 Embedded Specialties, Inc. 4 * Joe Hamman <joe.hamman@embeddedspecialties.com> 5 * 6 * Copyright 2006 Freescale Semiconductor. 7 * 8 * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 /* 14 * SBC8641D board configuration file 15 * 16 * Make sure you change the MAC address and other network params first, 17 * search for CONFIG_SERVERIP, etc in this file. 18 */ 19 20 #ifndef __CONFIG_H 21 #define __CONFIG_H 22 23 /* High Level Configuration Options */ 24 #define CONFIG_SBC8641D 1 /* SBC8641D board specific */ 25 #define CONFIG_MP 1 /* support multiple processors */ 26 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 27 28 #define CONFIG_SYS_TEXT_BASE 0xfff00000 29 30 #ifdef RUN_DIAG 31 #define CONFIG_SYS_DIAG_ADDR 0xff800000 32 #endif 33 34 #define CONFIG_SYS_RESET_ADDRESS 0xfff00100 35 36 /* 37 * virtual address to be used for temporary mappings. There 38 * should be 128k free at this VA. 39 */ 40 #define CONFIG_SYS_SCRATCH_VA 0xe8000000 41 42 #define CONFIG_SYS_SRIO 43 #define CONFIG_SRIO1 /* SRIO port 1 */ 44 45 #define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */ 46 #define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */ 47 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 48 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 49 50 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 51 #define CONFIG_ENV_OVERWRITE 52 53 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 54 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 55 56 #undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/ 57 #undef CONFIG_DDR_ECC /* only for ECC DDR module */ 58 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 59 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 60 #define CONFIG_NUM_DDR_CONTROLLERS 2 61 #define CACHE_LINE_INTERLEAVING 0x20000000 62 #define PAGE_INTERLEAVING 0x21000000 63 #define BANK_INTERLEAVING 0x22000000 64 #define SUPER_BANK_INTERLEAVING 0x23000000 65 66 #define CONFIG_ALTIVEC 1 67 68 /* 69 * L2CR setup -- make sure this is right for your board! 70 */ 71 #define CONFIG_SYS_L2 72 #define L2_INIT 0 73 #define L2_ENABLE (L2CR_L2E) 74 75 #ifndef CONFIG_SYS_CLK_FREQ 76 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 77 #endif 78 79 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 80 81 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 82 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 83 #define CONFIG_SYS_MEMTEST_END 0x00400000 84 85 /* 86 * Base addresses -- Note these are effective addresses where the 87 * actual resources get mapped (not physical addresses) 88 */ 89 #define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ 90 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 91 92 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 93 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 94 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW 95 96 /* 97 * DDR Setup 98 */ 99 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ 100 #define CONFIG_SYS_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */ 101 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 102 #define CONFIG_SYS_SDRAM_BASE2 CONFIG_SYS_DDR_SDRAM_BASE2 103 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 104 #define CONFIG_VERY_BIG_RAM 105 106 #define CONFIG_NUM_DDR_CONTROLLERS 2 107 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 108 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 109 110 #if defined(CONFIG_SPD_EEPROM) 111 /* 112 * Determine DDR configuration from I2C interface. 