1 /* 2 * (C) Copyright 2006-2008 3 * Texas Instruments. 4 * Richard Woodruff <r-woodruff2@ti.com> 5 * Syed Mohammed Khasim <x0khasim@ti.com> 6 * 7 * Configuration settings for the TI OMAP3530 Beagle board. 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #ifndef __CONFIG_H 13 #define __CONFIG_H 14 15 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 16 17 #include <configs/ti_omap3_common.h> 18 19 /* 20 * We are only ever GP parts and will utilize all of the "downloaded image" 21 * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB). 22 */ 23 #undef CONFIG_SPL_TEXT_BASE 24 #define CONFIG_SPL_TEXT_BASE 0x40200000 25 26 #define CONFIG_SPL_FRAMEWORK 27 28 #define CONFIG_MISC_INIT_R 29 #define CONFIG_CMDLINE_TAG 30 #define CONFIG_SETUP_MEMORY_TAGS 31 #define CONFIG_INITRD_TAG 32 #define CONFIG_REVISION_TAG 33 34 /* NAND */ 35 #if defined(CONFIG_NAND) 36 #define CONFIG_SYS_FLASH_BASE NAND_BASE 37 #define CONFIG_SYS_MAX_NAND_DEVICE 1 38 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 39 #define CONFIG_SYS_NAND_PAGE_COUNT 64 40 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 41 #define CONFIG_SYS_NAND_OOBSIZE 64 42 #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) 43 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS 44 #define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ 45 10, 11, 12, 13} 46 #define CONFIG_SYS_NAND_ECCSIZE 512 47 #define CONFIG_SYS_NAND_ECCBYTES 3 48 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW 49 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 50 #define CONFIG_ENV_IS_IN_NAND 1 51 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ 52 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ 53 #define CONFIG_ENV_OFFSET 0x260000 54 #define CONFIG_ENV_ADDR 0x260000 55 #define CONFIG_ENV_OVERWRITE 56 #define CONFIG_MTD_PARTITIONS /* required for UBI partition support */ 57 /* NAND: SPL falcon mode configs */ 58 #if defined(CONFIG_SPL_OS_BOOT) 59 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000 60 #endif /* CONFIG_SPL_OS_BOOT */ 61 #endif /* CONFIG_NAND */ 62 63 /* MUSB */ 64 #define CONFIG_USB_OMAP3 65 #define CONFIG_USB_MUSB_OMAP2PLUS 66 #define CONFIG_USB_MUSB_PIO_ONLY 67 #define CONFIG_TWL4030_USB 68 69 /* USB EHCI */ 70 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147 71 72 /* Enable Multi Bus support for I2C */ 73 #define CONFIG_I2C_MULTI_BUS 74 75 /* DSS Support */ 76 #define CONFIG_VIDEO_OMAP3 77 78 /* TWL4030 LED Support */ 79 #define CONFIG_TWL4030_LED 80 81 #define BOOT_TARGET_DEVICES(func) \ 82 func(MMC, mmc, 0) 83 84 #define CONFIG_BOOTCOMMAND \ 85 "run findfdt; " \ 86 "run distro_bootcmd; " \ 87 "mmc dev ${mmcdev}; if mmc rescan; then " \ 88 "if run userbutton; then " \ 89 "setenv bootenv uEnv.txt;" \ 90 "else " \ 91 "setenv bootenv user.txt;" \ 92 "fi;" \ 93 "echo SD/MMC found on device ${mmcdev};" \ 94 "if run loadbootenv; then " \ 95 "echo Loaded environment from ${bootenv};" \ 96 "run importbootenv;" \ 97 "fi;" \ 98 "if test -n $uenvcmd; then " \ 99 "echo Running uenvcmd ...;" \ 100 "run uenvcmd;" \ 101 "fi;" \ 102 "if run loadbootscript; then " \ 103 "run bootscript; " \ 104 "else " \ 105 "if run loadimage; then " \ 106 "run loadfdt;" \ 107 "run mmcboot;" \ 108 "fi;" \ 109 "fi; " \ 110 "fi;" \ 111 "run nandboot;" \ 112 "setenv bootfile zImage;" \ 113 "if run loadimage; then " \ 114 "run loadfdt;" \ 115 "run mmcbootz; " \ 116 "fi; " \ 117 118 #include <config_distro_bootcmd.h> 119 120 #define CONFIG_EXTRA_ENV_SETTINGS \ 121 DEFAULT_LINUX_BOOT_ENV \ 122 "fdt_high=0xffffffff\0" \ 