1 /*
2  * Configuration settings for the mini-box PICOSAM9G45 board.
3  * (C) Copyright 2015 Inter Act B.V.
4  *
5  * Based on:
6  * U-Boot file: include/configs/at91sam9m10g45ek.h
7  * (C) Copyright 2007-2008
8  * Stelian Pop <stelian@popies.net>
9  * Lead Tech Design <www.leadtechdesign.com>
10  *
11  * SPDX-License-Identifier:	GPL-2.0+
12  */
13 
14 #ifndef __CONFIG_H
15 #define __CONFIG_H
16 
17 #include <asm/hardware.h>
18 
19 #define CONFIG_SYS_TEXT_BASE		0x23f00000
20 
21 #define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
22 
23 /* ARM asynchronous clock */
24 #define CONFIG_SYS_AT91_SLOW_CLOCK      32768
25 #define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
26 
27 #define CONFIG_PICOSAM
28 
29 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs	*/
30 #define CONFIG_SETUP_MEMORY_TAGS
31 #define CONFIG_INITRD_TAG
32 #define CONFIG_SKIP_LOWLEVEL_INIT
33 
34 /* general purpose I/O */
35 #define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
36 #define CONFIG_AT91_GPIO
37 #define CONFIG_AT91_GPIO_PULLUP	1	/* keep pullups on peripheral pins */
38 
39 /* serial console */
40 #define CONFIG_ATMEL_USART
41 #define CONFIG_USART_BASE		ATMEL_BASE_DBGU
42 #define	CONFIG_USART_ID			ATMEL_ID_SYS
43 
44 /* LCD */
45 #define LCD_BPP				LCD_COLOR8
46 #define CONFIG_LCD_LOGO
47 #undef LCD_TEST_PATTERN
48 #define CONFIG_LCD_INFO
49 #define CONFIG_LCD_INFO_BELOW_LOGO
50 #define CONFIG_ATMEL_LCD
51 #define CONFIG_ATMEL_LCD_RGB565
52 /* board specific(not enough SRAM) */
53 #define CONFIG_AT91SAM9G45_LCD_BASE		0x23E00000
54 
55 /* LED */
56 #define CONFIG_AT91_LED
57 #define CONFIG_GREEN_LED	AT91_PIN_PD31	/* this is the user1 led */
58 
59 
60 /*
61  * BOOTP options
62  */
63 #define CONFIG_BOOTP_BOOTFILESIZE
64 #define CONFIG_BOOTP_BOOTPATH
65 #define CONFIG_BOOTP_GATEWAY
66 #define CONFIG_BOOTP_HOSTNAME
67 
68 /* Enable the watchdog */
69 #define CONFIG_AT91SAM9_WATCHDOG
70 #define CONFIG_HW_WATCHDOG
71 
72 /*
73  * Command line configuration.
74  */
75 
76 /* SDRAM */
77 #define CONFIG_NR_DRAM_BANKS	2
78 #define PHYS_SDRAM_1		ATMEL_BASE_CS1	/* on DDRSDRC1 */
79 #define PHYS_SDRAM_1_SIZE	0x08000000	/* 128 MB */
80 #define PHYS_SDRAM_2		ATMEL_BASE_CS6	/* on DDRSDRC0 */
81 #define PHYS_SDRAM_2_SIZE       0x08000000	/* 128 MB */
82 #define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM_1
83 
84 #define CONFIG_SYS_INIT_SP_ADDR \
85 	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
86 
87 /* MMC */
88 
89 #ifdef CONFIG_CMD_MMC
90 #define CONFIG_GENERIC_ATMEL_MCI
91 #endif
92 
93 /* Ethernet */
94 #define CONFIG_MACB
95 #define CONFIG_RMII
96 #define CONFIG_NET_RETRY_COUNT		20
97 #define CONFIG_RESET_PHY_R
98 #define CONFIG_AT91_WANTS_COMMON_PHY
99 
100 /* USB */
101 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	2
102 
103 #define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */
104 
105 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
106 #define CONFIG_SYS_MEMTEST_END		0x23e00000
107 
108 #ifdef CONFIG_SYS_USE_MMC
109 /* bootstrap + u-boot + env + linux in mmc */
110 #define FAT_ENV_INTERFACE	"mmc"
111 /*
112  * We don't specify the part number, if device 0 has partition table, it means
113  * the first partition; it no partition table, then take whole device as a
114  * FAT file system.
115  */
116 #define FAT_ENV_DEVICE_AND_PART	"0"
117 #define FAT_ENV_FILE		"uboot.env"
118 #define CONFIG_ENV_IS_IN_FAT
119 #define CONFIG_FAT_WRITE
120 #define CONFIG_ENV_SIZE		0x4000
121 
122 #define CONFIG_BOOTARGS		"console=ttyS0,115200 " \
123 				"root=/dev/mmcblk0p2 rw rootwait"
124 #define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x21000000 dtb; " \
125 				"fatload mmc 0:1 0x22000000 zImage; " \
126 				"bootz 0x22000000 - 0x21000000"
127 #endif
128 
129 #define CONFIG_SYS_CBSIZE	256
130 #define CONFIG_SYS_MAXARGS	16
131 #define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE  \
132 					+ sizeof(CONFIG_SYS_PROMPT) + 16)
133 #define CONFIG_SYS_LONGHELP
134 #define CONFIG_CMDLINE_EDITING
135 #define CONFIG_AUTO_COMPLETE
136 
137 /*
138  * Size of malloc() pool
139  */
140 #define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
141 
142 /* Defines for SPL */
143 #define CONFIG_SPL_FRAMEWORK
144 #define CONFIG_SPL_TEXT_BASE		0x300000
145 #define CONFIG_SPL_MAX_SIZE		0x010000
146 #define CONFIG_SPL_STACK		0x310000
147 
148 #define CONFIG_SYS_MONITOR_LEN		0x80000
149 
150 #ifdef CONFIG_SYS_USE_MMC
151 
152 #define CONFIG_SPL_BSS_START_ADDR	0x20000000
153 #define CONFIG_SPL_BSS_MAX_SIZE		0x00080000
154 #define CONFIG_SYS_SPL_MALLOC_START	0x20080000
155 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x00080000
156 
157 #define CONFIG_SPL_LDSCRIPT	arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
158 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
159 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
160 
161 #define CONFIG_SPL_ATMEL_SIZE
162 #define CONFIG_SYS_MASTER_CLOCK		132096000
163 #define CONFIG_SYS_AT91_PLLA		0x20c73f03
164 #define CONFIG_SYS_MCKR			0x1301
165 #define CONFIG_SYS_MCKR_CSS		0x1302
166 
167 #endif
168 #endif
169