1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Configuration settings for the SAMA5D3 Xplained board. 4 * 5 * Copyright (C) 2014 Atmel Corporation 6 * Bo Shen <voice.shen@atmel.com> 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #include "at91-sama5_common.h" 13 14 /* 15 * This needs to be defined for the OHCI code to work but it is defined as 16 * ATMEL_ID_UHPHS in the CPU specific header files. 17 */ 18 #define ATMEL_ID_UHP 32 19 20 /* 21 * Specify the clock enable bit in the PMC_SCER register. 22 */ 23 #define ATMEL_PMC_UHP (1 << 6) 24 25 /* SDRAM */ 26 #define CONFIG_NR_DRAM_BANKS 1 27 #define CONFIG_SYS_SDRAM_BASE 0x20000000 28 #define CONFIG_SYS_SDRAM_SIZE 0x10000000 29 30 #ifdef CONFIG_SPL_BUILD 31 #define CONFIG_SYS_INIT_SP_ADDR 0x318000 32 #else 33 #define CONFIG_SYS_INIT_SP_ADDR \ 34 (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) 35 #endif 36 37 /* NAND flash */ 38 #ifdef CONFIG_CMD_NAND 39 #define CONFIG_NAND_ATMEL 40 #define CONFIG_SYS_MAX_NAND_DEVICE 1 41 #define CONFIG_SYS_NAND_BASE 0x60000000 42 /* our ALE is AD21 */ 43 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 44 /* our CLE is AD22 */ 45 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 46 #define CONFIG_SYS_NAND_ONFI_DETECTION 47 48 #define CONFIG_MTD_DEVICE 49 #define CONFIG_MTD_PARTITIONS 50 #endif 51 /* PMECC & PMERRLOC */ 52 #define CONFIG_ATMEL_NAND_HWECC 53 #define CONFIG_ATMEL_NAND_HW_PMECC 54 #define CONFIG_PMECC_CAP 4 55 #define CONFIG_PMECC_SECTOR_SIZE 512 56 57 /* USB */ 58 59 #ifdef CONFIG_CMD_USB 60 #define CONFIG_USB_ATMEL 61 #define CONFIG_USB_ATMEL_CLK_SEL_UPLL 62 #define CONFIG_USB_OHCI_NEW 63 #define CONFIG_SYS_USB_OHCI_CPU_INIT 64 #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00600000 65 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "SAMA5D3 Xplained" 66 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 67 #endif 68 69 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 70 71 /* SPL */ 72 #define CONFIG_SPL_TEXT_BASE 0x300000 73 #define CONFIG_SPL_MAX_SIZE 0x18000 74 #define CONFIG_SPL_BSS_START_ADDR 0x20000000 75 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 76 #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 77 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 78 79 #define CONFIG_SYS_MONITOR_LEN (512 << 10) 80 81 #ifdef CONFIG_SD_BOOT 82 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 83 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 84 85 #elif CONFIG_NAND_BOOT 86 #define CONFIG_SPL_NAND_DRIVERS 87 #define CONFIG_SPL_NAND_BASE 88 #endif 89 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 90 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 91 #define CONFIG_SYS_NAND_PAGE_SIZE 0x800 92 #define CONFIG_SYS_NAND_PAGE_COUNT 64 93 #define CONFIG_SYS_NAND_OOBSIZE 64 94 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 95 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 96 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER 97 98 #endif 99