xref: /openbmc/u-boot/include/configs/rastaban.h (revision 12308b12)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * (C) Copyright 2013 Siemens Schweiz AG
4  * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
5  *
6  * Based on:
7  * U-Boot file:/include/configs/am335x_evm.h
8  *
9  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
10  */
11 
12 #ifndef __CONFIG_RASTABAN_H
13 #define __CONFIG_RASTABAN_H
14 
15 #include "siemens-am33x-common.h"
16 
17 #define DDR_PLL_FREQ	303
18 
19 /* FWD Button = 27
20  * SRV Button = 87 */
21 #define BOARD_DFU_BUTTON_GPIO	27
22 #define GPIO_LAN9303_NRST	88	/* GPIO2_24 = gpio88 */
23 /* In dfu mode keep led1 on */
24 #define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
25 	"button_dfu0=27\0" \
26 	"button_dfu1=87\0" \
27 	"led0=3,0,1\0" \
28 	"led1=4,0,0\0" \
29 	"led2=5,0,1\0" \
30 	"led3=62,0,1\0" \
31 	"led4=60,0,1\0" \
32 	"led5=63,0,1\0"
33 
34  /* Physical Memory Map */
35 #define CONFIG_MAX_RAM_BANK_SIZE	(1024 << 20)	/* 1GB */
36 
37 /* I2C Configuration */
38 #define CONFIG_SYS_I2C_SPEED		100000
39 
40 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
41 #define EEPROM_ADDR_DDR3 0x90
42 #define EEPROM_ADDR_CHIP 0x120
43 
44 #undef CONFIG_MII
45 #define CONFIG_PHY_SMSC
46 
47 #define CONFIG_FACTORYSET
48 
49 /* Define own nand partitions */
50 #define CONFIG_ENV_OFFSET_REDUND	0x2E0000
51 #define CONFIG_ENV_SIZE_REDUND		0x2000
52 #define CONFIG_ENV_RANGE		(4 * CONFIG_SYS_ENV_SECT_SIZE)
53 
54 #ifndef CONFIG_SPL_BUILD
55 
56 /* Default env settings */
57 #define CONFIG_EXTRA_ENV_SETTINGS \
58 	"hostname=rastaban\0" \
59 	"ubi_off=2048\0"\
60 	"nand_img_size=0x400000\0" \
61 	"optargs=\0" \
62 	"preboot=draco_led 0\0" \
63 	CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
64 	CONFIG_ENV_SETTINGS_V2 \
65 	CONFIG_ENV_SETTINGS_NAND_V2
66 
67 #ifndef CONFIG_RESTORE_FLASH
68 /* set to negative value for no autoboot */
69 
70 #define CONFIG_BOOTCOMMAND \
71 "if dfubutton; then " \
72 	"run dfu_start; " \
73 	"reset; " \
74 "fi;" \
75 "run nand_boot;" \
76 "run nand_boot_backup;" \
77 "reset;"
78 
79 #else
80 
81 #define CONFIG_BOOTCOMMAND			\
82 	"setenv autoload no; "			\
83 	"dhcp; "				\
84 	"if tftp 80000000 debrick.scr; then "	\
85 		"source 80000000; "		\
86 	"fi"
87 #endif
88 #endif	/* CONFIG_SPL_BUILD */
89 #endif	/* ! __CONFIG_RASTABAN_H */
90