1 /* 2 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. 3 * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com 4 * 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 22 * MA 02111-1307 USA 23 */ 24 25 #ifndef __CONFIG_H 26 #define __CONFIG_H 27 28 /* 29 * High Level Configuration Options 30 */ 31 #define CONFIG_E300 1 /* E300 family */ 32 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 33 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 34 #define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */ 35 36 #ifndef CONFIG_SYS_TEXT_BASE 37 #define CONFIG_SYS_TEXT_BASE 0xFC000000 38 #endif 39 40 /* 41 * On-board devices 42 * 43 * TSECs 44 */ 45 #define CONFIG_TSEC1 46 #define CONFIG_TSEC2 47 48 /* 49 * System Clock Setup 50 */ 51 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 52 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 53 54 /* 55 * Hardware Reset Configuration Word 56 * if CLKIN is 66.66MHz, then 57 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 58 * We choose the A type silicon as default, so the core is 400Mhz. 59 */ 60 #define CONFIG_SYS_HRCW_LOW (\ 61 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 62 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 63 HRCWL_SVCOD_DIV_2 |\ 64 HRCWL_CSB_TO_CLKIN_4X1 |\ 65 HRCWL_CORE_TO_CSB_3X1) 66 /* 67 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 68 * in 8308's HRCWH according to the manual, but original Freescale's 69 * code has them and I've expirienced some problems using the board 70 * with BDI3000 attached when I've tried to set these bits to zero 71 * (UART doesn't work after the 'reset run' command). 72 */ 73 #define CONFIG_SYS_HRCW_HIGH (\ 74 HRCWH_PCI_HOST |\ 75 HRCWH_PCI1_ARBITER_ENABLE |\ 76 HRCWH_CORE_ENABLE |\ 77 HRCWH_FROM_0X00000100 |\ 78 HRCWH_BOOTSEQ_DISABLE |\ 79 HRCWH_SW_WATCHDOG_DISABLE |\ 80 HRCWH_ROM_LOC_LOCAL_16BIT |\ 81 HRCWH_RL_EXT_LEGACY |\ 82 HRCWH_TSEC1M_IN_MII |\ 83 HRCWH_TSEC2M_IN_MII |\ 84 HRCWH_BIG_ENDIAN) 85 86 /* 87 * System IO Config 88 */ 89 #define CONFIG_SYS_SICRH (\ 90 SICRH_ESDHC_A_GPIO |\ 91 SICRH_ESDHC_B_GPIO |\ 92 SICRH_ESDHC_C_GTM |\ 93 SICRH_GPIO_A_TSEC2 |\ 94 SICRH_GPIO_B_TSEC2_TX_CLK |\ 95 SICRH_IEEE1588_A_GPIO |\ 96 SICRH_USB |\ 97 SICRH_GTM_GPIO |\ 98 SICRH_IEEE1588_B_GPIO |\ 99 SICRH_ETSEC2_CRS |\ 100 SICRH_GPIOSEL_1 |\ 101 SICRH_TMROBI_V3P3 |\ 102 SICRH_TSOBI1_V3P3 |\ 103 SICRH_TSOBI2_V3P3) /* 0xf577d100 */ 104 #define CONFIG_SYS_SICRL (\ 105 SICRL_SPI_PF0 |\ 106 SICRL_UART_PF0 |\ 107 SICRL_IRQ_PF0 |\ 108 SICRL_I2C2_PF0 |\ 109 SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ 110 111 #define CONFIG_SYS_GPIO1_PRELIM 112 /* GPIO Default input/output settings */ 113 #define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00 114 /* 115 * Default GPIO values: 116 * LED#1 enabled; WLAN enabled; Both COM LED on (orange) 117 */ 118 #define CONFIG_SYS_GPIO1_DAT 0x08008C00 119 120 /* 121 * IMMR new address 122 */ 123 #define CONFIG_SYS_IMMR 0xE0000000 124 125 /* 126 * SERDES 127 */ 128 #define CONFIG_FSL_SERDES 129 #define CONFIG_FSL_SERDES1 0xe3000 130 131 /* 132 * Arbiter Setup 133 */ 134 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 135 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 136 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 137 138 /* 139 * DDR Setup 140 */ 141 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 142 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 143 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 144 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 145 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 146 | DDRCDR_PZ_LOZ \ 147 | DDRCDR_NZ_LOZ \ 148 | DDRCDR_ODT \ 149 | DDRCDR_Q_DRN) 150 /* 0x7b880001 */ 151 /* 152 * Manually set up DDR parameters 153 * consist of two chips HY5PS12621BFP-C4 from HYNIX 154 */ 155 156 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 157 158 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 159 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 160 | 0x00010000 /* ODT_WR to CSn */ \ 161 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 162 /* 0x80010102 */ 163 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 164 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 165 | (0 << TIMING_CFG0_WRT_SHIFT) \ 166 | (0 << TIMING_CFG0_RRT_SHIFT) \ 167 | (0 << TIMING_CFG0_WWT_SHIFT) \ 168 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 169 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 