1 /* 2 * Configuration settings for the SAMA5D4 Xplained ultra board. 3 * 4 * Copyright (C) 2014 Atmel 5 * Bo Shen <voice.shen@atmel.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* No NOR flash, this definition should put before common header */ 14 #define CONFIG_SYS_NO_FLASH 15 16 #include "at91-sama5_common.h" 17 18 /* serial console */ 19 #define CONFIG_ATMEL_USART 20 #define CONFIG_USART_BASE ATMEL_BASE_USART3 21 #define CONFIG_USART_ID ATMEL_ID_USART3 22 23 /* SDRAM */ 24 #define CONFIG_NR_DRAM_BANKS 1 25 #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS 26 #define CONFIG_SYS_SDRAM_SIZE 0x20000000 27 28 #ifdef CONFIG_SPL_BUILD 29 #define CONFIG_SYS_INIT_SP_ADDR 0x210000 30 #else 31 #define CONFIG_SYS_INIT_SP_ADDR \ 32 (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) 33 #endif 34 35 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 36 37 /* SerialFlash */ 38 #define CONFIG_CMD_SF 39 40 #ifdef CONFIG_CMD_SF 41 #define CONFIG_ATMEL_SPI 42 #define CONFIG_ATMEL_SPI0 43 #define CONFIG_SPI_FLASH 44 #define CONFIG_SPI_FLASH_ATMEL 45 #define CONFIG_SF_DEFAULT_BUS 0 46 #define CONFIG_SF_DEFAULT_CS 0 47 #define CONFIG_SF_DEFAULT_SPEED 30000000 48 #endif 49 50 /* NAND flash */ 51 #define CONFIG_CMD_NAND 52 53 #ifdef CONFIG_CMD_NAND 54 #define CONFIG_NAND_ATMEL 55 #define CONFIG_SYS_MAX_NAND_DEVICE 1 56 #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 57 /* our ALE is AD21 */ 58 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 59 /* our CLE is AD22 */ 60 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 61 #define CONFIG_SYS_NAND_ONFI_DETECTION 62 /* PMECC & PMERRLOC */ 63 #define CONFIG_ATMEL_NAND_HWECC 64 #define CONFIG_ATMEL_NAND_HW_PMECC 65 #endif 66 67 /* MMC */ 68 #define CONFIG_CMD_MMC 69 70 #ifdef CONFIG_CMD_MMC 71 #define CONFIG_MMC 72 #define CONFIG_GENERIC_MMC 73 #define CONFIG_GENERIC_ATMEL_MCI 74 #define ATMEL_BASE_MMCI ATMEL_BASE_MCI1 75 #endif 76 77 /* USB */ 78 #define CONFIG_CMD_USB 79 80 #ifdef CONFIG_CMD_USB 81 #define CONFIG_USB_EHCI 82 #define CONFIG_USB_EHCI_ATMEL 83 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 84 #define CONFIG_USB_STORAGE 85 #endif 86 87 /* USB device */ 88 #define CONFIG_USB_GADGET 89 #define CONFIG_USB_GADGET_DUALSPEED 90 #define CONFIG_USB_GADGET_ATMEL_USBA 91 #define CONFIG_USB_ETHER 92 #define CONFIG_USB_ETH_RNDIS 93 #define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK" 94 95 #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) 96 #define CONFIG_CMD_FAT 97 #define CONFIG_DOS_PARTITION 98 #endif 99 100 /* Ethernet Hardware */ 101 #define CONFIG_MACB 102 #define CONFIG_RMII 103 #define CONFIG_NET_RETRY_COUNT 20 104 #define CONFIG_MACB_SEARCH_PHY 105 106 /* LCD */ 107 /* #define CONFIG_LCD */ 108 #ifdef CONFIG_LCD 109 #define LCD_BPP LCD_COLOR16 110 #define LCD_OUTPUT_BPP 24 111 #define CONFIG_LCD_LOGO 112 #define CONFIG_LCD_INFO 113 #define CONFIG_LCD_INFO_BELOW_LOGO 114 #define CONFIG_SYS_WHITE_ON_BLACK 115 #define CONFIG_ATMEL_HLCD 116 #define CONFIG_ATMEL_LCD_RGB565 117 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 118 #endif 119 120 #ifdef CONFIG_SYS_USE_SERIALFLASH 121 /* bootstrap + u-boot + env + linux in serial flash */ 122 #define CONFIG_ENV_IS_IN_SPI_FLASH 123 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS 124 