1 /* 2 * (C) Copyright 2013 Siemens Schweiz AG 3 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 4 * 5 * Based on: 6 * U-Boot file:/include/configs/am335x_evm.h 7 * 8 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_RASTABAN_H 14 #define __CONFIG_RASTABAN_H 15 16 #include "siemens-am33x-common.h" 17 18 #define CONFIG_SYS_MPUCLK 300 19 #define DDR_PLL_FREQ 303 20 #undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC 21 22 /* FWD Button = 27 23 * SRV Button = 87 */ 24 #define BOARD_DFU_BUTTON_GPIO 27 25 #define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ 26 /* In dfu mode keep led1 on */ 27 #define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 28 "button_dfu0=27\0" \ 29 "button_dfu1=87\0" \ 30 "led0=3,0,1\0" \ 31 "led1=4,0,0\0" \ 32 "led2=5,0,1\0" \ 33 "led3=62,0,1\0" \ 34 "led4=60,0,1\0" \ 35 "led5=63,0,1\0" 36 37 /* Physical Memory Map */ 38 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 39 40 /* I2C Configuration */ 41 #define CONFIG_SYS_I2C_SPEED 100000 42 43 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 44 #define EEPROM_ADDR_DDR3 0x90 45 #define EEPROM_ADDR_CHIP 0x120 46 47 #undef CONFIG_MII 48 #undef CONFIG_PHY_GIGE 49 #define CONFIG_PHY_SMSC 50 51 #define CONFIG_FACTORYSET 52 53 /* Watchdog */ 54 #define CONFIG_OMAP_WATCHDOG 55 56 /* Define own nand partitions */ 57 #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 58 #define CONFIG_ENV_SIZE_REDUND 0x2000 59 #define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE) 60 61 #define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V3 62 63 #ifndef CONFIG_SPL_BUILD 64 65 /* Default env settings */ 66 #define CONFIG_EXTRA_ENV_SETTINGS \ 67 "hostname=rastaban\0" \ 68 "ubi_off=2048\0"\ 69 "nand_img_size=0x400000\0" \ 70 "optargs=\0" \ 71 "preboot=draco_led 0\0" \ 72 CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 73 CONFIG_ENV_SETTINGS_V2 \ 74 CONFIG_ENV_SETTINGS_NAND_V2 75 76 #ifndef CONFIG_RESTORE_FLASH 77 /* set to negative value for no autoboot */ 78 79 #define CONFIG_BOOTCOMMAND \ 80 "if dfubutton; then " \ 81 "run dfu_start; " \ 82 "reset; " \ 83 "fi;" \ 84 "run nand_boot;" \ 85 "run nand_boot_backup;" \ 86 "reset;" 87 88 #else 89 90 #define CONFIG_BOOTCOMMAND \ 91 "setenv autoload no; " \ 92 "dhcp; " \ 93 "if tftp 80000000 debrick.scr; then " \ 94 "source 80000000; " \ 95 "fi" 96 #endif 97 #endif /* CONFIG_SPL_BUILD */ 98 #endif /* ! __CONFIG_RASTABAN_H */ 99