113 */ 114 #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */ 115 #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */ 116 #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */ 117 #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */ 118 119 #else 120 /* 121 * Manually set up DDR1 & DDR2 parameters 122 */ 123 124 #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ 125 126 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 127 #define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 128 #define CONFIG_SYS_DDR_CS2_BNDS 0x00000000 129 #define CONFIG_SYS_DDR_CS3_BNDS 0x00000000 130 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 131 #define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 132 #define CONFIG_SYS_DDR_CS2_CONFIG 0x00000000 133 #define CONFIG_SYS_DDR_CS3_CONFIG 0x00000000 134 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 135 #define CONFIG_SYS_DDR_TIMING_0 0x00220802 136 #define CONFIG_SYS_DDR_TIMING_1 0x38377322 137 #define CONFIG_SYS_DDR_TIMING_2 0x002040c7 138 #define CONFIG_SYS_DDR_CFG_1A 0x43008008 139 #define CONFIG_SYS_DDR_CFG_2 0x24401000 140 #define CONFIG_SYS_DDR_MODE_1 0x23c00542 141 #define CONFIG_SYS_DDR_MODE_2 0x00000000 142 #define CONFIG_SYS_DDR_MODE_CTL 0x00000000 143 #define CONFIG_SYS_DDR_INTERVAL 0x05080100 144 #define CONFIG_SYS_DDR_DATA_INIT 0x00000000 145 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 146 #define CONFIG_SYS_DDR_CFG_1B 0xC3008008 147 148 #define CONFIG_SYS_DDR2_CS0_BNDS 0x0010001F 149 #define CONFIG_SYS_DDR2_CS1_BNDS 0x00000000 150 #define CONFIG_SYS_DDR2_CS2_BNDS 0x00000000 151 #define CONFIG_SYS_DDR2_CS3_BNDS 0x00000000 152 #define CONFIG_SYS_DDR2_CS0_CONFIG 0x80010102 153 #define CONFIG_SYS_DDR2_CS1_CONFIG 0x00000000 154 #define CONFIG_SYS_DDR2_CS2_CONFIG 0x00000000 155 #define CONFIG_SYS_DDR2_CS3_CONFIG 0x00000000 156 #define CONFIG_SYS_DDR2_EXT_REFRESH 0x00000000 157 #define CONFIG_SYS_DDR2_TIMING_0 0x00220802 158 #define CONFIG_SYS_DDR2_TIMING_1 0x38377322 159 #define CONFIG_SYS_DDR2_TIMING_2 0x002040c7 160 #define CONFIG_SYS_DDR2_CFG_1A 0x43008008 161 #define CONFIG_SYS_DDR2_CFG_2 0x24401000 162 #define CONFIG_SYS_DDR2_MODE_1 0x23c00542 163 #define CONFIG_SYS_DDR2_MODE_2 0x00000000 164 #define CONFIG_SYS_DDR2_MODE_CTL 0x00000000 165 #define CONFIG_SYS_DDR2_INTERVAL 0x05080100 166 #define CONFIG_SYS_DDR2_DATA_INIT 0x00000000 167 #define CONFIG_SYS_DDR2_CLK_CTRL 0x03800000 168 #define CONFIG_SYS_DDR2_CFG_1B 0xC3008008 169 170 #endif 171 172 /* #define CONFIG_ID_EEPROM 1 173 #define ID_EEPROM_ADDR 0x57 */ 174 175 /* 176 * The SBC8641D contains 16MB flash space at ff000000. 177 */ 178 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ 179 180 /* Flash */ 181 #define CONFIG_SYS_BR0_PRELIM 0xff001001 /* port size 16bit */ 182 #define CONFIG_SYS_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */ 183 184 /* 64KB EEPROM */ 185 #define CONFIG_SYS_BR1_PRELIM 0xf0000801 /* port size 16bit */ 186 #define CONFIG_SYS_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */ 187 188 /* EPLD - User switches, board id, LEDs */ 189 #define CONFIG_SYS_BR2_PRELIM 0xf1000801 /* port size 16bit */ 190 #define CONFIG_SYS_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */ 191 192 /* Local bus SDRAM 128MB */ 193 #define CONFIG_SYS_BR3_PRELIM 0xe0001861 /* port size ?bit */ 194 #define CONFIG_SYS_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */ 195 #define CONFIG_SYS_BR4_PRELIM 0xe4001861 /* port size ?bit */ 196 #define CONFIG_SYS_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */ 197 198 /* Disk on Chip (DOC) 128MB */ 199 #define CONFIG_SYS_BR5_PRELIM 0xe8001001 /* port size ?bit */ 200 #define CONFIG_SYS_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */ 201 202 /* LCD */ 203 #define CONFIG_SYS_BR6_PRELIM 0xf4000801 /* port size ?bit */ 204 #define CONFIG_SYS_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ 205 206 /* Control logic & misc peripherals */ 207 #define CONFIG_SYS_BR7_PRELIM 0xf2000801 /* port size ?bit */ 208 #define CONFIG_SYS_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ 209 210 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 211 #define CONFIG_SYS_MAX_FLASH_SECT 131 /* sectors per device */ 212 213 #undef CONFIG_SYS_FLASH_CHECKSUM 214 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 215 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 216 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 217 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 218 219 #define CONFIG_FLASH_CFI_DRIVER 