1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Configuation settings for the SAMA5D3xEK board. 4 * 5 * Copyright (C) 2012 - 2013 Atmel 6 * 7 * based on at91sam9m10g45ek.h by: 8 * Stelian Pop <stelian@popies.net> 9 * Lead Tech Design <www.leadtechdesign.com> 10 */ 11 12 #ifndef __CONFIG_H 13 #define __CONFIG_H 14 15 #include "at91-sama5_common.h" 16 17 /* 18 * This needs to be defined for the OHCI code to work but it is defined as 19 * ATMEL_ID_UHPHS in the CPU specific header files. 20 */ 21 #define ATMEL_ID_UHP 32 22 23 /* 24 * Specify the clock enable bit in the PMC_SCER register. 25 */ 26 #define ATMEL_PMC_UHP (1 << 6) 27 28 /* board specific (not enough SRAM) */ 29 #define CONFIG_SAMA5D3_LCD_BASE 0x23E00000 30 31 /* NOR flash */ 32 #ifdef CONFIG_MTD_NOR_FLASH 33 #define CONFIG_FLASH_CFI_DRIVER 34 #define CONFIG_SYS_FLASH_CFI 35 #define CONFIG_SYS_FLASH_PROTECTION 36 #define CONFIG_SYS_FLASH_BASE 0x10000000 37 #define CONFIG_SYS_MAX_FLASH_SECT 131 38 #define CONFIG_SYS_MAX_FLASH_BANKS 1 39 #endif 40 41 /* SDRAM */ 42 #define CONFIG_SYS_SDRAM_BASE 0x20000000 43 #define CONFIG_SYS_SDRAM_SIZE 0x20000000 44 45 #ifdef CONFIG_SPL_BUILD 46 #define CONFIG_SYS_INIT_SP_ADDR 0x318000 47 #else 48 #define CONFIG_SYS_INIT_SP_ADDR \ 49 (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) 50 #endif 51 52 /* SerialFlash */ 53 54 #ifdef CONFIG_CMD_SF 55 #define CONFIG_SF_DEFAULT_SPEED 30000000 56 #endif 57 58 /* NAND flash */ 59 #ifdef CONFIG_CMD_NAND 60 #define CONFIG_SYS_MAX_NAND_DEVICE 1 61 #define CONFIG_SYS_NAND_BASE 0x60000000 62 /* our ALE is AD21 */ 63 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 64 /* our CLE is AD22 */ 65 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 66 #define CONFIG_SYS_NAND_ONFI_DETECTION 67 #endif 68 /* PMECC & PMERRLOC */ 69 #define CONFIG_ATMEL_NAND_HWECC 70 #define CONFIG_ATMEL_NAND_HW_PMECC 71 #define CONFIG_PMECC_CAP 4 72 #define CONFIG_PMECC_SECTOR_SIZE 512 73 74 /* USB */ 75 76 #ifdef CONFIG_CMD_USB 77 #define CONFIG_USB_ATMEL_CLK_SEL_UPLL 78 #define CONFIG_USB_OHCI_NEW 79 #define CONFIG_SYS_USB_OHCI_CPU_INIT 80 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI 81 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "sama5d3" 82 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3 83 #endif 84 85 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 86 87 /* SPL */ 88 #define CONFIG_SPL_TEXT_BASE 0x300000 89 #define CONFIG_SPL_MAX_SIZE 0x18000 90 #define CONFIG_SPL_BSS_START_ADDR 0x20000000 91 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 92 #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 93 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 94 95 #define CONFIG_SYS_MONITOR_LEN (512 << 10) 96 97 #ifdef CONFIG_SD_BOOT 98 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 99 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 100 101 #elif CONFIG_SPI_BOOT 102 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000 103 104 #elif CONFIG_NAND_BOOT 105 #define CONFIG_SPL_NAND_DRIVERS 106 #define CONFIG_SPL_NAND_BASE 107 #endif 108 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 109 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 110 #define CONFIG_SYS_NAND_PAGE_SIZE 0x800 111 #define CONFIG_SYS_NAND_PAGE_COUNT 64 112 #define CONFIG_SYS_NAND_OOBSIZE 64 113 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 114 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 115 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER 116 117 #endif 118