1 /* 2 * (C) Copyright 2010 3 * Ilko Iliev <iliev@ronetix.at> 4 * Asen Dimov <dimov@ronetix.at> 5 * Ronetix GmbH <www.ronetix.at> 6 * 7 * (C) Copyright 2007-2008 8 * Stelian Pop <stelian@popies.net> 9 * Lead Tech Design <www.leadtechdesign.com> 10 * 11 * Configuation settings for the PM9G45 board. 12 * 13 * SPDX-License-Identifier: GPL-2.0+ 14 */ 15 16 #ifndef __CONFIG_H 17 #define __CONFIG_H 18 19 /* 20 * SoC must be defined first, before hardware.h is included. 21 * In this case SoC is defined in boards.cfg. 22 */ 23 #include <asm/hardware.h> 24 25 #define CONFIG_SYS_GENERIC_BOARD 26 27 #define CONFIG_PM9G45 1 /* It's an Ronetix PM9G45 */ 28 #define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9G45" 29 30 #define MACH_TYPE_PM9G45 2672 31 #define CONFIG_MACH_TYPE MACH_TYPE_PM9G45 32 33 /* ARM asynchronous clock */ 34 #define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ 35 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ 36 #define CONFIG_SYS_TEXT_BASE 0x73f00000 37 38 #define CONFIG_ARCH_CPU_INIT 39 40 #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ 41 #define CONFIG_SETUP_MEMORY_TAGS 1 42 #define CONFIG_INITRD_TAG 1 43 44 #define CONFIG_SKIP_LOWLEVEL_INIT 45 #define CONFIG_BOARD_EARLY_INIT_F 46 47 /* 48 * Hardware drivers 49 */ 50 #define CONFIG_AT91_GPIO 1 51 #define CONFIG_ATMEL_USART 1 52 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 53 #define CONFIG_USART_ID ATMEL_ID_SYS 54 55 #define CONFIG_SYS_USE_NANDFLASH 1 56 57 /* LED */ 58 #define CONFIG_AT91_LED 59 #define CONFIG_RED_LED GPIO_PIN_PD(31) /* this is the user1 led */ 60 #define CONFIG_GREEN_LED GPIO_PIN_PD(0) /* this is the user2 led */ 61 62 #define CONFIG_BOOTDELAY 3 63 64 /* 65 * BOOTP options 66 */ 67 #define CONFIG_BOOTP_BOOTFILESIZE 1 68 #define CONFIG_BOOTP_BOOTPATH 1 69 #define CONFIG_BOOTP_GATEWAY 1 70 #define CONFIG_BOOTP_HOSTNAME 1 71 72 /* 73 * Command line configuration. 74 */ 75 #define CONFIG_CMD_CACHE 76 #define CONFIG_CMD_PING 1 77 #define CONFIG_CMD_DHCP 1 78 #define CONFIG_CMD_NAND 1 79 #define CONFIG_CMD_USB 1 80 81 #define CONFIG_CMD_JFFS2 1 82 #define CONFIG_JFFS2_CMDLINE 1 83 #define CONFIG_JFFS2_NAND 1 84 #define CONFIG_JFFS2_DEV "nand0" /* NAND dev jffs2 lives on */ 85 #define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ 86 #define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition */ 87 88 /* SDRAM */ 89 #define CONFIG_NR_DRAM_BANKS 1 90 #define PHYS_SDRAM 0x70000000 91 #define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */ 92 93 /* NOR flash, not available */ 94 #define CONFIG_SYS_NO_FLASH 1 95 96 /* NAND flash */ 97 #ifdef CONFIG_CMD_NAND 98 #define CONFIG_NAND_ATMEL 99 #define CONFIG_SYS_MAX_NAND_DEVICE 1 100 #define CONFIG_SYS_NAND_BASE 0x40000000 101 #define CONFIG_SYS_NAND_DBW_8 1 102 /* our ALE is AD21 */ 103 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 104 /* our CLE is AD22 */ 105 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 106 #define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) 107 #define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PD(3) 108 109 #endif 110 111 /* Ethernet */ 112 #define CONFIG_MACB 1 113 #define CONFIG_RMII 1 114 #define CONFIG_NET_RETRY_COUNT 20 115 #define CONFIG_RESET_PHY_R 1 116 117 /* USB */ 118 #define CONFIG_USB_ATMEL 119 #define CONFIG_USB_ATMEL_CLK_SEL_UPLL 120 #define CONFIG_USB_OHCI_NEW 1 121 #define CONFIG_DOS_PARTITION 1 122 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 123 #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */ 124 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45" 125 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 126 #define CONFIG_USB_STORAGE 1 127 128 /* board specific(not enough SRAM) */ 129 #define CONFIG_AT91SAM9G45_LCD_BASE PHYS_SDRAM + 0xE00000 130 131 #define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM + 0x2000000 /* load addr */ 132 133 #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM 134 #define CONFIG_SYS_MEMTEST_END CONFIG_AT91SAM9G45_LCD_BASE 135 136 /* bootstrap + u-boot + env + linux in nandflash */ 137 #define CONFIG_ENV_IS_IN_NAND 1 138 #define CONFIG_ENV_OFFSET 0x60000 139 #define CONFIG_ENV_OFFSET_REDUND 0x80000 140 #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ 141 #define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm" 142 #define CONFIG_BOOTARGS "fbcon=rotate:3 console=tty0 " \ 143 "console=ttyS0,115200 " \ 144 "root=/dev/mtdblock4 " \ 145 "mtdparts=atmel_nand:128k(bootstrap)ro," \ 146 "256k(uboot)ro,1664k(env)," \ 147 "2M(linux)ro,-(root) rw " \ 148 "rootfstype=jffs2" 149 150 #define CONFIG_BAUDRATE 115200 151 152 #define CONFIG_SYS_CBSIZE 256 153 #define CONFIG_SYS_MAXARGS 16 154 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 155 sizeof(CONFIG_SYS_PROMPT) + 16) 156 #define CONFIG_SYS_LONGHELP 1 157 #define CONFIG_CMDLINE_EDITING 1 158 #define CONFIG_AUTO_COMPLETE 159 #define CONFIG_SYS_HUSH_PARSER 160 161 /* 162 * Size of malloc() pool 163 */ 164 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\ 165 0x1000) 166 167 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 168 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ 169 GENERATED_GBL_DATA_SIZE) 170 171 #endif 172