1 /* 2 * (C) Copyright 2013 Siemens Schweiz AG 3 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 4 * 5 * Based on: 6 * U-Boot file:/include/configs/am335x_evm.h 7 * 8 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_RASTABAN_H 14 #define __CONFIG_RASTABAN_H 15 16 #include "siemens-am33x-common.h" 17 18 #define CONFIG_DISPLAY_CPUINFO 19 #define CONFIG_SYS_MPUCLK 300 20 #define DDR_PLL_FREQ 303 21 #undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC 22 23 /* FWD Button = 27 24 * SRV Button = 87 */ 25 #define BOARD_DFU_BUTTON_GPIO 27 26 #define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ 27 /* In dfu mode keep led1 on */ 28 #define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 29 "button_dfu0=27\0" \ 30 "button_dfu1=87\0" \ 31 "led0=3,0,1\0" \ 32 "led1=4,0,0\0" \ 33 "led2=5,0,1\0" \ 34 "led3=62,0,1\0" \ 35 "led4=60,0,1\0" \ 36 "led5=63,0,1\0" 37 38 #undef CONFIG_DOS_PARTITION 39 40 #define CONFIG_BOARD_LATE_INIT 41 42 /* Physical Memory Map */ 43 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 44 45 /* I2C Configuration */ 46 #define CONFIG_SYS_I2C_SPEED 100000 47 48 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 49 #define EEPROM_ADDR_DDR3 0x90 50 #define EEPROM_ADDR_CHIP 0x120 51 52 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300 53 54 #undef CONFIG_SPL_NET_SUPPORT 55 #undef CONFIG_SPL_NET_VCI_STRING 56 #undef CONFIG_SPL_ETH_SUPPORT 57 58 #undef CONFIG_MII 59 #undef CONFIG_PHY_GIGE 60 #define CONFIG_PHY_SMSC 61 62 #define CONFIG_FACTORYSET 63 64 /* Watchdog */ 65 #define CONFIG_OMAP_WATCHDOG 66 67 /* Define own nand partitions */ 68 #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 69 #define CONFIG_ENV_SIZE_REDUND 0x2000 70 #define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE) 71 72 #define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V3 73 74 #ifndef CONFIG_SPL_BUILD 75 76 /* Default env settings */ 77 #define CONFIG_EXTRA_ENV_SETTINGS \ 78 "hostname=rastaban\0" \ 79 "nand_img_size=0x400000\0" \ 80 "optargs=\0" \ 81 "preboot=draco_led 0\0" \ 82 CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 83 CONFIG_ENV_SETTINGS_V2 \ 84 CONFIG_ENV_SETTINGS_NAND_V2 85 86 #ifndef CONFIG_RESTORE_FLASH 87 /* set to negative value for no autoboot */ 88 #define CONFIG_BOOTDELAY 3 89 90 #define CONFIG_BOOTCOMMAND \ 91 "if dfubutton; then " \ 92 "run dfu_start; " \ 93 "reset; " \ 94 "fi;" \ 95 "run nand_boot;" \ 96 "run nand_boot_backup;" \ 97 "reset;" 98 99 #else 100 #define CONFIG_BOOTDELAY 0 101 102 #define CONFIG_BOOTCOMMAND \ 103 "setenv autoload no; " \ 104 "dhcp; " \ 105 "if tftp 80000000 debrick.scr; then " \ 106 "source 80000000; " \ 107 "fi" 108 #endif 109 #endif /* CONFIG_SPL_BUILD */ 110 #endif /* ! __CONFIG_RASTABAN_H */ 111