1 /* 2 * (C) Copyright 2013 Siemens Schweiz AG 3 * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de. 4 * 5 * Based on: 6 * U-Boot file:/include/configs/am335x_evm.h 7 * 8 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_RASTABAN_H 14 #define __CONFIG_RASTABAN_H 15 16 #include "siemens-am33x-common.h" 17 18 #define CONFIG_SYS_MPUCLK 300 19 #define DDR_PLL_FREQ 303 20 #undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC 21 22 /* FWD Button = 27 23 * SRV Button = 87 */ 24 #define BOARD_DFU_BUTTON_GPIO 27 25 #define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ 26 /* In dfu mode keep led1 on */ 27 #define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 28 "button_dfu0=27\0" \ 29 "button_dfu1=87\0" \ 30 "led0=3,0,1\0" \ 31 "led1=4,0,0\0" \ 32 "led2=5,0,1\0" \ 33 "led3=62,0,1\0" \ 34 "led4=60,0,1\0" \ 35 "led5=63,0,1\0" 36 37 #undef CONFIG_DOS_PARTITION 38 39 /* Physical Memory Map */ 40 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 41 42 /* I2C Configuration */ 43 #define CONFIG_SYS_I2C_SPEED 100000 44 45 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 46 #define EEPROM_ADDR_DDR3 0x90 47 #define EEPROM_ADDR_CHIP 0x120 48 49 #undef CONFIG_MII 50 #undef CONFIG_PHY_GIGE 51 #define CONFIG_PHY_SMSC 52 53 #define CONFIG_FACTORYSET 54 55 /* Watchdog */ 56 #define CONFIG_OMAP_WATCHDOG 57 58 /* Define own nand partitions */ 59 #define CONFIG_ENV_OFFSET_REDUND 0x2E0000 60 #define CONFIG_ENV_SIZE_REDUND 0x2000 61 #define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE) 62 63 #define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V3 64 65 #ifndef CONFIG_SPL_BUILD 66 67 /* Default env settings */ 68 #define CONFIG_EXTRA_ENV_SETTINGS \ 69 "hostname=rastaban\0" \ 70 "ubi_off=2048\0"\ 71 "nand_img_size=0x400000\0" \ 72 "optargs=\0" \ 73 "preboot=draco_led 0\0" \ 74 CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \ 75 CONFIG_ENV_SETTINGS_V2 \ 76 CONFIG_ENV_SETTINGS_NAND_V2 77 78 #ifndef CONFIG_RESTORE_FLASH 79 /* set to negative value for no autoboot */ 80 81 #define CONFIG_BOOTCOMMAND \ 82 "if dfubutton; then " \ 83 "run dfu_start; " \ 84 "reset; " \ 85 "fi;" \ 86 "run nand_boot;" \ 87 "run nand_boot_backup;" \ 88 "reset;" 89 90 #else 91 92 #define CONFIG_BOOTCOMMAND \ 93 "setenv autoload no; " \ 94 "dhcp; " \ 95 "if tftp 80000000 debrick.scr; then " \ 96 "source 80000000; " \ 97 "fi" 98 #endif 99 #endif /* CONFIG_SPL_BUILD */ 100 #endif /* ! __CONFIG_RASTABAN_H */ 101