123 "usbtty=cdc_acm\0" \ 124 "bootfile=uImage\0" \ 125 "ramdisk=ramdisk.gz\0" \ 126 "bootdir=/boot\0" \ 127 "bootpart=0:2\0" \ 128 "console=ttyO2,115200n8\0" \ 129 "mpurate=auto\0" \ 130 "buddy=none\0" \ 131 "optargs=\0" \ 132 "camera=none\0" \ 133 "vram=12M\0" \ 134 "dvimode=640x480MR-16@60\0" \ 135 "defaultdisplay=dvi\0" \ 136 "mmcdev=0\0" \ 137 "mmcroot=/dev/mmcblk0p2 rw\0" \ 138 "mmcrootfstype=ext4 rootwait\0" \ 139 "nandroot=ubi0:rootfs ubi.mtd=4\0" \ 140 "nandrootfstype=ubifs\0" \ 141 "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \ 142 "ramrootfstype=ext2\0" \ 143 "mmcargs=setenv bootargs console=${console} " \ 144 "${optargs} " \ 145 "mpurate=${mpurate} " \ 146 "buddy=${buddy} "\ 147 "camera=${camera} "\ 148 "vram=${vram} " \ 149 "omapfb.mode=dvi:${dvimode} " \ 150 "omapdss.def_disp=${defaultdisplay} " \ 151 "root=${mmcroot} " \ 152 "rootfstype=${mmcrootfstype}\0" \ 153 "nandargs=setenv bootargs console=${console} " \ 154 "${optargs} " \ 155 "mpurate=${mpurate} " \ 156 "buddy=${buddy} "\ 157 "camera=${camera} "\ 158 "vram=${vram} " \ 159 "omapfb.mode=dvi:${dvimode} " \ 160 "omapdss.def_disp=${defaultdisplay} " \ 161 "root=${nandroot} " \ 162 "rootfstype=${nandrootfstype}\0" \ 163 "findfdt=" \ 164 "if test $beaglerev = AxBx; then " \ 165 "setenv fdtfile omap3-beagle.dtb; fi; " \ 166 "if test $beaglerev = Cx; then " \ 167 "setenv fdtfile omap3-beagle.dtb; fi; " \ 168 "if test $beaglerev = C4; then " \ 169 "setenv fdtfile omap3-beagle.dtb; fi; " \ 170 "if test $beaglerev = xMAB; then " \ 171 "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \ 172 "if test $beaglerev = xMC; then " \ 173 "setenv fdtfile omap3-beagle-xm.dtb; fi; " \ 174 "if test $fdtfile = undefined; then " \ 175 "echo WARNING: Could not determine device tree to use; fi; \0" \ 176 "validatefdt=" \ 177 "if test $beaglerev = xMAB; then " \ 178 "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \ 179 "setenv fdtfile omap3-beagle-xm.dtb; " \ 180 "fi; " \ 181 "fi; \0" \ 182 "bootenv=uEnv.txt\0" \ 183 "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ 184 "importbootenv=echo Importing environment from mmc ...; " \ 185 "env import -t -r $loadaddr $filesize\0" \ 186 "ramargs=setenv bootargs console=${console} " \ 187 "${optargs} " \ 188 "mpurate=${mpurate} " \ 189 "buddy=${buddy} "\ 190 "vram=${vram} " \ 191 "omapfb.mode=dvi:${dvimode} " \ 192 "omapdss.def_disp=${defaultdisplay} " \ 193 "root=${ramroot} " \ 194 "rootfstype=${ramrootfstype}\0" \ 195 "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \ 196 "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ 197 "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 198 "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \ 199 "source ${loadaddr}\0" \ 200 "loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ 201 "mmcboot=echo Booting ${bootfile} with DT from mmc${mmcdev} ...; " \ 202 "run mmcargs; " \ 203 "bootm ${loadaddr} - ${fdtaddr}\0" \ 204 "mmcbootz=echo Booting ${bootfile} with DT from mmc${mmcdev} ...; " \ 205 "run mmcargs; " \ 206 "bootz ${loadaddr} - ${fdtaddr}\0" \ 207 "nandboot=echo Booting from nand ...; " \ 208 "run nandargs; " \ 209 "nand read ${loadaddr} 280000 400000; " \ 210 "bootm ${loadaddr}\0" \ 211 "ramboot=echo Booting from ramdisk ...; " \ 212 "run ramargs; " \ 213 "bootm ${loadaddr}\0" \ 214 "userbutton=if gpio input 173; then run userbutton_xm; " \ 215 "else run userbutton_nonxm; fi;\0" \ 216 "userbutton_xm=gpio input 4;\0" \ 217 "userbutton_nonxm=gpio input 7;\0" \ 218 BOOTENV 219 220 #endif /* __CONFIG_H */ 221