1 /* 2 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. 3 * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com 4 * 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 #define CONFIG_E300 1 /* E300 family */ 16 #define CONFIG_MPC830x 1 /* MPC830x family */ 17 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 18 19 /* 20 * On-board devices 21 * 22 * TSECs 23 */ 24 #define CONFIG_TSEC1 25 #define CONFIG_TSEC2 26 27 /* 28 * System Clock Setup 29 */ 30 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 31 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 32 33 /* 34 * Hardware Reset Configuration Word 35 * if CLKIN is 66.66MHz, then 36 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 37 * We choose the A type silicon as default, so the core is 400Mhz. 38 */ 39 #define CONFIG_SYS_HRCW_LOW (\ 40 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 41 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 42 HRCWL_SVCOD_DIV_2 |\ 43 HRCWL_CSB_TO_CLKIN_4X1 |\ 44 HRCWL_CORE_TO_CSB_3X1) 45 /* 46 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 47 * in 8308's HRCWH according to the manual, but original Freescale's 48 * code has them and I've expirienced some problems using the board 49 * with BDI3000 attached when I've tried to set these bits to zero 50 * (UART doesn't work after the 'reset run' command). 51 */ 52 #define CONFIG_SYS_HRCW_HIGH (\ 53 HRCWH_PCI_HOST |\ 54 HRCWH_PCI1_ARBITER_ENABLE |\ 55 HRCWH_CORE_ENABLE |\ 56 HRCWH_FROM_0X00000100 |\ 57 HRCWH_BOOTSEQ_DISABLE |\ 58 HRCWH_SW_WATCHDOG_DISABLE |\ 59 HRCWH_ROM_LOC_LOCAL_16BIT |\ 60 HRCWH_RL_EXT_LEGACY |\ 61 HRCWH_TSEC1M_IN_MII |\ 62 HRCWH_TSEC2M_IN_MII |\ 63 HRCWH_BIG_ENDIAN) 64 65 /* 66 * System IO Config 67 */ 68 #define CONFIG_SYS_SICRH (\ 69 SICRH_ESDHC_A_GPIO |\ 70 SICRH_ESDHC_B_GPIO |\ 71 SICRH_ESDHC_C_GTM |\ 72 SICRH_GPIO_A_TSEC2 |\ 73 SICRH_GPIO_B_TSEC2_TX_CLK |\ 74 SICRH_IEEE1588_A_GPIO |\ 75 SICRH_USB |\ 76 SICRH_GTM_GPIO |\ 77 SICRH_IEEE1588_B_GPIO |\ 78 SICRH_ETSEC2_CRS |\ 79 SICRH_GPIOSEL_1 |\ 80 SICRH_TMROBI_V3P3 |\ 81 SICRH_TSOBI1_V3P3 |\ 82 SICRH_TSOBI2_V3P3) /* 0xf577d100 */ 83 #define CONFIG_SYS_SICRL (\ 84 SICRL_SPI_PF0 |\ 85 SICRL_UART_PF0 |\ 86 SICRL_IRQ_PF0 |\ 87 SICRL_I2C2_PF0 |\ 88 SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ 89 90 #define CONFIG_SYS_GPIO1_PRELIM 91 /* GPIO Default input/output settings */ 92 #define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00 93 /* 94 * Default GPIO values: 95 * LED#1 enabled; WLAN enabled; Both COM LED on (orange) 96 */ 97 #define CONFIG_SYS_GPIO1_DAT 0x08008C00 98 99 /* 100 * IMMR new address 101 */ 102 #define CONFIG_SYS_IMMR 0xE0000000 103 104 /* 105 * SERDES 106 */ 107 #define CONFIG_FSL_SERDES 108 #define CONFIG_FSL_SERDES1 0xe3000 109 110 /* 111 * Arbiter Setup 112 */ 113 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 114 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 115 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 116 117 /* 118 * DDR Setup 119 */ 120 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 121 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 122 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 123 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 124 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 125 | DDRCDR_PZ_LOZ \ 126 | DDRCDR_NZ_LOZ \ 127 | DDRCDR_ODT \ 128 | DDRCDR_Q_DRN) 129 /* 0x7b880001 */ 130 /* 131 * Manually set up DDR parameters 132 * consist of two chips HY5PS12621BFP-C4 from HYNIX 133 */ 134 135 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 136 137 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 138 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 139 | CSCONFIG_ODT_RD_NEVER \ 140 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 141 | CSCONFIG_ROW_BIT_13 \ 142 | CSCONFIG_COL_BIT_10) 143 /* 0x80010102 */ 144 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 145 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 146 | (0 << TIMING_CFG0_WRT_SHIFT) \ 147 | (0 << TIMING_CFG0_RRT_SHIFT) \ 148 | (0 << TIMING_CFG0_WWT_SHIFT) \ 149 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 150 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 151 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 152 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 153 /* 0x00220802 */ 154 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 155 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 156 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 157 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 158 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 159 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 160 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 161 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 162 /* 0x27256222 */ 163 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 164 | (4 << TIMING_CFG2_CPO_SHIFT) \ 165 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 166 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 167 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 168 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 169 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 170 /* 0x121048c5 */ 171 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ 172 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 173 /* 0x03600100 */ 174 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 175 