1 /* 2 * (C) Copyright 2010, Stefano Babic <sbabic@denx.de> 3 * 4 * (C) Copyright 2008-2010 Freescale Semiconductor, Inc. 5 * 6 * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de> 7 * 8 * Configuration for the MX35pdk Freescale board. 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 #include <asm/arch/imx-regs.h> 17 18 /* High Level Configuration Options */ 19 #define CONFIG_MX35 20 21 #define CONFIG_SYS_FSL_CLK 22 23 /* Set TEXT at the beginning of the NOR flash */ 24 25 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 26 #define CONFIG_REVISION_TAG 27 #define CONFIG_SETUP_MEMORY_TAGS 28 #define CONFIG_INITRD_TAG 29 30 /* 31 * Size of malloc() pool 32 */ 33 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) 34 35 /* 36 * Hardware drivers 37 */ 38 #define CONFIG_SYS_I2C 39 #define CONFIG_SYS_I2C_MXC 40 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 41 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 42 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 43 44 /* 45 * PMIC Configs 46 */ 47 #define CONFIG_POWER 48 #define CONFIG_POWER_I2C 49 #define CONFIG_POWER_FSL 50 #define CONFIG_POWER_FSL_MC13892 51 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x08 52 #define CONFIG_RTC_MC13XXX 53 54 /* 55 * MFD MC9SDZ60 56 */ 57 #define CONFIG_FSL_MC9SDZ60 58 #define CONFIG_SYS_FSL_MC9SDZ60_I2C_ADDR 0x69 59 60 /* 61 * UART (console) 62 */ 63 #define CONFIG_MXC_UART 64 #define CONFIG_MXC_UART_BASE UART1_BASE 65 66 /* allow to overwrite serial and ethaddr */ 67 #define CONFIG_ENV_OVERWRITE 68 69 /* 70 * Command definition 71 */ 72 73 #define CONFIG_NET_RETRY_COUNT 100 74 75 76 #define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */ 77 78 /* 79 * Ethernet on the debug board (SMC911) 80 */ 81 #define CONFIG_HAS_ETH1 82 #define CONFIG_ETHPRIME 83 84 /* 85 * Ethernet on SOC (FEC) 86 */ 87 #define CONFIG_FEC_MXC 88 #define IMX_FEC_BASE FEC_BASE_ADDR 89 #define CONFIG_FEC_MXC_PHYADDR 0x1F 90 91 #define CONFIG_MII 92 93 #define CONFIG_ARP_TIMEOUT 200UL 94 95 /* 96 * Miscellaneous configurable options 97 */ 98 99 #define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */ 100 #define CONFIG_SYS_MEMTEST_END 0x10000 101 102 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 103 104 /* 105 * Physical Memory Map 106 */ 107 #define CONFIG_NR_DRAM_BANKS 2 108 #define PHYS_SDRAM_1 CSD0_BASE_ADDR 109 #define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024) 110 #define PHYS_SDRAM_2 CSD1_BASE_ADDR 111 #define PHYS_SDRAM_2_SIZE (128 * 1024 * 1024) 112 113 #define CONFIG_SYS_SDRAM_BASE CSD0_BASE_ADDR 114 #define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR + 0x10000) 115 #define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE / 2) 116 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 117 GENERATED_GBL_DATA_SIZE) 118 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 119 CONFIG_SYS_GBL_DATA_OFFSET) 120 121 /* 122 * MTD Command for mtdparts 123 */ 124 #define CONFIG_MTD_DEVICE 125 #define CONFIG_FLASH_CFI_MTD 126 #define CONFIG_MTD_PARTITIONS 127 128 /* 129 * FLASH and environment organization 130 */ 131 #define CONFIG_SYS_FLASH_BASE CS0_BASE_ADDR 132 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 133 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ 134 /* Monitor at beginning of flash */ 135 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 136 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) 137 138 #define CONFIG_ENV_SECT_SIZE (128 * 1024) 139 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 140 141 /* Address and size of Redundant Environment Sector */ 142 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) 143 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 144 145 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 146 CONFIG_SYS_MONITOR_LEN) 147 148 #if defined(CONFIG_FSL_ENV_IN_NAND) 149 #define CONFIG_ENV_OFFSET (1024 * 1024) 150 #endif 151 152 /* 153 * CFI FLASH driver setup 154 */ 155 #define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */ 156 #define CONFIG_FLASH_CFI_DRIVER 157 158 /* A non-standard buffered write algorithm */ 159 #define CONFIG_FLASH_SPANSION_S29WS_N 160 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* faster */ 161 #define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */ 162 163 /* 164 * NAND FLASH driver setup 165 */ 166 #define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR) 167 #define CONFIG_SYS_MAX_NAND_DEVICE 1 168 #define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR) 169 #define CONFIG_MXC_NAND_HWECC 170 #define CONFIG_SYS_NAND_LARGEPAGE 171 172 /* EHCI driver */ 173 #define CONFIG_EHCI_IS_TDI 174 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 175 #define CONFIG_USB_EHCI_MXC 176 #define CONFIG_MXC_USB_PORT 0 177 #define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERFACE_DIFF_UNI | \ 178 MXC_EHCI_POWER_PINS_ENABLED | \ 179 MXC_EHCI_OC_PIN_ACTIVE_LOW) 180 #define CONFIG_MXC_USB_PORTSC (MXC_EHCI_UTMI_16BIT | MXC_EHCI_MODE_UTMI) 181 182 /* mmc driver */ 183 #define CONFIG_FSL_ESDHC 184 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 185 #define CONFIG_SYS_FSL_ESDHC_NUM 1 186 187 /* 188 * Default environment and default scripts 189 * to update uboot and load kernel 190 */ 191 192 #define CONFIG_HOSTNAME "mx35pdk" 193 #define CONFIG_EXTRA_ENV_SETTINGS \ 194 "netdev=eth1\0" \ 195 "ethprime=smc911x\0" \ 196 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 197 "nfsroot=${serverip}:${rootpath}\0" \ 198 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 199 "addip_sta=setenv bootargs ${bootargs} " \ 200 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 201 ":${hostname}:${netdev}:off panic=1\0" \ 202 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ 203 "addip=if test -n ${ipdyn};then run addip_dyn;" \ 204 "else run addip_sta;fi\0" \ 205 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 206 "addtty=setenv bootargs ${bootargs}" \ 207 " console=ttymxc0,${baudrate}\0" \ 208 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ 209 "loadaddr=80800000\0" \ 210 "kernel_addr_r=80800000\0" \ 211 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \ 212 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \ 213 "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0" \ 214 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 215 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 216 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 217 "bootm ${kernel_addr}\0" \ 218 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 219 "run nfsargs addip addtty addmtd addmisc;" \ 220 "bootm ${kernel_addr_r}\0" \ 221 "net_self_load=tftp ${kernel_addr_r} ${bootfile};" \ 222 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \ 223 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \ 224 "load=tftp ${loadaddr} ${u-boot}\0" \ 225 "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \ 226 "update=protect off ${uboot_addr} +80000;" \ 227 "erase ${uboot_addr} +80000;" \ 228 "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \ 229 "upd=if run load;then echo Updating u-boot;if run update;" \ 230 "then echo U-Boot updated;" \ 231 "else echo Error updating u-boot !;" \ 232 "echo Board without bootloader !!;" \ 233 "fi;" \ 234 "else echo U-Boot not downloaded..exiting;fi\0" \ 235 "bootcmd=run net_nfs\0" 236 237 #endif /* __CONFIG_H */ 238