1 /* 2 * Copyright 2007 Wind River Systems <www.windriver.com> 3 * Copyright 2007 Embedded Specialties, Inc. 4 * Joe Hamman <joe.hamman@embeddedspecialties.com> 5 * 6 * Copyright 2006 Freescale Semiconductor. 7 * 8 * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 /* 14 * SBC8641D board configuration file 15 * 16 * Make sure you change the MAC address and other network params first, 17 * search for CONFIG_SERVERIP, etc in this file. 18 */ 19 20 #ifndef __CONFIG_H 21 #define __CONFIG_H 22 23 /* High Level Configuration Options */ 24 #define CONFIG_MPC8641 1 /* MPC8641 specific */ 25 #define CONFIG_SBC8641D 1 /* SBC8641D board specific */ 26 #define CONFIG_MP 1 /* support multiple processors */ 27 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 28 29 #define CONFIG_SYS_TEXT_BASE 0xfff00000 30 31 #ifdef RUN_DIAG 32 #define CONFIG_SYS_DIAG_ADDR 0xff800000 33 #endif 34 35 #define CONFIG_SYS_RESET_ADDRESS 0xfff00100 36 37 /* 38 * virtual address to be used for temporary mappings. There 39 * should be 128k free at this VA. 40 */ 41 #define CONFIG_SYS_SCRATCH_VA 0xe8000000 42 43 #define CONFIG_SYS_SRIO 44 #define CONFIG_SRIO1 /* SRIO port 1 */ 45 46 #define CONFIG_PCI 1 /* Enable PCIE */ 47 #define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ 48 #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ 49 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 50 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 51 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 52 53 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 54 #define CONFIG_ENV_OVERWRITE 55 56 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 57 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 58 59 #undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/ 60 #undef CONFIG_DDR_ECC /* only for ECC DDR module */ 61 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 62 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 63 #define CONFIG_NUM_DDR_CONTROLLERS 2 64 #define CACHE_LINE_INTERLEAVING 0x20000000 65 #define PAGE_INTERLEAVING 0x21000000 66 #define BANK_INTERLEAVING 0x22000000 67 #define SUPER_BANK_INTERLEAVING 0x23000000 68 69 70 #define CONFIG_ALTIVEC 1 71 72 /* 73 * L2CR setup -- make sure this is right for your board! 74 */ 75 #define CONFIG_SYS_L2 76 #define L2_INIT 0 77 #define L2_ENABLE (L2CR_L2E) 78 79 #ifndef CONFIG_SYS_CLK_FREQ 80 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 81 #endif 82 83 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 84 85 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 86 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 87 #define CONFIG_SYS_MEMTEST_END 0x00400000 88 89 /* 90 * Base addresses -- Note these are effective addresses where the 91 * actual resources get mapped (not physical addresses) 92 */ 93 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 94 #define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ 95 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 96 97 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 98 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 99 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW 100 101 /* 102 * DDR Setup 103 */ 104 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ 105 #define CONFIG_SYS_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */ 106 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 107 #define CONFIG_SYS_SDRAM_BASE2 CONFIG_SYS_DDR_SDRAM_BASE2 108 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 109 #define CONFIG_VERY_BIG_RAM 110 111 #define CONFIG_NUM_DDR_CONTROLLERS 2 112 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 113 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 114 115 #if defined(CONFIG_SPD_EEPROM) 116 /* 117 * Determine DDR configuration from I2C interface. 