1 /* 2 * Copyright 2010-2011 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * QorIQ RDB boards configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #ifdef CONFIG_36BIT 14 #define CONFIG_PHYS_64BIT 15 #endif 16 17 #if defined(CONFIG_P1020MBG) 18 #define CONFIG_BOARDNAME "P1020MBG-PC" 19 #define CONFIG_P1020 20 #define CONFIG_VSC7385_ENET 21 #define CONFIG_SLIC 22 #define __SW_BOOT_MASK 0x03 23 #define __SW_BOOT_NOR 0xe4 24 #define __SW_BOOT_SD 0x54 25 #define CONFIG_SYS_L2_SIZE (256 << 10) 26 #endif 27 28 #if defined(CONFIG_P1020UTM) 29 #define CONFIG_BOARDNAME "P1020UTM-PC" 30 #define CONFIG_P1020 31 #define __SW_BOOT_MASK 0x03 32 #define __SW_BOOT_NOR 0xe0 33 #define __SW_BOOT_SD 0x50 34 #define CONFIG_SYS_L2_SIZE (256 << 10) 35 #endif 36 37 #if defined(CONFIG_P1020RDB) 38 #define CONFIG_BOARDNAME "P1020RDB-PC" 39 #define CONFIG_NAND_FSL_ELBC 40 #define CONFIG_P1020 41 #define CONFIG_SPI_FLASH 42 #define CONFIG_VSC7385_ENET 43 #define CONFIG_SLIC 44 #define __SW_BOOT_MASK 0x03 45 #define __SW_BOOT_NOR 0x5c 46 #define __SW_BOOT_SPI 0x1c 47 #define __SW_BOOT_SD 0x9c 48 #define __SW_BOOT_NAND 0xec 49 #define __SW_BOOT_PCIE 0x6c 50 #define CONFIG_SYS_L2_SIZE (256 << 10) 51 #endif 52 53 #if defined(CONFIG_P1021RDB) 54 #define CONFIG_BOARDNAME "P1021RDB-PC" 55 #define CONFIG_NAND_FSL_ELBC 56 #define CONFIG_P1021 57 #define CONFIG_QE 58 #define CONFIG_SPI_FLASH 59 #define CONFIG_VSC7385_ENET 60 #define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of 61 addresses in the LBC */ 62 #define __SW_BOOT_MASK 0x03 63 #define __SW_BOOT_NOR 0x5c 64 #define __SW_BOOT_SPI 0x1c 65 #define __SW_BOOT_SD 0x9c 66 #define __SW_BOOT_NAND 0xec 67 #define __SW_BOOT_PCIE 0x6c 68 #define CONFIG_SYS_L2_SIZE (256 << 10) 69 #endif 70 71 #if defined(CONFIG_P1024RDB) 72 #define CONFIG_BOARDNAME "P1024RDB" 73 #define CONFIG_NAND_FSL_ELBC 74 #define CONFIG_P1024 75 #define CONFIG_SLIC 76 #define CONFIG_SPI_FLASH 77 #define __SW_BOOT_MASK 0xf3 78 #define __SW_BOOT_NOR 0x00 79 #define __SW_BOOT_SPI 0x08 80 #define __SW_BOOT_SD 0x04 81 #define __SW_BOOT_NAND 0x0c 82 #define CONFIG_SYS_L2_SIZE (256 << 10) 83 #endif 84 85 #if defined(CONFIG_P1025RDB) 86 #define CONFIG_BOARDNAME "P1025RDB" 87 #define CONFIG_NAND_FSL_ELBC 88 #define CONFIG_P1025 89 #define CONFIG_QE 90 #define CONFIG_SLIC 91 #define CONFIG_SPI_FLASH 92 93 #define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of 94 addresses in the LBC */ 95 #define __SW_BOOT_MASK 0xf3 96 #define __SW_BOOT_NOR 0x00 97 #define __SW_BOOT_SPI 0x08 98 #define __SW_BOOT_SD 0x04 99 #define __SW_BOOT_NAND 0x0c 100 #define CONFIG_SYS_L2_SIZE (256 << 10) 101 #endif 102 103 #if defined(CONFIG_P2020RDB) 104 #define CONFIG_BOARDNAME "P2020RDB-PCA" 105 #define CONFIG_NAND_FSL_ELBC 106 #define CONFIG_P2020 107 #define CONFIG_SPI_FLASH 108 #define CONFIG_VSC7385_ENET 109 #define __SW_BOOT_MASK 0x03 110 #define __SW_BOOT_NOR 0xc8 111 #define __SW_BOOT_SPI 0x28 112 #define __SW_BOOT_SD 0x68 /* or 0x18 */ 113 #define __SW_BOOT_NAND 0xe8 114 #define __SW_BOOT_PCIE 0xa8 115 #define CONFIG_SYS_L2_SIZE (512 << 10) 116 #endif 117 118 #if CONFIG_SYS_L2_SIZE >= (512 << 10) 119 /* must be 32-bit */ 120 #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 121 #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR 122 #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) 123 #endif 124 125 #ifdef CONFIG_SDCARD 126 #define CONFIG_RAMBOOT_SDCARD 127 #define CONFIG_SYS_RAMBOOT 128 #define CONFIG_SYS_EXTRA_ENV_RELOC 129 #define CONFIG_SYS_TEXT_BASE 0x11000000 130 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 131 #endif 132 133 #ifdef CONFIG_SPIFLASH 134 #define CONFIG_RAMBOOT_SPIFLASH 135 #define CONFIG_SYS_RAMBOOT 136 #define CONFIG_SYS_EXTRA_ENV_RELOC 137 #define CONFIG_SYS_TEXT_BASE 0x11000000 138 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 139 #endif 140 141 #ifdef CONFIG_NAND 142 #define CONFIG_SPL 143 #define CONFIG_SPL_INIT_MINIMAL 144 #define CONFIG_SPL_SERIAL_SUPPORT 145 #define CONFIG_SPL_NAND_SUPPORT 