1 /* 2 * (C) Copyright 2007-2008 3 * Stelian Pop <stelian@popies.net> 4 * Lead Tech Design <www.leadtechdesign.com> 5 * Ilko Iliev <www.ronetix.at> 6 * 7 * Configuation settings for the RONETIX PM9263 board. 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #ifndef __CONFIG_H 13 #define __CONFIG_H 14 15 /* 16 * SoC must be defined first, before hardware.h is included. 17 * In this case SoC is defined in boards.cfg. 18 */ 19 #include <asm/hardware.h> 20 21 /* ARM asynchronous clock */ 22 23 #define MASTER_PLL_DIV 6 24 #define MASTER_PLL_MUL 65 25 #define MAIN_PLL_DIV 2 /* 2 or 4 */ 26 #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 27 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ 28 29 #define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9263" 30 #define CONFIG_PM9263 1 /* on a Ronetix PM9263 Board */ 31 #define CONFIG_ARCH_CPU_INIT 32 #define CONFIG_SYS_TEXT_BASE 0 33 34 #define CONFIG_MACH_TYPE MACH_TYPE_PM9263 35 36 /* clocks */ 37 #define CONFIG_SYS_MOR_VAL \ 38 (AT91_PMC_MOR_MOSCEN | \ 39 (255 << 8)) /* Main Oscillator Start-up Time */ 40 #define CONFIG_SYS_PLLAR_VAL \ 41 (AT91_PMC_PLLAR_29 | /* Bit 29 must be 1 when prog */ \ 42 AT91_PMC_PLLXR_OUT(3) | \ 43 AT91_PMC_PLLXR_PLLCOUNT(0x3f) | /* PLL Counter */\ 44 (2 << 28) | /* PLL Clock Frequency Range */ \ 45 ((MASTER_PLL_MUL - 1) << 16) | (MASTER_PLL_DIV)) 46 47 #if (MAIN_PLL_DIV == 2) 48 /* PCK/2 = MCK Master Clock from PLLA */ 49 #define CONFIG_SYS_MCKR1_VAL \ 50 (AT91_PMC_MCKR_CSS_SLOW | \ 51 AT91_PMC_MCKR_PRES_1 | \ 52 AT91_PMC_MCKR_MDIV_2) 53 /* PCK/2 = MCK Master Clock from PLLA */ 54 #define CONFIG_SYS_MCKR2_VAL \ 55 (AT91_PMC_MCKR_CSS_PLLA | \ 56 AT91_PMC_MCKR_PRES_1 | \ 57 AT91_PMC_MCKR_MDIV_2) 58 #else 59 /* PCK/4 = MCK Master Clock from PLLA */ 60 #define CONFIG_SYS_MCKR1_VAL \ 61 (AT91_PMC_MCKR_CSS_SLOW | \ 62 AT91_PMC_MCKR_PRES_1 | \ 63 AT91_PMC_MCKR_MDIV_4) 64 /* PCK/4 = MCK Master Clock from PLLA */ 65 #define CONFIG_SYS_MCKR2_VAL \ 66 (AT91_PMC_MCKR_CSS_PLLA | \ 67 AT91_PMC_MCKR_PRES_1 | \ 68 AT91_PMC_MCKR_MDIV_4) 69 #endif 70 /* define PDC[31:16] as DATA[31:16] */ 71 #define CONFIG_SYS_PIOD_PDR_VAL1 0xFFFF0000 72 /* no pull-up for D[31:16] */ 73 #define CONFIG_SYS_PIOD_PPUDR_VAL 0xFFFF0000 74 /* EBI0_CSA, CS1 SDRAM, CS3 NAND Flash, 3.3V memories */ 75 #define CONFIG_SYS_MATRIX_EBI0CSA_VAL \ 76 (AT91_MATRIX_CSA_DBPUC | AT91_MATRIX_CSA_VDDIOMSEL_3_3V | \ 77 AT91_MATRIX_CSA_EBI_CS1A) 78 79 /* SDRAM */ 80 /* SDRAMC_MR Mode register */ 81 #define CONFIG_SYS_SDRC_MR_VAL1 0 82 /* SDRAMC_TR - Refresh Timer register */ 83 #define CONFIG_SYS_SDRC_TR_VAL1 0x3AA 84 /* SDRAMC_CR - Configuration register*/ 85 #define CONFIG_SYS_SDRC_CR_VAL \ 86 (AT91_SDRAMC_NC_9 | \ 87 AT91_SDRAMC_NR_13 | \ 88 AT91_SDRAMC_NB_4 | \ 89 AT91_SDRAMC_CAS_2 | \ 90 AT91_SDRAMC_DBW_32 | \ 91 (2 << 8) | /* tWR - Write Recovery Delay */ \ 92 (7 << 12) | /* tRC - Row Cycle Delay */ \ 93 (2 << 16) | /* tRP - Row Precharge Delay */ \ 94 (2 << 20) | /* tRCD - Row to Column Delay */ \ 95 (5 << 24) | /* tRAS - Active to Precharge Delay */ \ 96 (8 << 28)) /* tXSR - Exit Self Refresh to Active Delay */ 97 98 /* Memory Device Register -> SDRAM */ 99 #define CONFIG_SYS_SDRC_MDR_VAL AT91_SDRAMC_MD_SDRAM 100 #define CONFIG_SYS_SDRC_MR_VAL2 AT91_SDRAMC_MODE_PRECHARGE 101 #define CONFIG_SYS_SDRAM_VAL1 0 /* SDRAM_BASE */ 102 #define CONFIG_SYS_SDRC_MR_VAL3 AT91_SDRAMC_MODE_REFRESH 103 #define CONFIG_SYS_SDRAM_VAL2 0 /* SDRAM_BASE */ 104 #define CONFIG_SYS_SDRAM_VAL3 0 /* SDRAM_BASE */ 105 #define CONFIG_SYS_SDRAM_VAL4 0 /* SDRAM_BASE */ 106 #define CONFIG_SYS_SDRAM_VAL5 0 /* SDRAM_BASE */ 107 #define CONFIG_SYS_SDRAM_VAL6 0 /* SDRAM_BASE */ 108 #define CONFIG_SYS_SDRAM_VAL7 0 /* SDRAM_BASE */ 109 #define CONFIG_SYS_SDRAM_VAL8 0 /* SDRAM_BASE */ 110 #define CONFIG_SYS_SDRAM_VAL9 0 /* SDRAM_BASE */ 111 #define CONFIG_SYS_SDRC_MR_VAL4 AT91_SDRAMC_MODE_LMR 112 #define CONFIG_SYS_SDRAM_VAL10 0 /* SDRAM_BASE */ 113 #define CONFIG_SYS_SDRC_MR_VAL5 AT91_SDRAMC_MODE_NORMAL 114 #define CONFIG_SYS_SDRAM_VAL11 0 /* SDRAM_BASE */ 115 #define CONFIG_SYS_SDRC_TR_VAL2 1200 /* SDRAM_TR */ 116 #define CONFIG_SYS_SDRAM_VAL12 0 /* SDRAM_BASE */ 117 118 /* setup SMC0, CS0 (NOR Flash) - 16-bit, 15 WS */ 119 #define CONFIG_SYS_SMC0_SETUP0_VAL \ 120 (AT91_SMC_SETUP_NWE(10) | AT91_SMC_SETUP_NCS_WR(10) | \ 121 AT91_SMC_SETUP_NRD(10) | AT91_SMC_SETUP_NCS_RD(10)) 122 #define CONFIG_SYS_SMC0_PULSE0_VAL \ 123 (AT91_SMC_PULSE_NWE(11) | AT91_SMC_PULSE_NCS_WR(11) | \ 124 AT91_SMC_PULSE_NRD(11) | AT91_SMC_PULSE_NCS_RD(11)) 125 #define CONFIG_SYS_SMC0_CYCLE0_VAL \ 126 (AT91_SMC_CYCLE_NWE(22) | AT91_SMC_CYCLE_NRD(22)) 127 #define CONFIG_SYS_SMC0_MODE0_VAL \ 128 (AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | \ 129 AT91_SMC_MODE_DBW_16 | \ 130 AT91_SMC_MODE_TDF | \ 131 AT91_SMC_MODE_TDF_CYCLE(6)) 132 133 /* user reset enable */ 134 #define CONFIG_SYS_RSTC_RMR_VAL \ 135 (AT91_RSTC_KEY | \ 136 AT91_RSTC_CR_PROCRST | \ 137 AT91_RSTC_MR_ERSTL(1) | \ 138 AT91_RSTC_MR_ERSTL(2)) 139 140 /* Disable Watchdog */ 141 #define CONFIG_SYS_WDTC_WDMR_VAL \ 142 (AT91_WDT_MR_WDIDLEHLT | AT91_WDT_MR_WDDBGHLT | \ 143 AT91_WDT_MR_WDV(0xfff) | \ 144 AT91_WDT_MR_WDDIS | \ 145 AT91_WDT_MR_WDD(0xfff)) 146 147 #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ 148 #define CONFIG_SETUP_MEMORY_TAGS 1 149 #define CONFIG_INITRD_TAG 1 150 151 #undef CONFIG_SKIP_LOWLEVEL_INIT 152 #define CONFIG_USER_LOWLEVEL_INIT 1 153 154 /* 155 * Hardware drivers 156 */ 157 #define CONFIG_AT91_GPIO 1 158 #define CONFIG_ATMEL_USART 1 159 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 160 #define CONFIG_USART_ID ATMEL_ID_SYS 161 162 /* LCD */ 163 #define LCD_BPP LCD_COLOR8 164 #define CONFIG_LCD_LOGO 1 165 #undef LCD_TEST_PATTERN 166 #define CONFIG_LCD_INFO 1 167 #define CONFIG_LCD_INFO_BELOW_LOGO 1 168 #define CONFIG_ATMEL_LCD 1 169 #define CONFIG_ATMEL_LCD_BGR555 1 170 171 #define CONFIG_LCD_IN_PSRAM 1 172 173 /* LED */ 174 #define CONFIG_AT91_LED 175 #define CONFIG_RED_LED GPIO_PIN_PB(7) /* this is the power led */ 176 #define CONFIG_GREEN_LED GPIO_PIN_PB(8) /* this is the user1 led */ 177 178 179 /* 180 * BOOTP options 181 */ 182 #define CONFIG_BOOTP_BOOTFILESIZE 1 183 #define CONFIG_BOOTP_BOOTPATH 1 184 #define CONFIG_BOOTP_GATEWAY 1 185 #define CONFIG_BOOTP_HOSTNAME 1 186 187 /* 188 * Command line configuration. 