1 /* 2 * Configuation settings for the Hitachi Solution Engine 7722 3 * 4 * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __MS7722SE_H 10 #define __MS7722SE_H 11 12 #define CONFIG_CPU_SH7722 1 13 14 #define CONFIG_DISPLAY_BOARDINFO 15 #undef CONFIG_SHOW_BOOT_PROGRESS 16 17 /* SMC9111 */ 18 #define CONFIG_SMC91111 19 #define CONFIG_SMC91111_BASE (0xB8000000) 20 21 /* MEMORY */ 22 #define MS7722SE_SDRAM_BASE (0x8C000000) 23 #define MS7722SE_FLASH_BASE_1 (0xA0000000) 24 #define MS7722SE_FLASH_BANK_SIZE (8*1024 * 1024) 25 26 #define CONFIG_SYS_PBSIZE 256 /* Buffer size for Console output */ 27 #define CONFIG_SYS_BAUDRATE_TABLE { 115200 } /* List of legal baudrate settings for this board */ 28 29 /* SCIF */ 30 #define CONFIG_CONS_SCIF0 1 31 32 #define CONFIG_SYS_MEMTEST_START (MS7722SE_SDRAM_BASE) 33 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024)) 34 35 #undef CONFIG_SYS_ALT_MEMTEST /* Enable alternate, more extensive, memory test */ 36 #undef CONFIG_SYS_MEMTEST_SCRATCH /* Scratch address used by the alternate memory test */ 37 38 #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* Enable temporary baudrate change while serial download */ 39 40 #define CONFIG_SYS_SDRAM_BASE (MS7722SE_SDRAM_BASE) 41 #define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* maybe more, but if so u-boot doesn't know about it... */ 42 43 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 4 * 1024 * 1024) /* default load address for scripts ?!? */ 44 45 #define CONFIG_SYS_MONITOR_BASE (MS7722SE_FLASH_BASE_1) /* Address of u-boot image 46 in Flash (NOT run time address in SDRAM) ?!? */ 47 #define CONFIG_SYS_MONITOR_LEN (128 * 1024) /* */ 48 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ 49 #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) 50 51 /* FLASH */ 52 #define CONFIG_SYS_FLASH_CFI 53 #define CONFIG_FLASH_CFI_DRIVER 54 #undef CONFIG_SYS_FLASH_QUIET_TEST 55 #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ 56 57 #define CONFIG_SYS_FLASH_BASE (MS7722SE_FLASH_BASE_1) /* Physical start address of Flash memory */ 58 59 #define CONFIG_SYS_MAX_FLASH_SECT 150 /* Max number of sectors on each 60 Flash chip */ 61 62 /* if you use all NOR Flash , you change dip-switch. Please see MS7722SE01 Manual. */ 63 #define CONFIG_SYS_MAX_FLASH_BANKS 2 64 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + (0 * MS7722SE_FLASH_BANK_SIZE), \ 65 CONFIG_SYS_FLASH_BASE + (1 * MS7722SE_FLASH_BANK_SIZE), \ 66 } 67 68 #define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) /* Timeout for Flash erase operations (in ms) */ 69 #define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) /* Timeout for Flash write operations (in ms) */ 70 #define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) /* Timeout for Flash set sector lock bit operations (in ms) */ 71 #define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) /* Timeout for Flash clear lock bit operations (in ms) */ 72 73 #undef CONFIG_SYS_FLASH_PROTECTION /* Use hardware flash sectors protection instead of U-Boot software protection */ 74 75 #undef CONFIG_SYS_DIRECT_FLASH_TFTP 76 77 #define CONFIG_ENV_OVERWRITE 1 78 #define CONFIG_ENV_SECT_SIZE (8 * 1024) 79 #define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) 80 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + (1 * CONFIG_ENV_SECT_SIZE)) 81 #define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) /* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ 82 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) 83 #define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) 84 85 /* Board Clock */ 86 #define CONFIG_SYS_CLK_FREQ 33333333 87 #define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ 88 #define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ 89 #define CONFIG_SYS_TMU_CLK_DIV (4) /* 4 (default), 16, 64, 256 or 1024 */ 90 91 #endif /* __MS7722SE_H */ 92