xref: /openbmc/u-boot/include/configs/pengwyn.h (revision afaea1f5)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * pengwyn.h
4  *
5  * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
6  *
7  * based on am335x_evm.h, Copyright (C) 2011 Texas Instruments Inc.
8  */
9 
10 #ifndef __CONFIG_PENGWYN_H
11 #define __CONFIG_PENGWYN_H
12 
13 
14 #include <configs/ti_am335x_common.h>
15 
16 /* Clock Defines */
17 #define V_OSCK				24000000
18 #define V_SCLK				V_OSCK
19 
20 /* set env size */
21 #define CONFIG_ENV_SIZE			0x4000
22 
23 #ifndef CONFIG_SPL_BUILD
24 #define CONFIG_EXTRA_ENV_SETTINGS \
25 	"loadaddr=0x80200000\0" \
26 	"fdtaddr=0x80F80000\0" \
27 	"bootpart=0:2\0" \
28 	"bootdir=/boot\0" \
29 	"bootfile=zImage\0" \
30 	"fdtfile=am335x-pengwyn.dtb\0" \
31 	"console=ttyO0,115200n8\0" \
32 	"optargs=\0" \
33 	"mmcdev=0\0" \
34 	"mmcroot=/dev/mmcblk0p2 ro\0" \
35 	"mmcrootfstype=ext4 rootwait\0" \
36 	"rootpath=/export/rootfs\0" \
37 	"nfsopts=nolock\0" \
38 	"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
39 		"::off\0" \
40 	"mmcargs=setenv bootargs console=${console} " \
41 		"${optargs} " \
42 		"root=${mmcroot} " \
43 		"rootfstype=${mmcrootfstype}\0" \
44 	"netargs=setenv bootargs console=${console} " \
45 		"${optargs} " \
46 		"root=/dev/nfs " \
47 		"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
48 		"ip=dhcp\0" \
49 	"bootenv=uEnv.txt\0" \
50 	"loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
51 	"importbootenv=echo Importing environment from mmc ...; " \
52 		"env import -t $loadaddr $filesize\0" \
53 	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
54 	"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
55 	"mmcloados=run mmcargs; " \
56 		"bootz ${loadaddr} - ${fdtaddr};\0" \
57 	"mmcboot=mmc dev ${mmcdev}; " \
58 		"if mmc rescan; then " \
59 			"echo SD/MMC found on device ${mmcdev};" \
60 			"if run loadbootenv; then " \
61 				"echo Loaded environment from ${bootenv};" \
62 				"run importbootenv;" \
63 			"fi;" \
64 			"if test -n $uenvcmd; then " \
65 				"echo Running uenvcmd ...;" \
66 				"run uenvcmd;" \
67 			"fi;" \
68 			"if run loadimage; then " \
69 				"run loadfdt;" \
70 				"run mmcloados;" \
71 			"fi;" \
72 		"fi;\0" \
73 	"netboot=echo Booting from network ...; " \
74 		"setenv autoload no; " \
75 		"dhcp; " \
76 		"tftp ${loadaddr} ${bootfile}; " \
77 		"tftp ${fdtaddr} ${fdtfile}; " \
78 		"run netargs; " \
79 		"bootz ${loadaddr} - ${fdtaddr}\0" \
80 	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
81 	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
82 	"nandargs=setenv bootargs console=${console} " \
83 		"${optargs} " \
84 		"root=${nandroot} " \
85 		"rootfstype=${nandrootfstype}\0" \
86 	"nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \
87 	"nandrootfstype=ubifs rootwait=1\0" \
88 	"nandboot=echo Booting from nand ...; " \
89 		"run nandargs; " \
90 		"nand read ${fdtaddr} u-boot-spl-os; " \
91 		"nand read ${loadaddr} kernel; " \
92 		"bootz ${loadaddr} - ${fdtaddr}\0"
93 #endif
94 
95 #define CONFIG_BOOTCOMMAND \
96 	"run mmcboot;" \
97 	"run nandboot;"
98 
99 /* NS16550 Configuration: primary UART via FTDI */
100 #define CONFIG_SYS_NS16550_COM1		0x44e09000
101 
102 /* I2C Configuration */
103 #define	CONFIG_SYS_I2C_SPEED		100000
104 #define CONFIG_ENV_EEPROM_IS_ON_I2C
