1 /* 2 * Configuration settings for the SAMA5D3 Xplained board. 3 * 4 * Copyright (C) 2014 Atmel Corporation 5 * Bo Shen <voice.shen@atmel.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* No NOR flash, this definition should put before common header */ 14 #define CONFIG_SYS_NO_FLASH 15 16 #include "at91-sama5_common.h" 17 18 /* serial console */ 19 #define CONFIG_ATMEL_USART 20 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 21 #define CONFIG_USART_ID ATMEL_ID_DBGU 22 23 /* 24 * This needs to be defined for the OHCI code to work but it is defined as 25 * ATMEL_ID_UHPHS in the CPU specific header files. 26 */ 27 #define ATMEL_ID_UHP ATMEL_ID_UHPHS 28 29 /* 30 * Specify the clock enable bit in the PMC_SCER register. 31 */ 32 #define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP 33 34 /* SDRAM */ 35 #define CONFIG_NR_DRAM_BANKS 1 36 #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS 37 #define CONFIG_SYS_SDRAM_SIZE 0x10000000 38 39 #ifdef CONFIG_SPL_BUILD 40 #define CONFIG_SYS_INIT_SP_ADDR 0x310000 41 #else 42 #define CONFIG_SYS_INIT_SP_ADDR \ 43 (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) 44 #endif 45 46 /* NAND flash */ 47 #define CONFIG_CMD_NAND 48 49 #ifdef CONFIG_CMD_NAND 50 #define CONFIG_NAND_ATMEL 51 #define CONFIG_SYS_MAX_NAND_DEVICE 1 52 #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 53 /* our ALE is AD21 */ 54 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 55 /* our CLE is AD22 */ 56 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 57 #define CONFIG_SYS_NAND_ONFI_DETECTION 58 /* PMECC & PMERRLOC */ 59 #define CONFIG_ATMEL_NAND_HWECC 60 #define CONFIG_ATMEL_NAND_HW_PMECC 61 #define CONFIG_PMECC_CAP 4 62 #define CONFIG_PMECC_SECTOR_SIZE 512 63 #define CONFIG_CMD_NAND_TRIMFFS 64 #define CONFIG_CMD_MTDPARTS 65 66 #define CONFIG_MTD_DEVICE 67 #define CONFIG_MTD_PARTITIONS 68 #define CONFIG_RBTREE 69 #define CONFIG_LZO 70 #define CONFIG_CMD_UBI 71 #define CONFIG_CMD_UBIFS 72 #endif 73 74 /* Ethernet Hardware */ 75 #define CONFIG_MACB 76 #define CONFIG_RMII 77 #define CONFIG_NET_RETRY_COUNT 20 78 #define CONFIG_MACB_SEARCH_PHY 79 #define CONFIG_RGMII 80 #define CONFIG_CMD_MII 81 #define CONFIG_PHYLIB 82 83 /* MMC */ 84 #define CONFIG_CMD_MMC 85 86 #ifdef CONFIG_CMD_MMC 87 #define CONFIG_MMC 88 #define CONFIG_GENERIC_MMC 89 #define CONFIG_GENERIC_ATMEL_MCI 90 #define CONFIG_ATMEL_MCI_8BIT 91 #endif 92 93 /* USB */ 94 #define CONFIG_CMD_USB 95 96 #ifdef CONFIG_CMD_USB 97 #define CONFIG_USB_ATMEL 98 #define CONFIG_USB_ATMEL_CLK_SEL_UPLL 99 #define CONFIG_USB_OHCI_NEW 100 #define CONFIG_SYS_USB_OHCI_CPU_INIT 101 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI 102 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "SAMA5D3 Xplained" 103 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 104 #define CONFIG_DOS_PARTITION 105 #define CONFIG_USB_STORAGE 106 #endif 107 108 #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) 109 #define CONFIG_CMD_FAT 110 #define CONFIG_FAT_WRITE 111 #define CONFIG_CMD_EXT4 112 #define CONFIG_CMD_EXT4_WRITE 113 #endif 114 115 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 116 117 #if CONFIG_SYS_USE_NANDFLASH 118 /* bootstrap + u-boot + env in nandflash */ 119 #define CONFIG_ENV_IS_IN_NAND 120 #define CONFIG_ENV_OFFSET 0xc0000 121 #define CONFIG_ENV_OFFSET_REDUND 0x100000 122 #define CONFIG_ENV_SIZE 0x20000 123 #define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \ 124 "nand read 0x22000000 0x200000 0x600000;" \ 125 "bootz 0x22000000 - 0x21000000" 126 #elif CONFIG_SYS_USE_MMC 127 /* bootstrap + u-boot + env in sd card */ 128 #define CONFIG_ENV_IS_IN_FAT 129 #define FAT_ENV_INTERFACE "mmc" 130 #define FAT_ENV_FILE "uboot.env" 131 #define FAT_ENV_DEVICE_AND_PART "0" 132 #define CONFIG_ENV_SIZE 0x4000 133 #define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d3_xplained.dtb; " \ 134 "fatload mmc 0:1 0x22000000 zImage; " \ 135 "bootz 0x22000000 - 0x21000000" 136 #else 137 #define CONFIG_ENV_IS_NOWHERE 138 #endif 139 140 /* SPL */ 141 #define CONFIG_SPL_FRAMEWORK 142 #define CONFIG_SPL_TEXT_BASE 0x300000 143 #define CONFIG_SPL_MAX_SIZE 0x10000 144 #define CONFIG_SPL_BSS_START_ADDR 0x20000000 145 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 146 #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 147 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 148 149 #define CONFIG_SPL_LIBCOMMON_SUPPORT 150 #define CONFIG_SPL_LIBGENERIC_SUPPORT 151 #define CONFIG_SPL_GPIO_SUPPORT 152 #define CONFIG_SPL_SERIAL_SUPPORT 153 154 #define CONFIG_SPL_BOARD_INIT 155 #define CONFIG_SYS_MONITOR_LEN (512 << 10) 156 157 #ifdef CONFIG_SYS_USE_MMC 158 #define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds 159 #define CONFIG_SPL_MMC_SUPPORT 160 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 161 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 162 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 163 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 164 #define CONFIG_SPL_FAT_SUPPORT 165 #define CONFIG_SPL_LIBDISK_SUPPORT 166 167 #elif CONFIG_SYS_USE_NANDFLASH 168 #define CONFIG_SPL_NAND_SUPPORT 169 #define CONFIG_SPL_NAND_DRIVERS 170 #define CONFIG_SPL_NAND_BASE 171 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 172 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 173 #define CONFIG_SYS_NAND_PAGE_SIZE 0x800 174 #define CONFIG_SYS_NAND_PAGE_COUNT 64 175 #define CONFIG_SYS_NAND_OOBSIZE 64 176 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 177 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 178 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER 179 180 #endif 181 182 #endif 183