1 /* 2 * (C) Copyright 2013 Siemens Schweiz AG 3 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 4 * 5 * Based on: 6 * U-Boot file:/include/configs/am335x_evm.h 7 * 8 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_RASTABAN_H 14 #define __CONFIG_RASTABAN_H 15 16 #include "siemens-am33x-common.h" 17 18 #define DDR_PLL_FREQ 303 19 #undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC 20 21 /* FWD Button = 27 22 * SRV Button = 87 */ 23 #define BOARD_DFU_BUTTON_GPIO 27 24 #define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ 25 /* In dfu mode keep led1 on */ 26 #define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 27 "button_dfu0=27\0" \ 28 "button_dfu1=87\0" \ 29 "led0=3,0,1\0" \ 30 "led1=4,0,0\0" \ 31 "led2=5,0,1\0" \ 32 "led3=62,0,1\0" \ 33 "led4=60,0,1\0" \ 34 "led5=63,0,1\0" 35 36 /* Physical Memory Map */ 37 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 38 39 /* I2C Configuration */ 40 #define CONFIG_SYS_I2C_SPEED 100000 41 42 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 43 #define EEPROM_ADDR_DDR3 0x90 44 #define EEPROM_ADDR_CHIP 0x120 45 46 #undef CONFIG_MII 47 #undef CONFIG_PHY_GIGE 48 #define CONFIG_PHY_SMSC 49 50 #define CONFIG_FACTORYSET 51 52 /* Watchdog */ 53 #define CONFIG_OMAP_WATCHDOG 54 55 /* Define own nand partitions */ 56 #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 57 #define CONFIG_ENV_SIZE_REDUND 0x2000 58 #define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE) 59 60 #define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V3 61 62 #ifndef CONFIG_SPL_BUILD 63 64 /* Default env settings */ 65 #define CONFIG_EXTRA_ENV_SETTINGS \ 66 "hostname=rastaban\0" \ 67 "ubi_off=2048\0"\ 68 "nand_img_size=0x400000\0" \ 69 "optargs=\0" \ 70 "preboot=draco_led 0\0" \ 71 CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 72 CONFIG_ENV_SETTINGS_V2 \ 73 CONFIG_ENV_SETTINGS_NAND_V2 74 75 #ifndef CONFIG_RESTORE_FLASH 76 /* set to negative value for no autoboot */ 77 78 #define CONFIG_BOOTCOMMAND \ 79 "if dfubutton; then " \ 80 "run dfu_start; " \ 81 "reset; " \ 82 "fi;" \ 83 "run nand_boot;" \ 84 "run nand_boot_backup;" \ 85 "reset;" 86 87 #else 88 89 #define CONFIG_BOOTCOMMAND \ 90 "setenv autoload no; " \ 91 "dhcp; " \ 92 "if tftp 80000000 debrick.scr; then " \ 93 "source 80000000; " \ 94 "fi" 95 #endif 96 #endif /* CONFIG_SPL_BUILD */ 97 #endif /* ! __CONFIG_RASTABAN_H */ 98