1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2012 Freescale Semiconductor, Inc. 4 * 5 * Configuration settings for the Freescale i.MX6Q SabreAuto board. 6 */ 7 8 #ifndef __MX6SABREAUTO_CONFIG_H 9 #define __MX6SABREAUTO_CONFIG_H 10 11 #ifdef CONFIG_SPL 12 #include "imx6_spl.h" 13 #endif 14 15 #define CONFIG_MACH_TYPE 3529 16 #define CONFIG_MXC_UART_BASE UART4_BASE 17 #define CONSOLE_DEV "ttymxc3" 18 19 /* USB Configs */ 20 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 21 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ 22 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 23 #define CONFIG_MXC_USB_FLAGS 0 24 25 #define CONFIG_PCA953X 26 #define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} } 27 28 #include "mx6sabre_common.h" 29 30 /* Falcon Mode */ 31 #ifdef CONFIG_SPL_OS_BOOT 32 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" 33 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 34 #define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000 35 36 /* Falcon Mode - MMC support: args@1MB kernel@2MB */ 37 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 /* 1MB */ 38 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512) 39 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */ 40 #endif 41 42 #ifdef CONFIG_MTD_NOR_FLASH 43 #define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR 44 #define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024) 45 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 46 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ 47 #define CONFIG_SYS_FLASH_EMPTY_INFO 48 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 49 #endif 50 51 #define CONFIG_SYS_FSL_USDHC_NUM 2 52 #if defined(CONFIG_ENV_IS_IN_MMC) 53 #define CONFIG_SYS_MMC_ENV_DEV 0 54 #endif 55 56 /* I2C Configs */ 57 #define CONFIG_SYS_I2C 58 #define CONFIG_SYS_I2C_MXC 59 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 60 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 61 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 62 #define CONFIG_SYS_I2C_SPEED 100000 63 64 /* NAND stuff */ 65 #define CONFIG_SYS_MAX_NAND_DEVICE 1 66 #define CONFIG_SYS_NAND_BASE 0x40000000 67 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 68 #define CONFIG_SYS_NAND_ONFI_DETECTION 69 70 /* DMA stuff, needed for GPMI/MXS NAND support */ 71 72 /* PMIC */ 73 #define CONFIG_POWER 74 #define CONFIG_POWER_I2C 75 #define CONFIG_POWER_PFUZE100 76 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 77 78 #endif /* __MX6SABREAUTO_CONFIG_H */ 79