220 #define CONFIG_SYS_FLASH_CFI 221 #define CONFIG_SYS_WRITE_SWAPPED_DATA 222 #define CONFIG_SYS_FLASH_EMPTY_INFO 223 #define CONFIG_SYS_FLASH_PROTECTION 224 225 #undef CONFIG_CLOCKS_IN_MHZ 226 227 #define CONFIG_SYS_INIT_RAM_LOCK 1 228 #ifndef CONFIG_SYS_INIT_RAM_LOCK 229 #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ 230 #else 231 #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ 232 #endif 233 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 234 235 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 236 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 237 238 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 239 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 240 241 /* Serial Port */ 242 #define CONFIG_CONS_INDEX 1 243 #define CONFIG_SYS_NS16550_SERIAL 244 #define CONFIG_SYS_NS16550_REG_SIZE 1 245 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 246 247 #define CONFIG_SYS_BAUDRATE_TABLE \ 248 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 249 250 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 251 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 252 253 /* 254 * I2C 255 */ 256 #define CONFIG_SYS_I2C 257 #define CONFIG_SYS_I2C_FSL 258 #define CONFIG_SYS_FSL_I2C_SPEED 400000 259 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 260 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 261 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 262 263 /* 264 * RapidIO MMU 265 */ 266 #define CONFIG_SYS_SRIO1_MEM_BASE 0xc0000000 /* base address */ 267 #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BASE 268 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ 269 270 /* 271 * General PCI 272 * Addresses are mapped 1-1. 273 */ 274 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 275 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 276 #define CONFIG_SYS_PCIE1_MEM_VIRT CONFIG_SYS_PCIE1_MEM_BUS 277 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 278 #define CONFIG_SYS_PCIE1_IO_BUS 0xe2000000 279 #define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BUS 280 #define CONFIG_SYS_PCIE1_IO_VIRT CONFIG_SYS_PCIE1_IO_BUS 281 #define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */ 282 283 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 284 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 285 #define CONFIG_SYS_PCIE2_MEM_VIRT CONFIG_SYS_PCIE2_MEM_BUS 286 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 287 #define CONFIG_SYS_PCIE2_IO_BUS 0xe3000000 288 #define CONFIG_SYS_PCIE2_IO_PHYS CONFIG_SYS_PCIE2_IO_BUS 289 #define CONFIG_SYS_PCIE2_IO_VIRT CONFIG_SYS_PCIE2_IO_BUS 290 #define CONFIG_SYS_PCIE2_IO_SIZE 0x1000000 /* 16M */ 291 292 #if defined(CONFIG_PCI) 293 294 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 295 296 #undef CONFIG_EEPRO100 297 #undef CONFIG_TULIP 298 299 #if !defined(CONFIG_PCI_PNP) 300 #define PCI_ENET0_IOADDR 0xe0000000 301 #define PCI_ENET0_MEMADDR 0xe0000000 302 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 303 #endif 304 305 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 306 307 #define CONFIG_DOS_PARTITION 308 #undef CONFIG_SCSI_AHCI 309 310 #ifdef CONFIG_SCSI_AHCI 311 #define CONFIG_SATA_ULI5288 312 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 313 #define CONFIG_SYS_SCSI_MAX_LUN 1 314 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 315 #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE 316 #endif 317 318 #endif /* CONFIG_PCI */ 319 320 #if defined(CONFIG_TSEC_ENET) 321 322 /* #define CONFIG_MII 1 */ /* MII PHY management */ 323 324 #define CONFIG_TSEC1 1 325 #define CONFIG_TSEC1_NAME "eTSEC1" 326 #define CONFIG_TSEC2 1 327 #define CONFIG_TSEC2_NAME "eTSEC2" 328 #define CONFIG_TSEC3 1 329 #define CONFIG_TSEC3_NAME "eTSEC3" 330 #define CONFIG_TSEC4 1 331 #define CONFIG_TSEC4_NAME "eTSEC4" 332 333 #define TSEC1_PHY_ADDR 0x1F 334 #define TSEC2_PHY_ADDR 0x00 335 #define TSEC3_PHY_ADDR 0x01 336 #define TSEC4_PHY_ADDR 0x02 337 #define TSEC1_PHYIDX 0 338 #define TSEC2_PHYIDX 0 339 #define TSEC3_PHYIDX 0 340 #define TSEC4_PHYIDX 0 341 #define TSEC1_FLAGS TSEC_GIGABIT 342 #define TSEC2_FLAGS TSEC_GIGABIT 343 #define TSEC3_FLAGS TSEC_GIGABIT 344 #define TSEC4_FLAGS TSEC_GIGABIT 345 346 #define CONFIG_SYS_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */ 347 348 #define CONFIG_ETHPRIME "eTSEC1" 349 350 #endif /* CONFIG_TSEC_ENET */ 351 352 /* 353 * BAT0 2G Cacheable, non-guarded 354 * 0x0000_0000 2G DDR 355 */ 356 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 357 #define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) 358 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) 359 #define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U 360 361 /* 362 * BAT1 1G Cache-inhibited, guarded 363 * 0x8000_0000 512M PCI-Express 1 Memory 364 * 0xa000_0000 512M PCI-Express 2 Memory 365 * Changed it for operating from 0xd0000000 366 */ 367 #define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW \ 368 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 369 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP) 370 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 371 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 372 373 /* 374 * BAT2 512M Cache-inhibited, guarded 375 * 0xc000_0000 512M RapidIO Memory 376 */ 377 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_SRIO1_MEM_BASE | BATL_PP_RW \ 378 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 379 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP) 380 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_SRIO1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) 381 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 382 383 /* 384 * BAT3 4M Cache-inhibited, guarded 385 * 0xf800_0000 4M CCSR 386 */ 387 #define CONFIG_SYS_DBAT3L ( CONFIG_SYS_CCSRBAR | BATL_PP_RW \ 388 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 389 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) 390 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) 391 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 392 393 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 394 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 395 | BATL_PP_RW | BATL_CACHEINHIBIT \ 396 | BATL_GUARDEDSTORAGE) 397 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 398 | BATU_BL_1M | BATU_VS | BATU_VP) 399 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 400 | BATL_PP_RW | BATL_CACHEINHIBIT) 401 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 402 #endif 403 404 /* 405 * BAT4 32M Cache-inhibited, guarded 406 * 0xe200_0000 16M PCI-Express 1 I/O 407 * 0xe300_0000 16M PCI-Express 2 I/0 408 * Note that this is at 0xe0000000 409 */ 410 #define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW \ 411 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 412 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP) 413 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 414 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 415 416 /* 417 * BAT5 128K Cacheable, non-guarded 418 * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) 419 */ 420 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 421 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 422 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 423 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 424 425 /* 426 * BAT6 32M Cache-inhibited, guarded 427 * 0xfe00_0000 32M FLASH 428 */ 429 #define CONFIG_SYS_DBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ 430 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 431 #define CONFIG_SYS_DBAT6U ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) 432 #define CONFIG_SYS_IBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) 433 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 434 435 /* Map the last 1M of flash where we're running from reset */ 436 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 437 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 438 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 439 