118 */ 119 #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */ 120 #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */ 121 #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */ 122 #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */ 123 124 #else 125 /* 126 * Manually set up DDR1 & DDR2 parameters 127 */ 128 129 #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ 130 131 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 132 #define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 133 #define CONFIG_SYS_DDR_CS2_BNDS 0x00000000 134 #define CONFIG_SYS_DDR_CS3_BNDS 0x00000000 135 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 136 #define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 137 #define CONFIG_SYS_DDR_CS2_CONFIG 0x00000000 138 #define CONFIG_SYS_DDR_CS3_CONFIG 0x00000000 139 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 140 #define CONFIG_SYS_DDR_TIMING_0 0x00220802 141 #define CONFIG_SYS_DDR_TIMING_1 0x38377322 142 #define CONFIG_SYS_DDR_TIMING_2 0x002040c7 143 #define CONFIG_SYS_DDR_CFG_1A 0x43008008 144 #define CONFIG_SYS_DDR_CFG_2 0x24401000 145 #define CONFIG_SYS_DDR_MODE_1 0x23c00542 146 #define CONFIG_SYS_DDR_MODE_2 0x00000000 147 #define CONFIG_SYS_DDR_MODE_CTL 0x00000000 148 #define CONFIG_SYS_DDR_INTERVAL 0x05080100 149 #define CONFIG_SYS_DDR_DATA_INIT 0x00000000 150 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 151 #define CONFIG_SYS_DDR_CFG_1B 0xC3008008 152 153 #define CONFIG_SYS_DDR2_CS0_BNDS 0x0010001F 154 #define CONFIG_SYS_DDR2_CS1_BNDS 0x00000000 155 #define CONFIG_SYS_DDR2_CS2_BNDS 0x00000000 156 #define CONFIG_SYS_DDR2_CS3_BNDS 0x00000000 157 #define CONFIG_SYS_DDR2_CS0_CONFIG 0x80010102 158 #define CONFIG_SYS_DDR2_CS1_CONFIG 0x00000000 159 #define CONFIG_SYS_DDR2_CS2_CONFIG 0x00000000 160 #define CONFIG_SYS_DDR2_CS3_CONFIG 0x00000000 161 #define CONFIG_SYS_DDR2_EXT_REFRESH 0x00000000 162 #define CONFIG_SYS_DDR2_TIMING_0 0x00220802 163 #define CONFIG_SYS_DDR2_TIMING_1 0x38377322 164 #define CONFIG_SYS_DDR2_TIMING_2 0x002040c7 165 #define CONFIG_SYS_DDR2_CFG_1A 0x43008008 166 #define CONFIG_SYS_DDR2_CFG_2 0x24401000 167 #define CONFIG_SYS_DDR2_MODE_1 0x23c00542 168 #define CONFIG_SYS_DDR2_MODE_2 0x00000000 169 #define CONFIG_SYS_DDR2_MODE_CTL 0x00000000 170 #define CONFIG_SYS_DDR2_INTERVAL 0x05080100 171 #define CONFIG_SYS_DDR2_DATA_INIT 0x00000000 172 #define CONFIG_SYS_DDR2_CLK_CTRL 0x03800000 173 #define CONFIG_SYS_DDR2_CFG_1B 0xC3008008 174 175 176 #endif 177 178 /* #define CONFIG_ID_EEPROM 1 179 #define ID_EEPROM_ADDR 0x57 */ 180 181 /* 182 * The SBC8641D contains 16MB flash space at ff000000. 183 */ 184 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ 185 186 /* Flash */ 187 #define CONFIG_SYS_BR0_PRELIM 0xff001001 /* port size 16bit */ 188 #define CONFIG_SYS_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */ 189 190 /* 64KB EEPROM */ 191 #define CONFIG_SYS_BR1_PRELIM 0xf0000801 /* port size 16bit */ 192 #define CONFIG_SYS_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */ 193 194 /* EPLD - User switches, board id, LEDs */ 195 #define CONFIG_SYS_BR2_PRELIM 0xf1000801 /* port size 16bit */ 196 #define CONFIG_SYS_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */ 197 198 /* Local bus SDRAM 128MB */ 199 #define CONFIG_SYS_BR3_PRELIM 0xe0001861 /* port size ?bit */ 200 #define CONFIG_SYS_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */ 201 #define CONFIG_SYS_BR4_PRELIM 0xe4001861 /* port size ?bit */ 202 #define CONFIG_SYS_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */ 203 204 /* Disk on Chip (DOC) 128MB */ 205 #define CONFIG_SYS_BR5_PRELIM 0xe8001001 /* port size ?bit */ 206 #define CONFIG_SYS_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */ 207 208 /* LCD */ 209 #define CONFIG_SYS_BR6_PRELIM 0xf4000801 /* port size ?bit */ 210 #define CONFIG_SYS_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ 211 212 /* Control logic & misc peripherals */ 213 #define CONFIG_SYS_BR7_PRELIM 0xf2000801 /* port size ?bit */ 214 #define CONFIG_SYS_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ 215 216 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 217 #define CONFIG_SYS_MAX_FLASH_SECT 131 /* sectors per device */ 218 219 #undef CONFIG_SYS_FLASH_CHECKSUM 220 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 221 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 222 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 223 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 224 225 #define CONFIG_FLASH_CFI_DRIVER 226 #define