146 #define CONFIG_SPL_NAND_MINIMAL 147 #define CONFIG_SPL_FLUSH_IMAGE 148 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 149 150 #define CONFIG_SPL_TEXT_BASE 0xfffff000 151 #define CONFIG_SPL_MAX_SIZE 4096 152 153 #ifdef CONFIG_SYS_INIT_L2_ADDR 154 /* We multiply CONFIG_SPL_MAX_SIZE by two to leave some room for BSS. */ 155 #define CONFIG_SYS_TEXT_BASE 0xf8f82000 156 #define CONFIG_SPL_RELOC_TEXT_BASE \ 157 (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2) 158 #define CONFIG_SPL_RELOC_STACK \ 159 (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2) 160 #define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) 161 #define CONFIG_SYS_NAND_U_BOOT_START \ 162 (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SPL_MAX_SIZE) 163 #else 164 #define CONFIG_SYS_TEXT_BASE 0x00201000 165 #define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 166 #define CONFIG_SPL_RELOC_STACK 0x00100000 167 #define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) 168 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 169 #endif 170 171 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) 172 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0 173 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 174 #endif 175 176 #ifndef CONFIG_SYS_TEXT_BASE 177 #define CONFIG_SYS_TEXT_BASE 0xeff80000 178 #endif 179 180 #ifndef CONFIG_RESET_VECTOR_ADDRESS 181 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 182 #endif 183 184 #ifndef CONFIG_SYS_MONITOR_BASE 185 #ifdef CONFIG_SPL_BUILD 186 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 187 #else 188 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 189 #endif 190 #endif 191 192 /* High Level Configuration Options */ 193 #define CONFIG_BOOKE 194 #define CONFIG_E500 195 #define CONFIG_MPC85xx 196 197 #define CONFIG_MP 198 199 #define CONFIG_FSL_ELBC 200 #define CONFIG_PCI 201 #define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ 202 #define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ 203 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 204 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 205 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 206 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 207 208 #define CONFIG_FSL_LAW 209 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 210 #define CONFIG_ENV_OVERWRITE 211 212 #define CONFIG_CMD_SATA 213 #define CONFIG_SATA_SIL 214 #define CONFIG_SYS_SATA_MAX_DEVICE 2 215 #define CONFIG_LIBATA 216 #define CONFIG_LBA48 217 218 #if defined(CONFIG_P2020RDB) 219 #define CONFIG_SYS_CLK_FREQ 100000000 220 #else 221 #define CONFIG_SYS_CLK_FREQ 66666666 222 #endif 223 #define CONFIG_DDR_CLK_FREQ 66666666 224 225 #define CONFIG_HWCONFIG 226 /* 227 * These can be toggled for performance analysis, otherwise use default. 228 */ 229 #define CONFIG_L2_CACHE 230 #define CONFIG_BTB 231 232 #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ 233 234 #define CONFIG_ENABLE_36BIT_PHYS 235 236 #ifdef CONFIG_PHYS_64BIT 237 #define CONFIG_ADDR_MAP 1 238 #define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ 239 #endif 240 241 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 242 #define CONFIG_SYS_MEMTEST_END 0x1fffffff 243 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 244 245 #define CONFIG_SYS_CCSRBAR 0xffe00000 246 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 247 248 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k 249 SPL code*/ 250 #ifdef CONFIG_SPL_BUILD 251 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 252 #endif 253 254 /* DDR Setup */ 255 #define CONFIG_FSL_DDR3 256 #define CONFIG_SYS_DDR_RAW_TIMING 257 #define CONFIG_DDR_SPD 258 #define CONFIG_SYS_SPD_BUS_NUM 1 259 #define SPD_EEPROM_ADDRESS 0x52 260 #undef CONFIG_FSL_DDR_INTERACTIVE 261 262 #ifdef CONFIG_P1020MBG 263 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_2G 264 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 265 #else 266 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_1G 