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 440 | BATL_MEMCOHERENCE) 441 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 442 443 #define CONFIG_SYS_DBAT7L 0x00000000 444 #define CONFIG_SYS_DBAT7U 0x00000000 445 #define CONFIG_SYS_IBAT7L 0x00000000 446 #define CONFIG_SYS_IBAT7U 0x00000000 447 448 /* 449 * Environment 450 */ 451 #define CONFIG_ENV_IS_IN_FLASH 1 452 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 453 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k(one sector) for env */ 454 #define CONFIG_ENV_SIZE 0x2000 455 456 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 457 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 458 459 #define CONFIG_CMD_REGINFO 460 461 #if defined(CONFIG_PCI) 462 #define CONFIG_CMD_PCI 463 #endif 464 465 #undef CONFIG_WATCHDOG /* watchdog disabled */ 466 467 /* 468 * Miscellaneous configurable options 469 */ 470 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 471 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 472 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 473 474 #if defined(CONFIG_CMD_KGDB) 475 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 476 #else 477 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 478 #endif 479 480 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 481 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 482 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 483 484 /* 485 * For booting Linux, the board info and command line data 486 * have to be in the first 8 MB of memory, since this is 487 * the maximum mapped by the Linux kernel during initialization. 488 */ 489 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ 490 491 /* Cache Configuration */ 492 #define CONFIG_SYS_DCACHE_SIZE 32768 493 #define CONFIG_SYS_CACHELINE_SIZE 32 494 #if defined(CONFIG_CMD_KGDB) 495 #define CONFIG_SYS_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ 496 #endif 497 498 #if defined(CONFIG_CMD_KGDB) 499 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 500 #endif 501 502 /* 503 * Environment Configuration 504 */ 505 506 #define CONFIG_HAS_ETH0 1 507 #define CONFIG_HAS_ETH1 1 508 #define CONFIG_HAS_ETH2 1 509 #define CONFIG_HAS_ETH3 1 510 511 #define CONFIG_IPADDR 192.168.0.50 512 513 #define CONFIG_HOSTNAME sbc8641d 514 #define CONFIG_ROOTPATH "/opt/eldk/ppc_74xx" 515 #define CONFIG_BOOTFILE "uImage" 516 517 #define CONFIG_SERVERIP 192.168.0.2 518 #define CONFIG_GATEWAYIP 192.168.0.1 519 #define CONFIG_NETMASK 255.255.255.0 520 521 /* default location for tftp and bootm */ 522 #define CONFIG_LOADADDR 1000000 523 524 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 525 526 #define CONFIG_BAUDRATE 115200 527 528 #define CONFIG_EXTRA_ENV_SETTINGS \ 529 "netdev=eth0\0" \ 530 "consoledev=ttyS0\0" \ 531 "ramdiskaddr=2000000\0" \ 532 "ramdiskfile=uRamdisk\0" \ 533 "dtbaddr=400000\0" \ 534 "dtbfile=sbc8641d.dtb\0" \ 535 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ 536 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ 537 "maxcpus=1" 538 539 #define CONFIG_NFSBOOTCOMMAND \ 540 "setenv bootargs root=/dev/nfs rw " \ 541 "nfsroot=$serverip:$rootpath " \ 542 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 543 "console=$consoledev,$baudrate $othbootargs;" \ 544 "tftp $loadaddr $bootfile;" \ 545 "tftp $dtbaddr $dtbfile;" \ 546 "bootm $loadaddr - $dtbaddr" 547 548 #define CONFIG_RAMBOOTCOMMAND \ 549 "setenv bootargs root=/dev/ram rw " \ 550 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 551 "console=$consoledev,$baudrate $othbootargs;" \ 552 "tftp $ramdiskaddr $ramdiskfile;" \ 553 "tftp $loadaddr $bootfile;" \ 554 "tftp $dtbaddr $dtbfile;" \ 555 "bootm $loadaddr $ramdiskaddr $dtbaddr" 556 557 #define CONFIG_FLASHBOOTCOMMAND \ 558 "setenv bootargs root=/dev/ram rw " \ 559 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 560 "console=$consoledev,$baudrate $othbootargs;" \ 561 "bootm ffd00000 ffb00000 ffa00000" 562 563 #define CONFIG_BOOTCOMMAND CONFIG_FLASHBOOTCOMMAND 564 565 #endif /* __CONFIG_H */ 566