170 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 171 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 172 /* 0x00220802 */ 173 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 174 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 175 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 176 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 177 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 178 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 179 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 180 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 181 /* 0x27256222 */ 182 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 183 | (4 << TIMING_CFG2_CPO_SHIFT) \ 184 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 185 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 186 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 187 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 188 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 189 /* 0x121048c5 */ 190 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ 191 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 192 /* 0x03600100 */ 193 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 194 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 195 | SDRAM_CFG_32_BE) 196 /* 0x43080000 */ 197 198 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 199 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 200 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 201 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 202 #define CONFIG_SYS_DDR_MODE2 0x00000000 203 204 /* 205 * Memory test 206 */ 207 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 208 #define CONFIG_SYS_MEMTEST_END 0x07f00000 209 210 /* 211 * The reserved memory 212 */ 213 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 214 215 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 216 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 217 218 /* 219 * Initial RAM Base Address Setup 220 */ 221 #define CONFIG_SYS_INIT_RAM_LOCK 1 222 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 223 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 224 #define CONFIG_SYS_GBL_DATA_OFFSET \ 225 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 226 227 /* 228 * Local Bus Configuration & Clock Setup 229 */ 230 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 231 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 232 #define CONFIG_SYS_LBC_LBCR 0x00040000 233 234 /* 235 * FLASH on the Local Bus 236 */ 237 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 238 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 239 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 240 241 #define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */ 242 #define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */ 243 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 244 245 /* Window base at flash base */ 246 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 247 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) 248 249 #define CONFIG_SYS_BR0_PRELIM (\ 250 CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\ 251 (2 << BR_PS_SHIFT) /* 16 bit port size */ |\ 252 BR_V) /* valid */ 253 #define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ 254 | OR_UPM_XAM \ 255 | OR_GPCM_CSNT \ 256 | OR_GPCM_ACS_DIV2 \ 257 | OR_GPCM_XACS \ 258 | OR_GPCM_SCY_4 \ 259 | OR_GPCM_TRLX \ 260 | OR_GPCM_EHTR \ 261 | OR_GPCM_EAD) 262 263 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 264 #define CONFIG_SYS_MAX_FLASH_SECT 512 265 266 /* Flash Erase Timeout (ms) */ 267 #define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024) 268 /* Flash Write Timeout (ms) */ 269 #define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024) 270 271 /* 272 * SJA1000 CAN controller on Local Bus 273 */ 274 #define CONFIG_SYS_SJA1000_BASE 0xFBFF0000 275 #define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_SJA1000_BASE \ 276 | (1 << BR_PS_SHIFT) /* 8 bit port size */ \ 277 | BR_V ) /* valid */ 278 #define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \ 279 | OR_GPCM_SCY_5 \ 280 | OR_GPCM_EHTR) 281 /* 0xFFFF8052 */ 282 283 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE 284 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 285 286 /* 287 * CPLD on Local Bus 288 */ 289 #define CONFIG_SYS_CPLD_BASE 0xFBFF8000 290 #define