267 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 268 #endif 269 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) 270 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 271 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 272 273 #define CONFIG_NUM_DDR_CONTROLLERS 1 274 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 275 276 /* Default settings for DDR3 */ 277 #ifndef CONFIG_P2020RDB 278 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f 279 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 280 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 281 #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f 282 #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 283 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 284 285 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 286 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 287 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 288 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 289 290 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 291 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 292 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 293 #define CONFIG_SYS_DDR_RCW_1 0x00000000 294 #define CONFIG_SYS_DDR_RCW_2 0x00000000 295 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ 296 #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 297 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 298 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 299 300 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 301 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 302 #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 303 #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF 304 #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 305 #define CONFIG_SYS_DDR_MODE_1 0x40461520 306 #define CONFIG_SYS_DDR_MODE_2 0x8000c000 307 #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 308 #endif 309 310 #undef CONFIG_CLOCKS_IN_MHZ 311 312 /* 313 * Memory map 314 * 315 * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable 316 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3) 317 * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 318 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 512K cacheable 319 * (early boot only) 320 * 0xff80_0000 0xff80_7fff NAND flash 32K non-cacheable CS1/0 321 * 0xff98_0000 0xff98_ffff PMC 64K non-cacheable CS2 322 * 0xffa0_0000 0xffaf_ffff CPLD 1M non-cacheable CS3 323 * 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable CS2 324 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable 325 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable 326 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 327 */ 328 329 330 /* 331 * Local Bus Definitions 332 */ 333 #if defined(CONFIG_P1020MBG) 334 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ 335 #define CONFIG_SYS_FLASH_BASE 0xec000000 336 #elif defined(CONFIG_P1020UTM) 337 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* 32M */ 338 #define CONFIG_SYS_FLASH_BASE 0xee000000 339 #else 340 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* 16M */ 341 #define CONFIG_SYS_FLASH_BASE 0xef000000 342 #endif 343 344 345 #ifdef CONFIG_PHYS_64BIT 346 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 347 #else 348 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 349 #endif 350 351 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 352 | BR_PS_16 | BR_V) 353 354 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 355 356 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 357 #define CONFIG_SYS_FLASH_QUIET_TEST 358 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 359 360 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 361 362 #undef CONFIG_SYS_FLASH_CHECKSUM 363 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 364 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 365 366 #define CONFIG_FLASH_CFI_DRIVER 367 #define CONFIG_SYS_FLASH_CFI 368 #define