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 176 | SDRAM_CFG_DBW_32) 177 /* 0x43080000 */ 178 179 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 180 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 181 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 182 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 183 #define CONFIG_SYS_DDR_MODE2 0x00000000 184 185 /* 186 * Memory test 187 */ 188 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 189 #define CONFIG_SYS_MEMTEST_END 0x07f00000 190 191 /* 192 * The reserved memory 193 */ 194 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 195 196 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 197 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 198 199 /* 200 * Initial RAM Base Address Setup 201 */ 202 #define CONFIG_SYS_INIT_RAM_LOCK 1 203 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 204 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 205 #define CONFIG_SYS_GBL_DATA_OFFSET \ 206 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 207 208 /* 209 * Local Bus Configuration & Clock Setup 210 */ 211 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 212 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 213 #define CONFIG_SYS_LBC_LBCR 0x00040000 214 215 /* 216 * FLASH on the Local Bus 217 */ 218 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 219 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 220 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 221 222 #define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */ 223 #define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */ 224 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 225 226 /* Window base at flash base */ 227 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 228 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) 229 230 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 231 | BR_PS_16 /* 16 bit port */ \ 232 | BR_MS_GPCM /* MSEL = GPCM */ \ 233 | BR_V) /* valid */ 234 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 235 | OR_UPM_XAM \ 236 | OR_GPCM_CSNT \ 237 | OR_GPCM_ACS_DIV2 \ 238 | OR_GPCM_XACS \ 239 | OR_GPCM_SCY_4 \ 240 | OR_GPCM_TRLX_SET \ 241 | OR_GPCM_EHTR_SET) 242 243 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 244 #define CONFIG_SYS_MAX_FLASH_SECT 512 245 246 /* Flash Erase Timeout (ms) */ 247 #define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024) 248 /* Flash Write Timeout (ms) */ 249 #define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024) 250 251 /* 252 * SJA1000 CAN controller on Local Bus 253 */ 254 #define CONFIG_SYS_SJA1000_BASE 0xFBFF0000 255 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SJA1000_BASE \ 256 | BR_PS_8 /* 8 bit port size */ \ 257 | BR_MS_GPCM /* MSEL = GPCM */ \ 258 | BR_V) /* valid */ 259 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 260 | OR_GPCM_SCY_5 \ 261 | OR_GPCM_EHTR_SET) 262 /* 0xFFFF8052 */ 263 264 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE 265 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 266 267 /* 268 * CPLD on Local Bus 269 */ 270 #define CONFIG_SYS_CPLD_BASE 0xFBFF8000 271 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_CPLD_BASE \ 272 | BR_PS_8 /* 8 bit port */ \ 273 | BR_MS_GPCM /* MSEL = GPCM */ \ 274 | BR_V) /* valid */ 275 #define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB \ 276 | OR_GPCM_SCY_4 \ 277 | OR_GPCM_EHTR_SET) 278 /* 0xFFFF8042 */ 279 280 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE 281 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 282 283 /* 284 * Serial Port 285 */ 286 #undef CONFIG_SERIAL_SOFTWARE_FIFO 287 #define CONFIG_SYS_NS16550_SERIAL 288 #define CONFIG_SYS_NS16550_REG_SIZE 1 289 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 290 291 #define CONFIG_SYS_BAUDRATE_TABLE \ 292 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 293 294 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 295 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 296 297 /* I2C */ 298 #define CONFIG_SYS_I2C 299 #define CONFIG_SYS_I2C_FSL 300 #define CONFIG_SYS_FSL_I2C_SPEED 400000 301 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 302 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 303 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 304 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 305 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 306 307 /* 308 * General PCI 309 * Addresses are mapped 1-1. 310 */ 311 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 312 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 313 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 314 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 315 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 316 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 317 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 318 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 319 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 320 321 /* enable PCIE clock */ 322 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 323 324 #define CONFIG_PCI_INDIRECT_BRIDGE 325 #define CONFIG_PCIE 326 327 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 328 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 329 330 /* 331 * TSEC 332 */ 333 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 334 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 