1 /* 2 * Configuration settings for the SAMA5D3 Xplained board. 3 * 4 * Copyright (C) 2014 Atmel Corporation 5 * Bo Shen <voice.shen@atmel.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #include "at91-sama5_common.h" 14 15 /* 16 * This needs to be defined for the OHCI code to work but it is defined as 17 * ATMEL_ID_UHPHS in the CPU specific header files. 18 */ 19 #define ATMEL_ID_UHP 32 20 21 /* 22 * Specify the clock enable bit in the PMC_SCER register. 23 */ 24 #define ATMEL_PMC_UHP (1 << 6) 25 26 /* SDRAM */ 27 #define CONFIG_NR_DRAM_BANKS 1 28 #define CONFIG_SYS_SDRAM_BASE 0x20000000 29 #define CONFIG_SYS_SDRAM_SIZE 0x10000000 30 31 #ifdef CONFIG_SPL_BUILD 32 #define CONFIG_SYS_INIT_SP_ADDR 0x318000 33 #else 34 #define CONFIG_SYS_INIT_SP_ADDR \ 35 (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) 36 #endif 37 38 /* NAND flash */ 39 #ifdef CONFIG_CMD_NAND 40 #define CONFIG_NAND_ATMEL 41 #define CONFIG_SYS_MAX_NAND_DEVICE 1 42 #define CONFIG_SYS_NAND_BASE 0x60000000 43 /* our ALE is AD21 */ 44 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 45 /* our CLE is AD22 */ 46 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 47 #define CONFIG_SYS_NAND_ONFI_DETECTION 48 49 #define CONFIG_MTD_DEVICE 50 #define CONFIG_MTD_PARTITIONS 51 #endif 52 /* PMECC & PMERRLOC */ 53 #define CONFIG_ATMEL_NAND_HWECC 54 #define CONFIG_ATMEL_NAND_HW_PMECC 55 #define CONFIG_PMECC_CAP 4 56 #define CONFIG_PMECC_SECTOR_SIZE 512 57 58 /* USB */ 59 60 #ifdef CONFIG_CMD_USB 61 #define CONFIG_USB_ATMEL 62 #define CONFIG_USB_ATMEL_CLK_SEL_UPLL 63 #define CONFIG_USB_OHCI_NEW 64 #define CONFIG_SYS_USB_OHCI_CPU_INIT 65 #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00600000 66 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "SAMA5D3 Xplained" 67 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 68 #endif 69 70 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 71 72 /* SPL */ 73 #define CONFIG_SPL_TEXT_BASE 0x300000 74 #define CONFIG_SPL_MAX_SIZE 0x18000 75 #define CONFIG_SPL_BSS_START_ADDR 0x20000000 76 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 77 #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 78 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 79 80 #define CONFIG_SYS_MONITOR_LEN (512 << 10) 81 82 #ifdef CONFIG_SD_BOOT 83 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 84 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 85 86 #elif CONFIG_NAND_BOOT 87 #define CONFIG_SPL_NAND_DRIVERS 88 #define CONFIG_SPL_NAND_BASE 89 #endif 90 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 91 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 92 #define CONFIG_SYS_NAND_PAGE_SIZE 0x800 93 #define CONFIG_SYS_NAND_PAGE_COUNT 64 94 #define CONFIG_SYS_NAND_OOBSIZE 64 95 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 96 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 97 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER 98 99 #endif 100