CONFIG_SYS_FLASH_EMPTY_INFO 369 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 370 371 /* Nand Flash */ 372 #ifdef CONFIG_NAND_FSL_ELBC 373 #define CONFIG_SYS_NAND_BASE 0xff800000 374 #ifdef CONFIG_PHYS_64BIT 375 #define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull 376 #else 377 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 378 #endif 379 380 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 381 #define CONFIG_SYS_MAX_NAND_DEVICE 1 382 #define CONFIG_MTD_NAND_VERIFY_WRITE 383 #define CONFIG_CMD_NAND 384 #define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) 385 386 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 387 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 388 | BR_PS_8 /* Port Size = 8 bit */ \ 389 | BR_MS_FCM /* MSEL = FCM */ \ 390 | BR_V) /* valid */ 391 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB /* small page */ \ 392 | OR_FCM_CSCT \ 393 | OR_FCM_CST \ 394 | OR_FCM_CHT \ 395 | OR_FCM_SCY_1 \ 396 | OR_FCM_TRLX \ 397 | OR_FCM_EHTR) 398 #endif /* CONFIG_NAND_FSL_ELBC */ 399 400 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 401 402 #define CONFIG_SYS_INIT_RAM_LOCK 403 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ 404 #ifdef CONFIG_PHYS_64BIT 405 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 406 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 407 /* The assembler doesn't like typecast */ 408 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 409 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 410 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 411 #else 412 /* Initial L1 address */ 413 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 414 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 415 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 416 #endif 417 /* Size of used area in RAM */ 418 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 419 420 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 421 GENERATED_GBL_DATA_SIZE) 422 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 423 424 #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ 425 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ 426 427 #define CONFIG_SYS_CPLD_BASE 0xffa00000 428 #ifdef CONFIG_PHYS_64BIT 429 #define CONFIG_SYS_CPLD_BASE_PHYS 0xfffa00000ull 430 #else 431 #define CONFIG_SYS_CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE 432 #endif 433 /* CPLD config size: 1Mb */ 434 #define CONFIG_CPLD_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) | \ 435 BR_PS_8 | BR_V) 436 #define CONFIG_CPLD_OR_PRELIM (0xfff009f7) 437 438 #define CONFIG_SYS_PMC_BASE 0xff980000 439 #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE 440 #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ 441 BR_PS_8 | BR_V) 442 #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ 443 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ 444 OR_GPCM_EAD) 445 446 #ifdef CONFIG_NAND 447 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ 448 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 449 #define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 450 #define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 451 #else 452 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 453 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 454 #ifdef CONFIG_NAND_FSL_ELBC 455 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ 456 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 457 #endif 458 #endif 459 #define CONFIG_SYS_BR3_PRELIM CONFIG_CPLD_BR_PRELIM /* CPLD Base Address */ 460 #define CONFIG_SYS_OR3_PRELIM CONFIG_CPLD_OR_PRELIM /* CPLD Options */ 461 462 463 /* Vsc7385 switch */ 464 #ifdef CONFIG_VSC7385_ENET 465 #define CONFIG_SYS_VSC7385_BASE 0xffb00000 466 467 #ifdef CONFIG_PHYS_64BIT 468 #define CONFIG_SYS_VSC7385_BASE_PHYS 0xfffb00000ull 469 #else 470 #define CONFIG_SYS_VSC7385_BASE_PHYS CONFIG_SYS_VSC7385_BASE 471 #endif 472 473 #define CONFIG_SYS_VSC7385_BR_PRELIM \ 474 (BR_PHYS_ADDR(CONFIG_SYS_VSC7385_BASE_PHYS) | BR_PS_8 | BR_V) 475 #define CONFIG_SYS_VSC7385_OR_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | \ 476 OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_SETA | \ 477 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) 478 479 #define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_VSC7385_BR_PRELIM 480 #define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_VSC7385_OR_PRELIM 481 482 /* The size of the VSC7385 firmware image */ 483 #define CONFIG_VSC7385_IMAGE_SIZE 8192 484 #endif 485 486 /* Serial Port - controlled on board with jumper J8 487 * open - index 2 488 * shorted - index 1 489 */ 490 #define CONFIG_CONS_INDEX 1 491 #undef CONFIG_SERIAL_SOFTWARE_FIFO 492 #define CONFIG_SYS_NS16550 493 #define CONFIG_SYS_NS16550_SERIAL 494 #define CONFIG_SYS_NS16550_REG_SIZE 1 495 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 496 #ifdef CONFIG_SPL_BUILD 497 #define CONFIG_NS16550_MIN_FUNCTIONS 498 #endif 499 500 #define CONFIG_SYS_BAUDRATE_TABLE \ 501 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 502 503 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 504 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 505 506 /* Use the HUSH parser */ 507 #define CONFIG_SYS_HUSH_PARSER 508 509 /* 510 * Pass open firmware flat tree 511 */ 512 #define CONFIG_OF_LIBFDT 513 #define CONFIG_OF_BOARD_SETUP 514 #define CONFIG_OF_STDOUT_VIA_ALIAS 515 516 /* new uImage format support */ 517 #define CONFIG_FIT 518 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 519 520 /* I2C */ 521 #define CONFIG_SYS_I2C 522 #define CONFIG_SYS_I2C_FSL 523 #define CONFIG_SYS_FSL_I2C_SPEED 400000 524 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 525 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 526 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 527 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 528 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 529 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } 530 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 531 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ 532 533 /* 534 * I2C2 EEPROM 535 */ 536 #undef CONFIG_ID_EEPROM 537 538 #define CONFIG_RTC_PT7C4338 539 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 540 #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 541 542 /* enable read and write access to EEPROM */ 543 #define CONFIG_CMD_EEPROM 544 #define CONFIG_SYS_I2C_MULTI_EEPROMS 545 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 546 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 547 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 548 549 /* 550 * eSPI - Enhanced SPI 551 */ 552 #define CONFIG_HARD_SPI 553 #define CONFIG_FSL_ESPI 554 555 #if defined(CONFIG_SPI_FLASH) 556 #define CONFIG_SPI_FLASH_SPANSION 557 #define CONFIG_CMD_SF 558 #define CONFIG_SF_DEFAULT_SPEED 10000000 559 #define CONFIG_SF_DEFAULT_MODE 0 560 #endif 561 562 #if defined(CONFIG_PCI) 563 /* 564 * General PCI 565 * Memory space is mapped 1-1, but I/O space must start from 0. 566 */ 567 568 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 569 #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT" 570 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 571 #ifdef CONFIG_PHYS_64BIT 572 #define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 573 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 574 #else 575 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 576 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 577 #endif 578 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 579 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 580 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 581 #ifdef CONFIG_PHYS_64BIT 582 #define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull 583 #else 584 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 585 #endif 586 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 587 588 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 589 #define CONFIG_SYS_PCIE1_NAME "mini PCIe SLOT" 590 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 591 #ifdef CONFIG_PHYS_64BIT 592 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 593 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 594 #else 595 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 596 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 597 #endif 598 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 599 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 600 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 601 #ifdef CONFIG_PHYS_64BIT 602 #define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull 603 #else 604 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 605 #endif 606 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 607 608 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 609 #define CONFIG_E1000 /* Defind e1000 pci Ethernet card*/ 610 #define CONFIG_CMD_PCI 611 #define CONFIG_CMD_NET 612 613 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 614 #define CONFIG_DOS_PARTITION 615 #endif /* CONFIG_PCI */ 616 617 #if defined(CONFIG_TSEC_ENET) 618 #define CONFIG_MII /* MII PHY management */ 619 #define CONFIG_TSEC1 620 #define CONFIG_TSEC1_NAME "eTSEC1" 621 #define CONFIG_TSEC2 622 #define CONFIG_TSEC2_NAME "eTSEC2" 623 #define CONFIG_TSEC3 624 #define CONFIG_TSEC3_NAME "eTSEC3" 625 626 #define TSEC1_PHY_ADDR 2 627 #define TSEC2_PHY_ADDR 0 628 #define TSEC3_PHY_ADDR 1 629 630 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 631 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 632 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 633 634 #define TSEC1_PHYIDX 0 635 #define TSEC2_PHYIDX 0 636 #define TSEC3_PHYIDX 0 637 638 #define CONFIG_ETHPRIME "eTSEC1" 639 640 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 641 642 #define CONFIG_HAS_ETH0 643 #define CONFIG_HAS_ETH1 644 #define CONFIG_HAS_ETH2 645 #endif /* CONFIG_TSEC_ENET */ 646 647 #ifdef CONFIG_QE 648 /* QE microcode/firmware address */ 649 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 650 #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xefec0000 651 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 652 #endif /* CONFIG_QE */ 653 654 #ifdef CONFIG_P1025RDB 655 /* 656 * QE UEC ethernet configuration 657 */ 658 #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) 659 660 #undef CONFIG_UEC_ETH 661 #define CONFIG_PHY_MODE_NEED_CHANGE 662 663 #define CONFIG_UEC_ETH1 /* ETH1 */ 664 #define CONFIG_HAS_ETH0 665 666 #ifdef CONFIG_UEC_ETH1 667 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 668 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */ 669 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */ 670 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 671 #define CONFIG_SYS_UEC1_PHY_ADDR 0x0 /* 0x0 for MII */ 672 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 673 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 674 #endif /* CONFIG_UEC_ETH1 */ 675 676 #define CONFIG_UEC_ETH5 /* ETH5 */ 677 #define CONFIG_HAS_ETH1 678 679 #ifdef CONFIG_UEC_ETH5 680 #define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */ 681 #define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE 682 #define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */ 683 #define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH 684 #define CONFIG_SYS_UEC5_PHY_ADDR 0x3 /* 0x3 for RMII */ 685 #define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 686 #define CONFIG_SYS_UEC5_INTERFACE_SPEED 100 687 #endif /* CONFIG_UEC_ETH5 */ 688 #endif /* CONFIG_P1025RDB */ 689 690 /* 691 * Environment 692 */ 693 #ifdef CONFIG_RAMBOOT_SPIFLASH 694 #define CONFIG_ENV_IS_IN_SPI_FLASH 695 #define CONFIG_ENV_SPI_BUS 0 696 #define CONFIG_ENV_SPI_CS 0 697 #define CONFIG_ENV_SPI_MAX_HZ 10000000 698 #define CONFIG_ENV_SPI_MODE 0 699 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 700 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 701 #define CONFIG_ENV_SECT_SIZE 0x10000 702 #elif defined(CONFIG_RAMBOOT_SDCARD) 