189 */ 190 #define CONFIG_CMD_NAND 1 191 192 /* SDRAM */ 193 #define CONFIG_NR_DRAM_BANKS 1 194 #define PHYS_SDRAM 0x20000000 195 #define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ 196 197 /* DataFlash */ 198 #define CONFIG_ATMEL_DATAFLASH_SPI 199 #define CONFIG_HAS_DATAFLASH 1 200 #define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 201 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ 202 #define AT91_SPI_CLK 15000000 203 #define DATAFLASH_TCSS (0x1a << 16) 204 #define DATAFLASH_TCHS (0x1 << 24) 205 206 /* NOR flash, if populated */ 207 #define CONFIG_SYS_FLASH_CFI 1 208 #define CONFIG_FLASH_CFI_DRIVER 1 209 #define PHYS_FLASH_1 0x10000000 210 #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 211 #define CONFIG_SYS_MAX_FLASH_SECT 256 212 #define CONFIG_SYS_MAX_FLASH_BANKS 1 213 214 /* NAND flash */ 215 #ifdef CONFIG_CMD_NAND 216 #define CONFIG_NAND_ATMEL 217 #define CONFIG_SYS_MAX_NAND_DEVICE 1 218 #define CONFIG_SYS_NAND_BASE 0x40000000 219 #define CONFIG_SYS_NAND_DBW_8 1 220 /* our ALE is AD21 */ 221 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 222 /* our CLE is AD22 */ 223 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 224 #define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) 225 #define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PB(30) 226 227 #endif 228 229 #define CONFIG_JFFS2_CMDLINE 1 230 #define CONFIG_JFFS2_NAND 1 231 #define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */ 232 #define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ 233 #define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition size*/ 234 235 /* PSRAM */ 236 #define PHYS_PSRAM 0x70000000 237 #define PHYS_PSRAM_SIZE 0x00400000 /* 4MB */ 238 /* Slave EBI1, PSRAM connected */ 239 #define CONFIG_PSRAM_SCFG (AT91_MATRIX_SCFG_ARBT_FIXED_PRIORITY | \ 240 AT91_MATRIX_SCFG_FIXED_DEFMSTR(5) | \ 241 AT91_MATRIX_SCFG_DEFMSTR_TYPE_FIXED | \ 242 AT91_MATRIX_SCFG_SLOT_CYCLE(255)) 243 244 /* Ethernet */ 245 #define CONFIG_MACB 1 246 #define CONFIG_RMII 1 247 #define CONFIG_NET_RETRY_COUNT 20 248 #define CONFIG_RESET_PHY_R 1 249 250 /* USB */ 251 #define CONFIG_USB_ATMEL 252 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 253 #define CONFIG_USB_OHCI_NEW 1 254 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 255 #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000 /* AT91SAM9263_UHP_BASE */ 256 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263" 257 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 258 259 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 260 261 #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM 262 #define CONFIG_SYS_MEMTEST_END 0x23e00000 263 264 #define CONFIG_SYS_USE_FLASH 1 265 #undef CONFIG_SYS_USE_DATAFLASH 266 #undef CONFIG_SYS_USE_NANDFLASH 267 268 #ifdef CONFIG_SYS_USE_DATAFLASH 269 270 /* bootstrap + u-boot + env + linux in dataflash on CS0 */ 271 #define CONFIG_ENV_IS_IN_DATAFLASH 272 #define CFG_MONITOR_BASE (CFG_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400) 273 #define CONFIG_ENV_OFFSET 0x4200 274 #define CONFIG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET) 