1 /* 2 * Copyright 2011-2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * Corenet DS style board configuration file 9 */ 10 #ifndef __QEMU_PPCE500_H 11 #define __QEMU_PPCE500_H 12 13 #define CONFIG_CMD_REGINFO 14 15 /* High Level Configuration Options */ 16 #define CONFIG_BOOKE 17 #define CONFIG_E500 /* BOOKE e500 family */ 18 #define CONFIG_QEMU_E500 19 20 #undef CONFIG_SYS_TEXT_BASE 21 #define CONFIG_SYS_TEXT_BASE 0xf01000 /* 15 MB */ 22 23 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 24 25 #define CONFIG_SYS_RAMBOOT 26 27 #define CONFIG_PCI /* Enable PCI/PCIE */ 28 #define CONFIG_PCI1 1 /* PCI controller 1 */ 29 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 30 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 31 32 #define CONFIG_ENV_OVERWRITE 33 34 #define CONFIG_ENABLE_36BIT_PHYS 35 36 #define CONFIG_ADDR_MAP 37 #define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ 38 39 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 40 #define CONFIG_SYS_MEMTEST_END 0x00400000 41 #define CONFIG_SYS_ALT_MEMTEST 42 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 43 44 /* Needed to fill the ccsrbar pointer */ 45 #define CONFIG_BOARD_EARLY_INIT_F 46 47 /* Virtual address to CCSRBAR */ 48 #define CONFIG_SYS_CCSRBAR 0xe0000000 49 /* Physical address should be a function call */ 50 #ifndef __ASSEMBLY__ 51 extern unsigned long long get_phys_ccsrbar_addr_early(void); 52 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH (get_phys_ccsrbar_addr_early() >> 32) 53 #define CONFIG_SYS_CCSRBAR_PHYS_LOW get_phys_ccsrbar_addr_early() 54 #else 55 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 56 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 57 #endif 58 59 #define CONFIG_PHYS_64BIT 60 61 /* Virtual address range for PCI region maps */ 62 #define CONFIG_SYS_PCI_MAP_START 0x80000000 63 #define CONFIG_SYS_PCI_MAP_END 0xe8000000 64 65 /* Virtual address to a temporary map if we need it (max 128MB) */ 66 #define CONFIG_SYS_TMPVIRT 0xe8000000 67 68 /* 69 * DDR Setup 70 */ 71 #define CONFIG_VERY_BIG_RAM 72 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 73 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 74 75 #define CONFIG_CHIP_SELECTS_PER_CTRL 0 76 77 #define CONFIG_SYS_CLK_FREQ 33000000 78 79 #define CONFIG_SYS_NO_FLASH 80 81 #define CONFIG_SYS_BOOT_BLOCK 0x00000000 /* boot TLB */ 82 83 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 84 85 #define CONFIG_ENV_IS_NOWHERE 86 87 #define CONFIG_HWCONFIG 88 89 #define CONFIG_SYS_INIT_RAM_ADDR 0x00100000 90 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0x0 91 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0x00100000 92 /* The assembler doesn't like typecast */ 93 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 94 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 95 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 96 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 97 98 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 99 GENERATED_GBL_DATA_SIZE) 100 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 101 102 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) 103 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 104 105 #define CONFIG_CONS_INDEX 1 106 #define CONFIG_SYS_NS16550 107 #define CONFIG_SYS_NS16550_SERIAL 108 #define CONFIG_SYS_NS16550_REG_SIZE 1 109 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) 110 111 #define CONFIG_SYS_BAUDRATE_TABLE \ 112 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 113 114 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 115 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 116 117 /* Use the HUSH parser */ 118 #define CONFIG_SYS_HUSH_PARSER 119 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 120 121 /* pass open firmware flat tree */ 122 #define CONFIG_OF_LIBFDT 123 #define CONFIG_OF_BOARD_SETUP 124 #define CONFIG_OF_STDOUT_VIA_ALIAS 125 126 /* new uImage format support */ 127 #define CONFIG_FIT 128 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 129 130 /* 131 * General PCI 132 * Memory space is mapped 1-1, but I/O space must start from 0. 133 */ 134 135 #ifdef CONFIG_PCI 136 #define CONFIG_PCI_INDIRECT_BRIDGE 137 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 138 139 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 140 #define CONFIG_DOS_PARTITION 141 #endif /* CONFIG_PCI */ 142 143 #define CONFIG_LBA48 144 #define CONFIG_DOS_PARTITION 145 #define CONFIG_CMD_EXT2 146 147 /* 148 * Environment 149 */ 150 #define CONFIG_ENV_SIZE 0x2000 151 152 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 153 154 #define CONFIG_LAST_STAGE_INIT 155 156 /* 157 * Command line configuration. 158 */ 159 #define CONFIG_CMD_DHCP 160 #define CONFIG_CMD_BOOTZ 161 #define CONFIG_CMD_GREPENV 162 #define CONFIG_CMD_IRQ 163 #define CONFIG_CMD_PING 164 165 #ifdef CONFIG_PCI 166 #define CONFIG_CMD_PCI 167 #endif 168 169 /* 170 * Miscellaneous configurable options 171 */ 172 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 173 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 174 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 175 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 176 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 177 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 178 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 179 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 180 181 /* 182 * For booting Linux, the board info and command line data 183 * have to be in the first 64 MB of memory, since this is 184 * the maximum mapped by the Linux kernel during initialization. 185 */ 186 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 187 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 188 189 /* 190 * Environment Configuration 191 */ 192 #define CONFIG_ROOTPATH "/opt/nfsroot" 193 #define CONFIG_BOOTFILE "uImage" 194 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ 195 196 /* default location for tftp and bootm */ 197 #define CONFIG_LOADADDR 1000000 198 199 #define CONFIG_BAUDRATE 115200 200 201 #define CONFIG_BOOTDELAY 1 202 #define CONFIG_BOOTCOMMAND \ 203 "test -n \"$qemu_kernel_addr\" && bootm $qemu_kernel_addr - $fdt_addr_r\0" 204 205 #endif /* __QEMU_PPCE500_H */ 206