105 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
106 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
107 
108 /* SPL */
109 
110 /* NAND support */
111 
112 /* NAND Configuration. */
113 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
114 #define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / \
115 					 CONFIG_SYS_NAND_PAGE_SIZE)
116 #define CONFIG_SYS_NAND_PAGE_SIZE	4096
117 #define CONFIG_SYS_NAND_OOBSIZE		224
118 #define CONFIG_SYS_NAND_ONFI_DETECTION
119 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128*4096)
120 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
121 #define CONFIG_SYS_NAND_ECCPOS		{   2,   3,   4,   5,   6,   7,   8,   9,  10,  11,  12,  13,  14,  15,  16,  17,\
122 					   18,  19,  20,  21,  22,  23,  24,  25,  26,  27,  28,  29,  30,  31,  32,  33,\
123 					   34,  35,  36,  37,  38,  39,  40,  41,  42,  43,  44,  45,  46,  47,  48,  49,\
124 					   50,  51,  52,  53,  54,  55,  56,  57,  58,  59,  60,  61,  62,  63,  64,  65,\
125 					   66,  67,  68,  69,  70,  71,  72,  73,  74,  75,  76,  77,  78,  79,  80,  81,\
126 					   82,  83,  84,  85,  86,  87,  88,  89,  90,  91,  92,  93,  94,  95,  96,  97,\
127 					   98,  99, 100, 101, 102, 103, 104, 105, 106, 107, 108, 109, 110, 111, 112, 113,\
128 					  114, 115, 116, 117, 118, 119, 120, 121, 122, 123, 124, 125, 126, 127, 128, 129, 130, 131, 132, 133,\
129 					  134, 135, 136, 137, 138, 139, 140, 141, 142, 143, 144, 145, 146, 147, 148, 149, 150, 151, 152, 153,\
130 					  154, 155, 156, 157, 158, 159, 160, 161, 162, 163, 164, 165, 166, 167, 168, 169, 170, 171, 172, 173,\
131 					  174, 175, 176, 177, 178, 179, 180, 181, 182, 183, 184, 185, 186, 187, 188, 189, 190, 191, 192, 193,\
132 					  194, 195, 196, 197, 198, 199, 200, 201, 202, 203, 204, 205, 206, 207, 208, 209}
133 
134 #define CONFIG_SYS_NAND_ECCSIZE		512
135 #define CONFIG_SYS_NAND_ECCBYTES	26
136 #define CONFIG_SYS_NAND_ECCSTEPS	8
137 #define	CONFIG_SYS_NAND_ECCTOTAL	(CONFIG_SYS_NAND_ECCBYTES * \
138 						CONFIG_SYS_NAND_ECCSTEPS)
139 #define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH16_CODE_HW
140 /* END NAND Configuration. */
141 
142 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
143 /* #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000 */
144 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x200000
145 
146 /* Size must be a multiple of Nand erase size (524288 b) */
147 #define CONFIG_ENV_OFFSET		0x260000 /* environment starts here */
148 #define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
149 /* NAND: SPL falcon mode configs */
150 #ifdef CONFIG_SPL_OS_BOOT
151 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS	0x280000
152 #endif
153 
154 /*
155  * USB configuration.  We enable MUSB support, both for host and for
156  * gadget.  We set USB0 as peripheral and USB1 as host, based on the
157  * board schematic and physical port wired to each.  Then for host we
158  * add mass storage support.
159  */
160 #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT
161 #define CONFIG_AM335X_USB0
162 #define CONFIG_AM335X_USB0_MODE	MUSB_PERIPHERAL
163 #define CONFIG_AM335X_USB1
164 #define CONFIG_AM335X_USB1_MODE MUSB_HOST
165 
166 /* Network */
167 #define CONFIG_PHY_RESET	1
168 #define CONFIG_PHY_NATSEMI
169 #define CONFIG_PHY_REALTEK
170 
171 #endif	/* ! __CONFIG_PENGWYN_H */
172