CONFIG_SYS_FLASH_CFI 227 #define CONFIG_SYS_WRITE_SWAPPED_DATA 228 #define CONFIG_SYS_FLASH_EMPTY_INFO 229 #define CONFIG_SYS_FLASH_PROTECTION 230 231 #undef CONFIG_CLOCKS_IN_MHZ 232 233 #define CONFIG_SYS_INIT_RAM_LOCK 1 234 #ifndef CONFIG_SYS_INIT_RAM_LOCK 235 #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ 236 #else 237 #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ 238 #endif 239 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 240 241 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 242 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 243 244 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 245 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 246 247 /* Serial Port */ 248 #define CONFIG_CONS_INDEX 1 249 #define CONFIG_SYS_NS16550 250 #define CONFIG_SYS_NS16550_SERIAL 251 #define CONFIG_SYS_NS16550_REG_SIZE 1 252 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 253 254 #define CONFIG_SYS_BAUDRATE_TABLE \ 255 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 256 257 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 258 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 259 260 /* Use the HUSH parser */ 261 #define CONFIG_SYS_HUSH_PARSER 262 #ifdef CONFIG_SYS_HUSH_PARSER 263 #endif 264 265 /* 266 * Pass open firmware flat tree to kernel 267 */ 268 #define CONFIG_OF_LIBFDT 1 269 #define CONFIG_OF_BOARD_SETUP 1 270 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 271 272 /* 273 * I2C 274 */ 275 #define CONFIG_SYS_I2C 276 #define CONFIG_SYS_I2C_FSL 277 #define CONFIG_SYS_FSL_I2C_SPEED 400000 278 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 279 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 280 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 281 282 /* 283 * RapidIO MMU 284 */ 285 #define CONFIG_SYS_SRIO1_MEM_BASE 0xc0000000 /* base address */ 286 #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BASE 287 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ 288 289 /* 290 * General PCI 291 * Addresses are mapped 1-1. 292 */ 293 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 294 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 295 #define CONFIG_SYS_PCIE1_MEM_VIRT CONFIG_SYS_PCIE1_MEM_BUS 296 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 297 #define CONFIG_SYS_PCIE1_IO_BUS 0xe2000000 298 #define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BUS 299 #define CONFIG_SYS_PCIE1_IO_VIRT CONFIG_SYS_PCIE1_IO_BUS 300 #define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */ 301 302 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 303 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 304 #define CONFIG_SYS_PCIE2_MEM_VIRT CONFIG_SYS_PCIE2_MEM_BUS 305 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 306 #define CONFIG_SYS_PCIE2_IO_BUS 0xe3000000 307 #define CONFIG_SYS_PCIE2_IO_PHYS CONFIG_SYS_PCIE2_IO_BUS 308 #define CONFIG_SYS_PCIE2_IO_VIRT CONFIG_SYS_PCIE2_IO_BUS 309 #define CONFIG_SYS_PCIE2_IO_SIZE 0x1000000 /* 16M */ 310 311 #if defined(CONFIG_PCI) 312 313 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 314 315 #undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE 316 317 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 318 319 #undef CONFIG_EEPRO100 320 #undef CONFIG_TULIP 321 322 #if !defined(CONFIG_PCI_PNP) 323 #define PCI_ENET0_IOADDR 0xe0000000 324 #define PCI_ENET0_MEMADDR 0xe0000000 325 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 326 #endif 327 328 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 329 330 #define CONFIG_DOS_PARTITION 331 #undef CONFIG_SCSI_AHCI 332 333 #ifdef CONFIG_SCSI_AHCI 334 #define CONFIG_SATA_ULI5288 335 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 336 #define CONFIG_SYS_SCSI_MAX_LUN 1 337 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 338 #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE 339 #endif 340 341 #endif /* CONFIG_PCI */ 342 343 #if defined(CONFIG_TSEC_ENET) 344 345 /* #define CONFIG_MII 1 */ /* MII PHY management */ 346 347 #define CONFIG_TSEC1 1 348 #define CONFIG_TSEC1_NAME "eTSEC1" 349 #define CONFIG_TSEC2 1 350 #define CONFIG_TSEC2_NAME "eTSEC2" 351 #define CONFIG_TSEC3 1 352 #define