335 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 336 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 337 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 338 339 /* 340 * TSEC ethernet configuration 341 */ 342 #define CONFIG_MII 1 /* MII PHY management */ 343 #define CONFIG_TSEC1_NAME "eTSEC0" 344 #define CONFIG_TSEC2_NAME "eTSEC1" 345 #define TSEC1_PHY_ADDR 1 346 #define TSEC2_PHY_ADDR 2 347 #define TSEC1_PHYIDX 0 348 #define TSEC2_PHYIDX 0 349 #define TSEC1_FLAGS 0 350 #define TSEC2_FLAGS 0 351 352 /* Options are: eTSEC[0-1] */ 353 #define CONFIG_ETHPRIME "eTSEC0" 354 355 /* 356 * Environment 357 */ 358 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 359 CONFIG_SYS_MONITOR_LEN) 360 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 361 #define CONFIG_ENV_SIZE 0x2000 362 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 363 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 364 365 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 366 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 367 368 /* 369 * BOOTP options 370 */ 371 #define CONFIG_BOOTP_BOOTFILESIZE 372 373 /* 374 * Command line configuration. 375 */ 376 377 /* 378 * Miscellaneous configurable options 379 */ 380 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 381 382 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 383 384 /* Boot Argument Buffer Size */ 385 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 386 387 /* 388 * For booting Linux, the board info and command line data 389 * have to be in the first 8 MB of memory, since this is 390 * the maximum mapped by the Linux kernel during initialization. 391 */ 392 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 393 394 /* 395 * Core HID Setup 396 */ 397 #define CONFIG_SYS_HID0_INIT 0x000000000 398 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 399 HID0_ENABLE_INSTRUCTION_CACHE | \ 400 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 401 #define CONFIG_SYS_HID2 HID2_HBE 402 403 /* 404 * MMU Setup 405 */ 406 407 /* DDR: cache cacheable */ 408 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 409 BATL_MEMCOHERENCE) 410 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 411 BATU_VS | BATU_VP) 412 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 413 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 414 415 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 416 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 417 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 418 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 419 BATU_VP) 420 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 421 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 422 423 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 424 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 425 BATL_MEMCOHERENCE) 426 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 427 BATU_VS | BATU_VP) 428 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 429 BATL_CACHEINHIBIT | \ 430 BATL_GUARDEDSTORAGE) 431 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 432 433 /* Stack in dcache: cacheable, no memory coherence */ 434 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 435 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 436 BATU_VS | BATU_VP) 437 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 438 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 439 440 /* 441 * Environment Configuration 442 */ 443 444 #define CONFIG_ENV_OVERWRITE 445 446 #if defined(CONFIG_TSEC_ENET) 447 #define CONFIG_HAS_ETH0 448 #define CONFIG_HAS_ETH1 449 #endif 450 451 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 452 453 454 #define CONFIG_EXTRA_ENV_SETTINGS \ 455 "netdev=eth0\0" \ 456 "consoledev=ttyS0\0" \ 457 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 458 "nfsroot=${serverip}:${rootpath}\0" \ 459 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 460 "addip=setenv bootargs ${bootargs} " \ 461 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 462 ":${hostname}:${netdev}:off panic=1\0" \ 463 "addtty=setenv bootargs ${bootargs}" \ 464 " console=${consoledev},${baudrate}\0" \ 465 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 466 "addmisc=setenv bootargs ${bootargs}\0" \ 467 "kernel_addr=FC0A0000\0" \ 468 "fdt_addr=FC2A0000\0" \ 469 "ramdisk_addr=FC2C0000\0" \ 470 "u-boot=mpc8308_p1m/u-boot.bin\0" \ 471 "kernel_addr_r=1000000\0" \ 472 "fdt_addr_r=C00000\0" \ 473 "hostname=mpc8308_p1m\0" \ 474 "bootfile=mpc8308_p1m/uImage\0" \ 475 "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \ 476 "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ 477 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 478 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 479 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 480 "bootm ${kernel_addr} - ${fdt_addr}\0" \ 481 "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ 482 "tftp ${fdt_addr_r} ${fdtfile};" \ 483 "run nfsargs addip addtty addmtd addmisc;" \ 484 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 485 "bootcmd=run flash_self\0" \ 486 "load=tftp ${loadaddr} ${u-boot}\0" \ 487 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 488 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 489 " +${filesize};cp.b ${fileaddr} " \ 490 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 491 "upd=run load update\0" \ 492 493 #endif /* __CONFIG_H */ 494