1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Configuration settings for the mini-box PICOSAM9G45 board.
4  * (C) Copyright 2015 Inter Act B.V.
5  *
6  * Based on:
7  * U-Boot file: include/configs/at91sam9m10g45ek.h
8  * (C) Copyright 2007-2008
9  * Stelian Pop <stelian@popies.net>
10  * Lead Tech Design <www.leadtechdesign.com>
11  */
12 
13 #ifndef __CONFIG_H
14 #define __CONFIG_H
15 
16 #include <asm/hardware.h>
17 
18 #define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
19 
20 /* ARM asynchronous clock */
21 #define CONFIG_SYS_AT91_SLOW_CLOCK      32768
22 #define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
23 
24 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs	*/
25 #define CONFIG_SETUP_MEMORY_TAGS
26 #define CONFIG_INITRD_TAG
27 #define CONFIG_SKIP_LOWLEVEL_INIT
28 
29 /* general purpose I/O */
30 #define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
31 #define CONFIG_AT91_GPIO
32 #define CONFIG_AT91_GPIO_PULLUP	1	/* keep pullups on peripheral pins */
33 
34 /* serial console */
35 #define CONFIG_ATMEL_USART
36 #define CONFIG_USART_BASE		ATMEL_BASE_DBGU
37 #define	CONFIG_USART_ID			ATMEL_ID_SYS
38 
39 /* LCD */
40 #define LCD_BPP				LCD_COLOR8
41 #define CONFIG_LCD_LOGO
42 #undef LCD_TEST_PATTERN
43 #define CONFIG_LCD_INFO
44 #define CONFIG_LCD_INFO_BELOW_LOGO
45 #define CONFIG_ATMEL_LCD
46 #define CONFIG_ATMEL_LCD_RGB565
47 /* board specific(not enough SRAM) */
48 #define CONFIG_AT91SAM9G45_LCD_BASE		0x23E00000
49 
50 /* LED */
51 #define CONFIG_AT91_LED
52 #define CONFIG_GREEN_LED	AT91_PIN_PD31	/* this is the user1 led */
53 
54 
55 /*
56  * BOOTP options
57  */
58 #define CONFIG_BOOTP_BOOTFILESIZE
59 
60 /* Enable the watchdog */
61 #define CONFIG_AT91SAM9_WATCHDOG
62 #define CONFIG_HW_WATCHDOG
63 
64 /*
65  * Command line configuration.
66  */
67 
68 /* SDRAM */
69 #define PHYS_SDRAM_1		ATMEL_BASE_CS1	/* on DDRSDRC1 */
70 #define PHYS_SDRAM_1_SIZE	0x08000000	/* 128 MB */
71 #define PHYS_SDRAM_2		ATMEL_BASE_CS6	/* on DDRSDRC0 */
72 #define PHYS_SDRAM_2_SIZE       0x08000000	/* 128 MB */
73 #define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM_1
74 
75 #define CONFIG_SYS_INIT_SP_ADDR \
76 	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
77 
78 /* MMC */
79 
80 #ifdef CONFIG_CMD_MMC
81 #define CONFIG_GENERIC_ATMEL_MCI
82 #endif
83 
84 /* Ethernet */
85 #define CONFIG_MACB
86 #define CONFIG_RMII
87 #define CONFIG_NET_RETRY_COUNT		20
88 #define CONFIG_RESET_PHY_R
89 #define CONFIG_AT91_WANTS_COMMON_PHY
90 
91 #define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */
92 
93 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
94 #define CONFIG_SYS_MEMTEST_END		0x23e00000
95 
96 #ifdef CONFIG_SYS_USE_MMC
97 /* bootstrap + u-boot + env + linux in mmc */
98 #define CONFIG_ENV_SIZE		0x4000
99 
100 #define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x21000000 dtb; " \
101 				"fatload mmc 0:1 0x22000000 zImage; " \
102 				"bootz 0x22000000 - 0x21000000"
103 #endif
104 
105 /*
106  * Size of malloc() pool
107  */
108 #define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
109 
110 /* Defines for SPL */
111 #define CONFIG_SPL_TEXT_BASE		0x300000
112 #define CONFIG_SPL_MAX_SIZE		0x010000
113 #define CONFIG_SPL_STACK		0x310000
114 
115 #define CONFIG_SYS_MONITOR_LEN		0x80000
116 
117 #ifdef CONFIG_SYS_USE_MMC
118 
119 #define CONFIG_SPL_BSS_START_ADDR	0x20000000
120 #define CONFIG_SPL_BSS_MAX_SIZE		0x00080000
121 #define CONFIG_SYS_SPL_MALLOC_START	0x20080000
122 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x00080000
123 
124 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
125 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
126 
127 #define CONFIG_SPL_ATMEL_SIZE
128 #define CONFIG_SYS_MASTER_CLOCK		132096000
129 #define CONFIG_SYS_AT91_PLLA		0x20c73f03
130 #define CONFIG_SYS_MCKR			0x1301
131 #define CONFIG_SYS_MCKR_CSS		0x1302
132 
133 #endif
134 #endif
135