CONFIG_TSEC3_NAME "eTSEC3" 353 #define CONFIG_TSEC4 1 354 #define CONFIG_TSEC4_NAME "eTSEC4" 355 356 #define TSEC1_PHY_ADDR 0x1F 357 #define TSEC2_PHY_ADDR 0x00 358 #define TSEC3_PHY_ADDR 0x01 359 #define TSEC4_PHY_ADDR 0x02 360 #define TSEC1_PHYIDX 0 361 #define TSEC2_PHYIDX 0 362 #define TSEC3_PHYIDX 0 363 #define TSEC4_PHYIDX 0 364 #define TSEC1_FLAGS TSEC_GIGABIT 365 #define TSEC2_FLAGS TSEC_GIGABIT 366 #define TSEC3_FLAGS TSEC_GIGABIT 367 #define TSEC4_FLAGS TSEC_GIGABIT 368 369 #define CONFIG_SYS_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */ 370 371 #define CONFIG_ETHPRIME "eTSEC1" 372 373 #endif /* CONFIG_TSEC_ENET */ 374 375 /* 376 * BAT0 2G Cacheable, non-guarded 377 * 0x0000_0000 2G DDR 378 */ 379 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 380 #define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) 381 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) 382 #define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U 383 384 /* 385 * BAT1 1G Cache-inhibited, guarded 386 * 0x8000_0000 512M PCI-Express 1 Memory 387 * 0xa000_0000 512M PCI-Express 2 Memory 388 * Changed it for operating from 0xd0000000 389 */ 390 #define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW \ 391 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 392 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP) 393 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 394 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 395 396 /* 397 * BAT2 512M Cache-inhibited, guarded 398 * 0xc000_0000 512M RapidIO Memory 399 */ 400 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_SRIO1_MEM_BASE | BATL_PP_RW \ 401 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 402 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP) 403 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_SRIO1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) 404 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 405 406 /* 407 * BAT3 4M Cache-inhibited, guarded 408 * 0xf800_0000 4M CCSR 409 */ 410 #define CONFIG_SYS_DBAT3L ( CONFIG_SYS_CCSRBAR | BATL_PP_RW \ 411 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 412 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) 413 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) 414 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 415 416 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 417 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 418 | BATL_PP_RW | BATL_CACHEINHIBIT \ 419 | BATL_GUARDEDSTORAGE) 420 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 421 | BATU_BL_1M | BATU_VS | BATU_VP) 422 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 423 | BATL_PP_RW | BATL_CACHEINHIBIT) 424 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 425 #endif 426 427 /* 428 * BAT4 32M Cache-inhibited, guarded 429 * 0xe200_0000 16M PCI-Express 1 I/O 430 * 0xe300_0000 16M PCI-Express 2 I/0 431 * Note that this is at 0xe0000000 432 */ 433 #define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW \ 434 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 435 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP) 436 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 437 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 438 439 /* 440 * BAT5 128K Cacheable, non-guarded 441 * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) 442 */ 443 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 444 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 445 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 446 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 447 448 /* 449 * BAT6 32M Cache-inhibited, guarded 450 * 0xfe00_0000 32M FLASH 451 */ 452 #define CONFIG_SYS_DBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ 453 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 454 #define CONFIG_SYS_DBAT6U ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) 455 #define CONFIG_SYS_IBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) 456 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 457 458 /* Map the last 1M of flash where we're running from reset */ 459 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 