1 /* 2 * Copyright (C) 2013 Marek Vasut <marex@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 #ifndef __CONFIGS_MX23_OLINUXINO_H__ 7 #define __CONFIGS_MX23_OLINUXINO_H__ 8 9 /* System configurations */ 10 #define CONFIG_MX23 /* i.MX23 SoC */ 11 #define CONFIG_MACH_TYPE 4105 12 13 /* U-Boot Commands */ 14 #define CONFIG_SYS_NO_FLASH 15 #define CONFIG_DISPLAY_CPUINFO 16 #define CONFIG_DOS_PARTITION 17 18 #define CONFIG_CMD_LED 19 20 /* Memory configuration */ 21 #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ 22 #define PHYS_SDRAM_1 0x40000000 /* Base address */ 23 #define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */ 24 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 25 26 /* Environment */ 27 #define CONFIG_ENV_IS_IN_MMC 28 #define CONFIG_ENV_OVERWRITE 29 30 /* Environment is in MMC */ 31 #if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) 32 #define CONFIG_ENV_OFFSET (256 * 1024) 33 #define CONFIG_ENV_SIZE (16 * 1024) 34 #define CONFIG_SYS_MMC_ENV_DEV 0 35 #endif 36 37 /* Status LED */ 38 #define CONFIG_STATUS_LED 39 #define CONFIG_GPIO_LED 40 #define CONFIG_BOARD_SPECIFIC_LED 41 #define STATUS_LED_BOOT 0 42 #define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1 43 #define STATUS_LED_STATE STATUS_LED_ON 44 #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) 45 46 /* USB */ 47 #ifdef CONFIG_CMD_USB 48 #define CONFIG_EHCI_MXS_PORT0 49 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 50 #define CONFIG_USB_STORAGE 51 #endif 52 53 /* Ethernet */ 54 #ifdef CONFIG_CMD_NET 55 #define CONFIG_USB_HOST_ETHER 56 #define CONFIG_USB_ETHER_SMSC95XX 57 #endif 58 59 /* Booting Linux */ 60 #define CONFIG_BOOTDELAY 3 61 #define CONFIG_BOOTFILE "uImage" 62 #define CONFIG_LOADADDR 0x42000000 63 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 64 65 /* Extra Environment */ 66 #define CONFIG_EXTRA_ENV_SETTINGS \ 67 "update_sd_firmware_filename=u-boot.sd\0" \ 68 "update_sd_firmware=" /* Update the SD firmware partition */ \ 69 "if mmc rescan ; then " \ 70 "if tftp ${update_sd_firmware_filename} ; then " \ 71 "setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \ 72 "setexpr fw_sz ${fw_sz} + 1 ; " \ 73 "mmc write ${loadaddr} 0x800 ${fw_sz} ; " \ 74 "fi ; " \ 75 "fi\0" \ 76 "script=boot.scr\0" \ 77 "uimage=uImage\0" \ 78 "console=ttyAMA0\0" \ 79 "fdt_file=imx23-olinuxino.dtb\0" \ 80 "fdt_addr=0x41000000\0" \ 81 "boot_fdt=try\0" \ 82 "ip_dyn=yes\0" \ 83 "mmcdev=0\0" \ 84 "mmcpart=2\0" \ 85 "mmcroot=/dev/mmcblk0p3 rw rootwait\0" \ 86 "mmcargs=setenv bootargs console=${console},${baudrate} " \ 87 "root=${mmcroot}\0" \ 88 "loadbootscript=" \ 89 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ 90 "bootscript=echo Running bootscript from mmc ...; " \ 91 "source\0" \ 92 "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ 93 "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ 94 "mmcboot=echo Booting from mmc ...; " \ 95 "run mmcargs; " \ 96 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 97 "if run loadfdt; then " \ 98 "bootm ${loadaddr} - ${fdt_addr}; " \ 99 "else " \ 100 "if test ${boot_fdt} = try; then " \ 101 "bootm; " \ 102 "else " \ 103 "echo WARN: Cannot load the DT; " \ 104 "fi; " \ 105 "fi; " \ 106 "else " \ 107 "bootm; " \ 108 "fi;\0" \ 109 "netargs=setenv bootargs console=${console},${baudrate} " \ 110 "root=/dev/nfs " \ 111 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ 112 "netboot=echo Booting from net ...; " \ 113 "usb start; " \ 114 "run netargs; " \ 115 "if test ${ip_dyn} = yes; then " \ 116 "setenv get_cmd dhcp; " \ 117 "else " \ 118 "setenv get_cmd tftp; " \ 119 "fi; " \ 120 "${get_cmd} ${uimage}; " \ 121 "if test ${boot_fdt} = yes; then " \ 122 "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ 123 "bootm ${loadaddr} - ${fdt_addr}; " \ 124 "else " \ 125 "if test ${boot_fdt} = try; then " \ 126 "bootm; " \ 127 "else " \ 128 "echo WARN: Cannot load the DT; " \ 129 "fi;" \ 130 "fi; " \ 131 "else " \ 132 "bootm; " \ 133 "fi;\0" 134 135 #define CONFIG_BOOTCOMMAND \ 136 "mmc dev ${mmcdev}; if mmc rescan; then " \ 137 "if run loadbootscript; then " \ 138 "run bootscript; " \ 139 "else " \ 140 "if run loaduimage; then " \ 141 "run mmcboot; " \ 142 "else run netboot; " \ 143 "fi; " \ 144 "fi; " \ 145 "else run netboot; fi" 146 147 /* The rest of the configuration is shared */ 148 #include <configs/mxs.h> 149 150 #endif /* __CONFIGS_MX23_OLINUXINO_H__ */ 151