275 #define CONFIG_ENV_SIZE 0x4200 276 #define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm" 277 #define CONFIG_BOOTARGS "console=ttyS0,115200 " \ 278 "root=/dev/mtdblock0 " \ 279 "mtdparts=atmel_nand:-(root) "\ 280 "rw rootfstype=jffs2" 281 282 #elif defined(CONFIG_SYS_USE_NANDFLASH) /* CFG_USE_NANDFLASH */ 283 284 /* bootstrap + u-boot + env + linux in nandflash */ 285 #define CONFIG_ENV_IS_IN_NAND 286 #define CONFIG_ENV_OFFSET 0x60000 287 #define CONFIG_ENV_OFFSET_REDUND 0x80000 288 #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ 289 #define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm" 290 #define CONFIG_BOOTARGS "console=ttyS0,115200 " \ 291 "root=/dev/mtdblock5 " \ 292 "mtdparts=atmel_nand:" \ 293 "128k(bootstrap)ro," \ 294 "256k(uboot)ro," \ 295 "128k(env1)ro," \ 296 "128k(env2)ro," \ 297 "2M(linux)," \ 298 "-(root) " \ 299 "rw rootfstype=jffs2" 300 301 #elif defined(CONFIG_SYS_USE_FLASH) /* CFG_USE_FLASH */ 302 303 #define CONFIG_ENV_IS_IN_FLASH 1 304 #define CONFIG_ENV_OFFSET 0x40000 305 #define CONFIG_ENV_SECT_SIZE 0x10000 306 #define CONFIG_ENV_SIZE 0x10000 307 #define CONFIG_ENV_OVERWRITE 1 308 309 /* JFFS Partition offset set */ 310 #define CONFIG_SYS_JFFS2_FIRST_BANK 0 311 #define CONFIG_SYS_JFFS2_NUM_BANKS 1 312 313 /* 512k reserved for u-boot */ 314 #define CONFIG_SYS_JFFS2_FIRST_SECTOR 11 315 316 #define CONFIG_BOOTCOMMAND "run flashboot" 317 #define CONFIG_ROOTPATH "/ronetix/rootfs" 318 319 #define CONFIG_CON_ROT "fbcon=rotate:3 " 320 #define CONFIG_BOOTARGS "root=/dev/mtdblock4 rootfstype=jffs2 "\ 321 CONFIG_CON_ROT 322 323 #define MTDIDS_DEFAULT "nor0=physmap-flash.0,nand0=nand" 324 #define MTDPARTS_DEFAULT \ 325 "mtdparts=physmap-flash.0:" \ 326 "256k(u-boot)ro," \ 327 "64k(u-boot-env)ro," \ 328 "1408k(kernel)," \ 329 "-(rootfs);" \ 330 "nand:-(nand)" 331 332 #define CONFIG_EXTRA_ENV_SETTINGS \ 333 "mtdids=" MTDIDS_DEFAULT "\0" \ 334 "mtdparts=" MTDPARTS_DEFAULT "\0" \ 335 "partition=nand0,0\0" \ 336 "ramargs=setenv bootargs $(bootargs) $(mtdparts)\0" \ 337 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 338 CONFIG_CON_ROT \ 339 "nfsroot=$(serverip):$(rootpath) $(mtdparts)\0" \ 340 "addip=setenv bootargs $(bootargs) " \ 341 "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"\ 342 ":$(hostname):eth0:off\0" \ 343 "ramboot=tftpboot 0x22000000 vmImage;" \ 344 "run ramargs;run addip;bootm 22000000\0" \ 345 "nfsboot=tftpboot 0x22000000 vmImage;" \ 346 "run nfsargs;run addip;bootm 22000000\0" \ 347 "flashboot=run ramargs;run addip;bootm 0x10050000\0" \ 348 "" 349 350 #else 351 #error "Undefined memory device" 352 #endif 353 354 #define CONFIG_SYS_CBSIZE 256 355 #define CONFIG_SYS_MAXARGS 16 356 #define CONFIG_SYS_PBSIZE \ 357 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 358 #define CONFIG_SYS_LONGHELP 1 359 #define CONFIG_CMDLINE_EDITING 1 360 361 /* 362 * Size of malloc() pool 363 */ 364 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000) 365 366 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 367 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ 368 GENERATED_GBL_DATA_SIZE) 369 370 #endif 371