1 /*
2  * Copyright 2014 Freescale Semiconductor, Inc.
3  *
4  * Configuration settings for the Freescale i.MX6SX Sabreauto board.
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 #ifndef __CONFIG_H
10 #define __CONFIG_H
11 
12 #include "mx6_common.h"
13 
14 /* Size of malloc() pool */
15 #define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
16 
17 #define CONFIG_MXC_UART
18 #define CONFIG_MXC_UART_BASE		UART1_BASE
19 
20 #define CONFIG_EXTRA_ENV_SETTINGS \
21 	"script=boot.scr\0" \
22 	"image=zImage\0" \
23 	"console=ttymxc0\0" \
24 	"fdt_high=0xffffffff\0" \
25 	"initrd_high=0xffffffff\0" \
26 	"fdt_file=imx6sx-sabreauto.dtb\0" \
27 	"fdt_addr=0x88000000\0" \
28 	"boot_fdt=try\0" \
29 	"ip_dyn=yes\0" \
30 	"mmcdev=0\0" \
31 	"mmcpart=1\0" \
32 	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
33 	"mmcargs=setenv bootargs console=${console},${baudrate} " \
34 		"root=${mmcroot}\0" \
35 	"loadbootscript=" \
36 		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
37 	"bootscript=echo Running bootscript from mmc ...; " \
38 		"source\0" \
39 	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
40 	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
41 	"mmcboot=echo Booting from mmc ...; " \
42 		"run mmcargs; " \
43 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
44 			"if run loadfdt; then " \
45 				"bootz ${loadaddr} - ${fdt_addr}; " \
46 			"else " \
47 				"if test ${boot_fdt} = try; then " \
48 					"bootz; " \
49 				"else " \
50 					"echo WARN: Cannot load the DT; " \
51 				"fi; " \
52 			"fi; " \
53 		"else " \
54 			"bootz; " \
55 		"fi;\0" \
56 	"netargs=setenv bootargs console=${console},${baudrate} " \
57 		"root=/dev/nfs " \
58 	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
59 		"netboot=echo Booting from net ...; " \
60 		"run netargs; " \
61 		"if test ${ip_dyn} = yes; then " \
62 			"setenv get_cmd dhcp; " \
63 		"else " \
64 			"setenv get_cmd tftp; " \
65 		"fi; " \
66 		"${get_cmd} ${image}; " \
67 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
68 			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
69 				"bootz ${loadaddr} - ${fdt_addr}; " \
70 			"else " \
71 				"if test ${boot_fdt} = try; then " \
72 					"bootz; " \
73 				"else " \
74 					"echo WARN: Cannot load the DT; " \
75 				"fi; " \
76 			"fi; " \
77 		"else " \
78 			"bootz; " \
79 		"fi;\0"
80 
81 #define CONFIG_BOOTCOMMAND \
82 	   "mmc dev ${mmcdev};" \
83 	   "mmc dev ${mmcdev}; if mmc rescan; then " \
84 		   "if run loadbootscript; then " \
85 			   "run bootscript; " \
86 		   "else " \
87 			   "if run loadimage; then " \
88 				   "run mmcboot; " \
89 			   "else run netboot; " \
90 			   "fi; " \
91 		   "fi; " \
92 	   "else run netboot; fi"
93 
94 /* Miscellaneous configurable options */
95 #define CONFIG_SYS_MEMTEST_START	0x80000000
96 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
97 
98 /* Physical Memory Map */
99 #define CONFIG_NR_DRAM_BANKS		1
100 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
101 
102 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
103 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
104 #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
105 
106 #define CONFIG_SYS_INIT_SP_OFFSET \
107 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
108 #define CONFIG_SYS_INIT_SP_ADDR \
109 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
110 
111 /* MMC Configuration */
112 #define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC3_BASE_ADDR
113 
114 /* I2C Configs */
115 #define CONFIG_SYS_I2C_MXC
116 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
117 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
118 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
119 #define CONFIG_SYS_I2C_SPEED		  100000
120 
121 /* NAND flash command */
122 #define CONFIG_CMD_NAND
123 #define CONFIG_CMD_NAND_TRIMFFS
124 
125 /* NAND stuff */
126 #define CONFIG_NAND_MXS
127 #define CONFIG_SYS_MAX_NAND_DEVICE     1
128 #define CONFIG_SYS_NAND_BASE           0x40000000
129 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
130 #define CONFIG_SYS_NAND_ONFI_DETECTION
131 
132 /* DMA stuff, needed for GPMI/MXS NAND support */
133 #define CONFIG_APBH_DMA
134 #define CONFIG_APBH_DMA_BURST
135 #define CONFIG_APBH_DMA_BURST8
136 
137 /* Network */
138 
139 #define CONFIG_FEC_MXC
140 #define CONFIG_MII
141 
142 #define IMX_FEC_BASE			ENET2_BASE_ADDR
143 #define CONFIG_FEC_MXC_PHYADDR          0x0
144 
145 #define CONFIG_FEC_XCV_TYPE             RGMII
146 #define CONFIG_ETHPRIME                 "FEC"
147 
148 #define CONFIG_PHYLIB
149 #define CONFIG_PHY_ATHEROS
150 
151 #ifdef CONFIG_CMD_USB
152 #define CONFIG_USB_EHCI
153 #define CONFIG_USB_EHCI_MX6
154 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
155 #define CONFIG_USB_HOST_ETHER
156 #define CONFIG_USB_ETHER_ASIX
157 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
158 #define CONFIG_MXC_USB_FLAGS   0
159 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
160 #endif
161 
162 #define CONFIG_IMX_THERMAL
163 
164 #ifdef CONFIG_FSL_QSPI
165 #define CONFIG_SYS_FSL_QSPI_AHB
166 #define CONFIG_SF_DEFAULT_BUS		0
167 #define CONFIG_SF_DEFAULT_CS		0
168 #define CONFIG_SF_DEFAULT_SPEED	40000000
169 #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
170 #define FSL_QSPI_FLASH_SIZE		SZ_32M
171 #define FSL_QSPI_FLASH_NUM		2
172 #endif
173 
174 #define CONFIG_ENV_OFFSET		(8 * SZ_64K)
175 #define CONFIG_ENV_SIZE			SZ_8K
176 #define CONFIG_ENV_IS_IN_MMC
177 
178 #define CONFIG_SYS_FSL_USDHC_NUM	2
179 #if defined(CONFIG_ENV_IS_IN_MMC)
180 #define CONFIG_SYS_MMC_ENV_DEV		0  /*USDHC3*/
181 #endif
182 
183 #endif				/* __CONFIG_H */
184