460 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 461 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 462 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 463 | BATL_MEMCOHERENCE) 464 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 465 466 #define CONFIG_SYS_DBAT7L 0x00000000 467 #define CONFIG_SYS_DBAT7U 0x00000000 468 #define CONFIG_SYS_IBAT7L 0x00000000 469 #define CONFIG_SYS_IBAT7U 0x00000000 470 471 /* 472 * Environment 473 */ 474 #define CONFIG_ENV_IS_IN_FLASH 1 475 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 476 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 477 #define CONFIG_ENV_SIZE 0x2000 478 479 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 480 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 481 482 #define CONFIG_CMD_PING 483 #define CONFIG_CMD_I2C 484 #define CONFIG_CMD_REGINFO 485 486 #if defined(CONFIG_PCI) 487 #define CONFIG_CMD_PCI 488 #endif 489 490 #undef CONFIG_WATCHDOG /* watchdog disabled */ 491 492 /* 493 * Miscellaneous configurable options 494 */ 495 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 496 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 497 498 #if defined(CONFIG_CMD_KGDB) 499 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 500 #else 501 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 502 #endif 503 504 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 505 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 506 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 507 508 /* 509 * For booting Linux, the board info and command line data 510 * have to be in the first 8 MB of memory, since this is 511 * the maximum mapped by the Linux kernel during initialization. 512 */ 513 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ 514 515 /* Cache Configuration */ 516 #define CONFIG_SYS_DCACHE_SIZE 32768 517 #define CONFIG_SYS_CACHELINE_SIZE 32 518 #if defined(CONFIG_CMD_KGDB) 519 #define CONFIG_SYS_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ 520 #endif 521 522 #if defined(CONFIG_CMD_KGDB) 523 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 524 #endif 525 526 /* 527 * Environment Configuration 528 */ 529 530 #define CONFIG_HAS_ETH0 1 531 #define CONFIG_HAS_ETH1 1 532 #define CONFIG_HAS_ETH2 1 533 #define CONFIG_HAS_ETH3 1 534 535 #define CONFIG_IPADDR 192.168.0.50 536 537 #define CONFIG_HOSTNAME sbc8641d 538 #define CONFIG_ROOTPATH "/opt/eldk/ppc_74xx" 539 #define CONFIG_BOOTFILE "uImage" 540 541 #define CONFIG_SERVERIP 192.168.0.2 542 #define CONFIG_GATEWAYIP 192.168.0.1 543 #define CONFIG_NETMASK 255.255.255.0 544 545 /* default location for tftp and bootm */ 546 #define CONFIG_LOADADDR 1000000 547 548 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 549 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 550 551 #define CONFIG_BAUDRATE 115200 552 553 #define CONFIG_EXTRA_ENV_SETTINGS \ 554 "netdev=eth0\0" \ 555 "consoledev=ttyS0\0" \ 556 "ramdiskaddr=2000000\0" \ 557 "ramdiskfile=uRamdisk\0" \ 558 "dtbaddr=400000\0" \ 559 "dtbfile=sbc8641d.dtb\0" \ 560 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ 561 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ 562 "maxcpus=1" 563 564 #define CONFIG_NFSBOOTCOMMAND \ 565 "setenv bootargs root=/dev/nfs rw " \ 566 "nfsroot=$serverip:$rootpath " \ 567 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 568 "console=$consoledev,$baudrate $othbootargs;" \ 569 "tftp $loadaddr $bootfile;" \ 570 "tftp $dtbaddr $dtbfile;" \ 571 "bootm $loadaddr - $dtbaddr" 572 573 #define CONFIG_RAMBOOTCOMMAND \ 574 "setenv bootargs root=/dev/ram rw " \ 575 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 576 "console=$consoledev,$baudrate $othbootargs;" \ 577 "tftp $ramdiskaddr $ramdiskfile;" \ 578 "tftp $loadaddr $bootfile;" \ 579 "tftp $dtbaddr $dtbfile;" \ 580 "bootm $loadaddr $ramdiskaddr $dtbaddr" 581 582 #define CONFIG_FLASHBOOTCOMMAND \ 583 "setenv bootargs root=/dev/ram rw " \ 584 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 585 "console=$consoledev,$baudrate $othbootargs;" \ 586 "bootm ffd00000 ffb00000 ffa00000" 587 588 #define CONFIG_BOOTCOMMAND CONFIG_FLASHBOOTCOMMAND 589 590 #endif /* __CONFIG_H */ 591