CONFIG_SYS_BR2_PRELIM ( CONFIG_SYS_CPLD_BASE \ 291 | (1 << BR_PS_SHIFT) /* 8 bit port size */ \ 292 | BR_V ) /* valid */ 293 #define CONFIG_SYS_OR2_PRELIM ( 0xFFFF8000 /* length 32K */ \ 294 | OR_GPCM_SCY_4 \ 295 | OR_GPCM_EHTR) 296 /* 0xFFFF8042 */ 297 298 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE 299 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 300 301 /* 302 * Serial Port 303 */ 304 #define CONFIG_CONS_INDEX 1 305 #undef CONFIG_SERIAL_SOFTWARE_FIFO 306 #define CONFIG_SYS_NS16550 307 #define CONFIG_SYS_NS16550_SERIAL 308 #define CONFIG_SYS_NS16550_REG_SIZE 1 309 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 310 311 #define CONFIG_SYS_BAUDRATE_TABLE \ 312 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 313 314 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 315 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 316 317 /* Use the HUSH parser */ 318 #define CONFIG_SYS_HUSH_PARSER 319 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 320 321 /* Pass open firmware flat tree */ 322 #define CONFIG_OF_LIBFDT 1 323 #define CONFIG_OF_BOARD_SETUP 1 324 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 325 326 /* I2C */ 327 #define CONFIG_HARD_I2C /* I2C with hardware support */ 328 #define CONFIG_FSL_I2C 329 #define CONFIG_I2C_MULTI_BUS 330 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 331 #define CONFIG_SYS_I2C_SLAVE 0x7F 332 #define CONFIG_SYS_I2C_OFFSET 0x3000 333 #define CONFIG_SYS_I2C2_OFFSET 0x3100 334 335 /* 336 * General PCI 337 * Addresses are mapped 1-1. 338 */ 339 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 340 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 341 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 342 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 343 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 344 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 345 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 346 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 347 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 348 349 /* enable PCIE clock */ 350 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 351 352 #define CONFIG_PCI 353 #define CONFIG_PCIE 354 355 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 356 357 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 358 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 359 360 /* 361 * TSEC 362 */ 363 #define CONFIG_NET_MULTI 364 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 365 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 366 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 367 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 368 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 369 370 /* 371 * TSEC ethernet configuration 372 */ 373 #define CONFIG_MII 1 /* MII PHY management */ 374 #define CONFIG_TSEC1_NAME "eTSEC0" 375 #define CONFIG_TSEC2_NAME "eTSEC1" 376 #define TSEC1_PHY_ADDR 1 377 #define TSEC2_PHY_ADDR 2 378 #define TSEC1_PHYIDX 0 379 #define TSEC2_PHYIDX 0 380 #define TSEC1_FLAGS 0 381 #define TSEC2_FLAGS 0 382 383 /* Options are: eTSEC[0-1] */ 384 #define CONFIG_ETHPRIME "eTSEC0" 385 386 /* 387 * Environment 388 */ 389 #define CONFIG_ENV_IS_IN_FLASH 1 390 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 391 CONFIG_SYS_MONITOR_LEN) 392 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 393 #define CONFIG_ENV_SIZE 0x2000 394 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 395 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 396 397 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 398 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 399 400 /* 401 * BOOTP options 402 */ 403 #define CONFIG_BOOTP_BOOTFILESIZE 404 #define CONFIG_BOOTP_BOOTPATH 405 #define CONFIG_BOOTP_GATEWAY 406 #define CONFIG_BOOTP_HOSTNAME 407 408 /* 409 * Command line configuration. 410 */ 411 #include <config_cmd_default.h> 412 413 #define CONFIG_CMD_DHCP 414 #define CONFIG_CMD_I2C 415 #define CONFIG_CMD_MII 416 #define CONFIG_CMD_NET 417 #define CONFIG_CMD_PCI 418 #define CONFIG_CMD_PING 419 420 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 421 422 /* 423 * Miscellaneous configurable options 424 */ 425 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 426 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 427 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 428 429 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 430 431 /* Print Buffer Size */ 432 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 433 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 434 /* Boot Argument Buffer Size */ 435 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 436 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 437 438 /* 439 * For booting Linux, the board info and command line data 440 * have to be in the first 8 MB of memory, since this is 441 * the maximum mapped by the Linux kernel during initialization. 