1 /* 2 * siemens rut 3 * (C) Copyright 2013 Siemens Schweiz AG 4 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * 6 * Based on: 7 * U-Boot file:/include/configs/am335x_evm.h 8 * 9 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14 #ifndef __CONFIG_RUT_H 15 #define __CONFIG_RUT_H 16 17 #define CONFIG_SIEMENS_RUT 18 #define MACH_TYPE_RUT 4316 19 #define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_RUT 20 21 #include "siemens-am33x-common.h" 22 23 #define CONFIG_SYS_MPUCLK 600 24 #define RUT_IOCTRL_VAL 0x18b 25 #define DDR_PLL_FREQ 303 26 27 /* Physical Memory Map */ 28 #define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MiB */ 29 30 /* I2C Configuration */ 31 #define CONFIG_SYS_I2C_SPEED 100000 32 33 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 34 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 35 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 36 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 37 38 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 39 40 #undef CONFIG_SPL_NET_SUPPORT 41 #undef CONFIG_SPL_NET_VCI_STRING 42 #undef CONFIG_SPL_ETH_SUPPORT 43 44 #define CONFIG_PHY_NATSEMI 45 46 #define CONFIG_FACTORYSET 47 48 49 /* Watchdog */ 50 #define WATCHDOG_TRIGGER_GPIO 14 51 52 #ifndef CONFIG_SPL_BUILD 53 54 /* Use common default */ 55 #define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V1 56 57 /* Default env settings */ 58 #define CONFIG_EXTRA_ENV_SETTINGS \ 59 "hostname=rut\0" \ 60 "nand_img_size=0x500000\0" \ 61 "splashpos=m,m\0" \ 62 "optargs=fixrtc --no-log consoleblank=0 \0" \ 63 CONFIG_ENV_SETTINGS_V1 \ 64 CONFIG_ENV_SETTINGS_NAND_V1 \ 65 "mmc_dev=0\0" \ 66 "mmc_root=/dev/mmcblk0p2 rw\0" \ 67 "mmc_root_fs_type=ext4 rootwait\0" \ 68 "mmc_load_uimage=" \ 69 "mmc rescan; " \ 70 "setenv bootfile uImage;" \ 71 "fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \ 72 "loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \ 73 "importbootenv=echo Importing environment from mmc ...; " \ 74 "env import -t $loadaddr $filesize\0" \ 75 "mmc_args=run bootargs_defaults;" \ 76 "mtdparts default;" \ 77 "setenv bootargs ${bootargs} " \ 78 "root=${mmc_root} ${mtdparts}" \ 79 "rootfstype=${mmc_root_fs_type} ip=${ip_method} " \ 80 "eth=${ethaddr} " \ 81 "\0" \ 82 "mmc_boot=run mmc_args; " \ 83 "run mmc_load_uimage; " \ 84 "bootm ${kloadaddr}\0" \ 85 "" 86 87 #ifndef CONFIG_RESTORE_FLASH 88 /* set to negative value for no autoboot */ 89 #define CONFIG_BOOTDELAY 3 90 91 #define CONFIG_BOOTCOMMAND \ 92 "if mmc rescan; then " \ 93 "echo SD/MMC found on device ${mmc_dev};" \ 94 "if run loadbootenv; then " \ 95 "echo Loaded environment from ${bootenv};" \ 96 "run importbootenv;" \ 97 "fi;" \ 98 "if test -n $uenvcmd; then " \ 99 "echo Running uenvcmd ...;" \ 100 "run uenvcmd;" \ 101 "fi;" \ 102 "if run mmc_load_uimage; then " \ 103 "run mmc_args;" \ 104 "bootm ${kloadaddr};" \ 105 "fi;" \ 106 "fi;" \ 107 "run nand_boot;" \ 108 "reset;" 109 110 #else 111 #define CONFIG_BOOTDELAY 0 112 113 #define CONFIG_BOOTCOMMAND \ 114 "setenv autoload no; " \ 115 "dhcp; " \ 116 "if tftp 80000000 debrick.scr; then " \ 117 "source 80000000; " \ 118 "fi" 119 #endif 120 121 #endif /* CONFIG_SPL_BUILD */ 122 123 #ifdef CONFIG_SPL_BUILD 124 #undef CONFIG_HW_WATCHDOG 125 #endif 126 127 #define CONFIG_VIDEO 128 #if defined(CONFIG_VIDEO) 129 #define CONFIG_VIDEO_DA8XX 130 #define CONFIG_CFB_CONSOLE 131 #define CONFIG_VGA_AS_SINGLE_DEVICE 132 #define CONFIG_SPLASH_SCREEN 133 #define CONFIG_SPLASH_SCREEN_ALIGN 134 #define CONFIG_VIDEO_LOGO 135 #define CONFIG_VIDEO_BMP_RLE8 136 #define CONFIG_VIDEO_BMP_LOGO 137 #define CONFIG_CMD_BMP 138 #define DA8XX_LCD_CNTL_BASE LCD_CNTL_BASE 139 140 #define CONFIG_SPI 141 #define CONFIG_OMAP3_SPI 142 143 #define BOARD_LCD_RESET 115 /* Bank 3 pin 19 */ 144 #define CONFIG_ARCH_EARLY_INIT_R 145 #define CONFIG_FORMIKE 146 #define DISPL_PLL_SPREAD_SPECTRUM 147 #define CONFIG_SYS_CONSOLE_BG_COL 0xff 148 #define CONFIG_SYS_CONSOLE_FG_COL 0x00 149 #endif 150 151 #endif /* ! __CONFIG_RUT_H */ 152