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 125 #define CONFIG_ENV_OFFSET 0x10000 126 #define CONFIG_ENV_SIZE 0x10000 127 #define CONFIG_ENV_SECT_SIZE 0x1000 128 #define CONFIG_BOOTCOMMAND "sf probe 0; " \ 129 "sf read 0x21000000 0xa0000 0x60000; " \ 130 "sf read 0x22000000 0x100000 0x300000; " \ 131 "bootz 0x22000000 - 0x21000000" 132 #elif CONFIG_SYS_USE_NANDFLASH 133 /* bootstrap + u-boot + env in nandflash */ 134 #define CONFIG_ENV_IS_IN_NAND 135 #define CONFIG_ENV_OFFSET 0xc0000 136 #define CONFIG_ENV_OFFSET_REDUND 0x100000 137 #define CONFIG_ENV_SIZE 0x20000 138 #define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \ 139 "nand read 0x22000000 0x200000 0x600000;" \ 140 "bootz 0x22000000 - 0x21000000" 141 #elif CONFIG_SYS_USE_MMC 142 /* bootstrap + u-boot + env in sd card */ 143 #define CONFIG_ENV_IS_IN_FAT 144 #define CONFIG_FAT_WRITE 145 #define FAT_ENV_INTERFACE "mmc" 146 /* 147 * We don't specify the part number, if device 0 has partition table, it means 148 * the first partition; it no partition table, then take whole device as a 149 * FAT file system. 150 */ 151 #define FAT_ENV_DEVICE_AND_PART "0" 152 #define FAT_ENV_FILE "uboot.env" 153 #define CONFIG_ENV_SIZE 0x4000 154 #define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d4_xplained.dtb; " \ 155 "fatload mmc 0:1 0x22000000 zImage; " \ 156 "bootz 0x22000000 - 0x21000000" 157 #endif 158 159 160 161 /* SPL */ 162 #define CONFIG_SPL_FRAMEWORK 163 #define CONFIG_SPL_TEXT_BASE 0x200000 164 #define CONFIG_SPL_MAX_SIZE 0x10000 165 #define CONFIG_SPL_BSS_START_ADDR 0x20000000 166 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 167 #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 168 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 169 170 #define CONFIG_SPL_LIBCOMMON_SUPPORT 171 #define CONFIG_SPL_LIBGENERIC_SUPPORT 172 #define CONFIG_SPL_GPIO_SUPPORT 173 #define CONFIG_SPL_SERIAL_SUPPORT 174 175 #define CONFIG_SPL_BOARD_INIT 176 #define CONFIG_SYS_MONITOR_LEN (512 << 10) 177 178 #ifdef CONFIG_SYS_USE_MMC 179 #define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds 180 #define CONFIG_SPL_MMC_SUPPORT 181 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 182 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 183 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 184 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 185 #define CONFIG_SPL_FAT_SUPPORT 186 #define CONFIG_SPL_LIBDISK_SUPPORT 187 188 #elif CONFIG_SYS_USE_NANDFLASH 189 #define CONFIG_SPL_NAND_SUPPORT 190 #define CONFIG_SPL_NAND_DRIVERS 191 #define CONFIG_SPL_NAND_BASE 192 #define CONFIG_PMECC_CAP 8 193 #define CONFIG_PMECC_SECTOR_SIZE 512 194 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 195 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 196 #define CONFIG_SYS_NAND_PAGE_SIZE 0x1000 197 #define CONFIG_SYS_NAND_PAGE_COUNT 64 198 #define CONFIG_SYS_NAND_OOBSIZE 224 199 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000 200 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 201 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER 202 203 #elif CONFIG_SYS_USE_SERIALFLASH 204 #define CONFIG_SPL_SPI_SUPPORT 205 #define CONFIG_SPL_SPI_FLASH_SUPPORT 206 #define CONFIG_SPL_SPI_LOAD 207 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 208 209 #endif 210 #endif 211