442 */ 443 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 444 445 /* 446 * Core HID Setup 447 */ 448 #define CONFIG_SYS_HID0_INIT 0x000000000 449 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 450 HID0_ENABLE_INSTRUCTION_CACHE | \ 451 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 452 #define CONFIG_SYS_HID2 HID2_HBE 453 454 /* 455 * MMU Setup 456 */ 457 458 /* DDR: cache cacheable */ 459 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ 460 BATL_MEMCOHERENCE) 461 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 462 BATU_VS | BATU_VP) 463 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 464 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 465 466 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 467 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ 468 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 469 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 470 BATU_VP) 471 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 472 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 473 474 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 475 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ 476 BATL_MEMCOHERENCE) 477 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 478 BATU_VS | BATU_VP) 479 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ 480 BATL_CACHEINHIBIT | \ 481 BATL_GUARDEDSTORAGE) 482 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 483 484 /* Stack in dcache: cacheable, no memory coherence */ 485 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) 486 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 487 BATU_VS | BATU_VP) 488 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 489 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 490 491 /* 492 * Environment Configuration 493 */ 494 495 #define CONFIG_ENV_OVERWRITE 496 497 #if defined(CONFIG_TSEC_ENET) 498 #define CONFIG_HAS_ETH0 499 #define CONFIG_HAS_ETH1 500 #endif 501 502 #define CONFIG_BAUDRATE 115200 503 504 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 505 506 #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ 507 508 #define xstr(s) str(s) 509 #define str(s) #s 510 511 #define CONFIG_EXTRA_ENV_SETTINGS \ 512 "netdev=eth0\0" \ 513 "consoledev=ttyS0\0" \ 514 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 515 "nfsroot=${serverip}:${rootpath}\0" \ 516 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 517 "addip=setenv bootargs ${bootargs} " \ 518 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 519 ":${hostname}:${netdev}:off panic=1\0" \ 520 "addtty=setenv bootargs ${bootargs}" \ 521 " console=${consoledev},${baudrate}\0" \ 522 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 523 "addmisc=setenv bootargs ${bootargs}\0" \ 524 "kernel_addr=FC0A0000\0" \ 525 "fdt_addr=FC2A0000\0" \ 526 "ramdisk_addr=FC2C0000\0" \ 527 "u-boot=mpc8308_p1m/u-boot.bin\0" \ 528 "kernel_addr_r=1000000\0" \ 529 "fdt_addr_r=C00000\0" \ 530 "hostname=mpc8308_p1m\0" \ 531 "bootfile=mpc8308_p1m/uImage\0" \ 532 "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \ 533 "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ 534 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 535 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 536 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 537 "bootm ${kernel_addr} - ${fdt_addr}\0" \ 538 "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ 539 "tftp ${fdt_addr_r} ${fdtfile};" \ 540 "run nfsargs addip addtty addmtd addmisc;" \ 541 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 542 "bootcmd=run flash_self\0" \ 543 "load=tftp ${loadaddr} ${u-boot}\0" \ 544 "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \ 545 " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \ 546 " +${filesize};cp.b ${fileaddr} " \ 547 xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 548 "upd=run load update\0" \ 549 550 #endif /* __CONFIG_H */ 551