703 #define CONFIG_ENV_IS_IN_MMC 704 #define CONFIG_FSL_FIXED_MMC_LOCATION 705 #define CONFIG_ENV_SIZE 0x2000 706 #define CONFIG_SYS_MMC_ENV_DEV 0 707 #elif defined(CONFIG_NAND) 708 #define CONFIG_ENV_IS_IN_NAND 709 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 710 #define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) 711 #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) 712 #elif defined(CONFIG_SYS_RAMBOOT) 713 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ 714 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 715 #define CONFIG_ENV_SIZE 0x2000 716 #else 717 #define CONFIG_ENV_IS_IN_FLASH 718 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 719 #define CONFIG_ENV_ADDR 0xfff80000 720 #else 721 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 722 #endif 723 #define CONFIG_ENV_SIZE 0x2000 724 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 725 #endif 726 727 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 728 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 729 730 /* 731 * Command line configuration. 732 */ 733 #include <config_cmd_default.h> 734 735 #define CONFIG_CMD_IRQ 736 #define CONFIG_CMD_PING 737 #define CONFIG_CMD_I2C 738 #define CONFIG_CMD_MII 739 #define CONFIG_CMD_DATE 740 #define CONFIG_CMD_ELF 741 #define CONFIG_CMD_SETEXPR 742 #define CONFIG_CMD_REGINFO 743 744 /* 745 * USB 746 */ 747 #define CONFIG_HAS_FSL_DR_USB 748 749 #if defined(CONFIG_HAS_FSL_DR_USB) 750 #define CONFIG_USB_EHCI 751 752 #ifdef CONFIG_USB_EHCI 753 #define CONFIG_CMD_USB 754 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 755 #define CONFIG_USB_EHCI_FSL 756 #define CONFIG_USB_STORAGE 757 #endif 758 #endif 759 760 #define CONFIG_MMC 761 762 #ifdef CONFIG_MMC 763 #define CONFIG_FSL_ESDHC 764 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 765 #define CONFIG_CMD_MMC 766 #define CONFIG_GENERIC_MMC 767 #endif 768 769 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \ 770 || defined(CONFIG_FSL_SATA) 771 #define CONFIG_CMD_EXT2 772 #define CONFIG_CMD_FAT 773 #define CONFIG_DOS_PARTITION 774 #endif 775 776 #undef CONFIG_WATCHDOG /* watchdog disabled */ 777 778 /* 779 * Miscellaneous configurable options 780 */ 781 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 782 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 783 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 784 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 785 #if defined(CONFIG_CMD_KGDB) 786 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 787 #else 788 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 789 #endif 790 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 791 /* Print Buffer Size */ 792 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 793 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 794 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ 795 796 /* 797 * For booting Linux, the board info and command line data 798 * have to be in the first 64 MB of memory, since this is 799 * the maximum mapped by the Linux kernel during initialization. 800 */ 801 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ 802 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 803 804 #if defined(CONFIG_CMD_KGDB) 805 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 806 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 807 #endif 808 809 /* 810 * Environment Configuration 811 */ 812 #define CONFIG_HOSTNAME unknown 813 #define CONFIG_ROOTPATH "/opt/nfsroot" 814 #define CONFIG_BOOTFILE "uImage" 815 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 816 817 /* default location for tftp and bootm */ 818 #define CONFIG_LOADADDR 1000000 819 820 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 821 #define CONFIG_BOOTARGS /* the boot command will set bootargs */ 822 823 #define CONFIG_BAUDRATE 115200 824 825 #ifdef __SW_BOOT_NOR 826 #define __NOR_RST_CMD \ 827 norboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_NOR 1; \ 828 i2c mw 18 3 __SW_BOOT_MASK 1; reset 829 #endif 830 #ifdef __SW_BOOT_SPI 831 #define __SPI_RST_CMD \ 832 spiboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_SPI 1; \ 833 i2c mw 18 3 __SW_BOOT_MASK 1; reset 834 #endif 835 #ifdef __SW_BOOT_SD 836 #define __SD_RST_CMD \ 837 sdboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_SD 1; \ 838 i2c mw 18 3 __SW_BOOT_MASK 1; reset 839 #endif 840 #ifdef __SW_BOOT_NAND 841 #define __NAND_RST_CMD \ 842 nandboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_NAND 1; \ 843 i2c mw 18 3 __SW_BOOT_MASK 1; reset 844 #endif 845 #ifdef __SW_BOOT_PCIE 846 #define __PCIE_RST_CMD \ 847 pciboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_PCIE 1; \ 848 i2c mw 18 3 __SW_BOOT_MASK 1; reset 849 #endif 850 851 #define CONFIG_EXTRA_ENV_SETTINGS \ 852 "netdev=eth0\0" \ 853 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 854 "loadaddr=1000000\0" \ 855 "bootfile=uImage\0" \ 856 "tftpflash=tftpboot $loadaddr $uboot; " \ 857 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 858 "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 859 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \ 860 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 861 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ 862 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ 863 "consoledev=ttyS0\0" \ 864 "ramdiskaddr=2000000\0" \ 865 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 866 "fdtaddr=c00000\0" \ 867 "bdev=sda1\0" \ 868 "jffs2nor=mtdblock3\0" \ 869 "norbootaddr=ef080000\0" \ 870 "norfdtaddr=ef040000\0" \ 871 "jffs2nand=mtdblock9\0" \ 872 "nandbootaddr=100000\0" \ 873 "nandfdtaddr=80000\0" \ 874 "ramdisk_size=120000\0" \ 875 "map_lowernorbank=i2c dev 1; i2c mw 18 1 02 1; i2c mw 18 3 fd 1\0" \ 876 "map_uppernorbank=i2c dev 1; i2c mw 18 1 00 1; i2c mw 18 3 fd 1\0" \ 877 __stringify(__NOR_RST_CMD)"\0" \ 878 __stringify(__SPI_RST_CMD)"\0" \ 879 __stringify(__SD_RST_CMD)"\0" \ 880 __stringify(__NAND_RST_CMD)"\0" \ 881 __stringify(__PCIE_RST_CMD)"\0" 882 883 #define CONFIG_NFSBOOTCOMMAND \ 884 "setenv bootargs root=/dev/nfs rw " \ 885 "nfsroot=$serverip:$rootpath " \ 886 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 887 "console=$consoledev,$baudrate $othbootargs;" \ 888 "tftp $loadaddr $bootfile;" \ 889 "tftp $fdtaddr $fdtfile;" \ 890 "bootm $loadaddr - $fdtaddr" 891 892 #define CONFIG_HDBOOT \ 893 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ 894 "console=$consoledev,$baudrate $othbootargs;" \ 895 "usb start;" \ 896 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ 897 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ 898 "bootm $loadaddr - $fdtaddr" 899 900 #define CONFIG_USB_FAT_BOOT \ 901 "setenv bootargs root=/dev/ram rw " \ 902 "console=$consoledev,$baudrate $othbootargs " \ 903 "ramdisk_size=$ramdisk_size;" \ 904 "usb start;" \ 905 "fatload usb 0:2 $loadaddr $bootfile;" \ 906 "fatload usb 0:2 $fdtaddr $fdtfile;" \ 907 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ 908 "bootm $loadaddr $ramdiskaddr $fdtaddr" 909 910 #define CONFIG_USB_EXT2_BOOT \ 911 "setenv bootargs root=/dev/ram rw " \ 912 "console=$consoledev,$baudrate $othbootargs " \ 913 "ramdisk_size=$ramdisk_size;" \ 914 "usb start;" \ 915 "ext2load usb 0:4 $loadaddr $bootfile;" \ 916 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 917 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 918 "bootm $loadaddr $ramdiskaddr $fdtaddr" 919 920 #define CONFIG_NORBOOT \ 921 "setenv bootargs root=/dev/$jffs2nor rw " \ 922 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ 923 "bootm $norbootaddr - $norfdtaddr" 924 925 #define CONFIG_RAMBOOTCOMMAND \ 926 "setenv bootargs root=/dev/ram rw " \ 927 "console=$consoledev,$baudrate $othbootargs " \ 928 "ramdisk_size=$ramdisk_size;" \ 929 "tftp $ramdiskaddr $ramdiskfile;" \ 930 "tftp $loadaddr $bootfile;" \ 931 "tftp $fdtaddr $fdtfile;" \ 932 "bootm $loadaddr $ramdiskaddr $fdtaddr" 933 934 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 935 936 #endif /* __CONFIG_H */ 937